CATV
Community Antenna Television or. Community Access Television service.
-
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
Other CATV Meters
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers. also you can find other more equipment in CATV / Broadcasting fileds, such as Three Frequency Points, HFC Return Path Signal Generator, Return Path Signal Generator, Digital RF Signal Generator and so on.
-
Product
47~1200MHz FTTH CATV Optic Receiver
H1228
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H1228, the operating bandwidth of 47~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit. Receiving at high optical power can be adjusted by PAD level, played limiting output, so H1228 within a large dynamic range of the received optical power of +2 dBm ~-21dBm, have excellent characteristics.
-
Product
CATV MSA EDFA (1540~1563nm)
HA5700
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5700, the Mid-Stage Access (MSA) CATV fiber amplifier, is developed and produced specially for the dispersion compensation of over-long trunk. HA5700 is composed of lower noise per-amplifier (PA) and booster amplifier (BA). There is access connector between these two amplifiers and thus the dispersion compensation module (DCM) can be accessed in the mid-stage conveniently. It offers the most simple and effective application.
-
Product
CATV Measurement Receiver
VAROS 107
-
The VAROS 107 was specially designed for installation and maintenance of cable TV networks. The large high resolution TFT display, the backlit keyboard, the built-in DOCSIS 3.0 and EMI measurement all contribute to making work for the technician easier.
-
Product
CATV Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
Product
CATV & SAT IF Optical Receiver Module
MRS-26D
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
Product
CATV Line-Amplifier EDFA
HA5200
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5200 series C-Band line-amplifier EDFA (also knows as relay EDFA), is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Fiber CATV system operates generally in single wavelength that has no strict requirement on gain flatness. In order to reduce the effect of CNR deterioration caused by EDFA, input power should be as high as possible to make EDFA operate in saturated output power. The typical value of input power is >+3dBm.
-
Product
47~1200MHz FTTH CATV Optic Receiver
H1224
-
Hangzhou Huatai Optic Tech. Co., Ltd.
H1224, the operating bandwidth of 47 ~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and special low noise matching circuit.Receiving at high optical power can be adjusted by PAD level, played limiting output, so H1224 within a large dynamic range of the received optical power of +2 dBm ~-19dBm, have excellent characteristics.
-
Product
45~1050MHz FTTH CATV O/E Convertor
H9008B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008B series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
-
Product
CATV 1310nm Fiber Optic Transmitter
MX862T series
-
The MX862T series direct modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital information for CATV and/or telephony applications.
-
Product
47~862MHz FTTH CATV Optical Receiver
H9122
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9122, the operating bandwidth of 47~862MHz, Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit,Whether used in analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index. is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver.
-
Product
CATV & 4 10/100M LAN Triple play FTTH ONU
H9122-4FE
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9122-4FE, is a triple play,FTTH ONU Optical network unit . Products will be a high-performance optical receivers and CATV FTTH EPON ONU, integrated in an ultra-small metal box . Provides high-quality and high-speed data to the user CATV , language, video and other broadband business services . High-performance products , high compatibility and excellent cost performance, today's triple play, FTTH preferred device .
-
Product
45~1050MHz FTTH CATV O/E Convertor
H9008A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008A series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
-
Product
100GHz DWDM Optical Add/Drop Multiplexer (CATV Overlay Multiplexer)
OADM-1001-VOA (100GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1001-VOA is an optical Add-Drop multiplexer with 100GHz channel interval. It is based on mature thin film filter technology, sealed with metal shell, and featured with low insertion loss, high isolation, wide channel and flexible configuration. It is the ideal device to Add(insertion Add)/Drop(Tape-out Drop) a specific wavelength(OADM) in optical fiber DWDM system. OADM-1001-VOA configures a manual-adjust optical attenuation, for adjust the equilibrium the optical power between insert channel and main signal channel, which is conveniently used for VOD overlay in CATV system.
-
Product
CATV Separate Raman Amplifier
RFA4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Amplifier is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. Raman amplifier is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
47~1200MHz FTTH CATV AGC Optical Receiver
H1222G
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H1222G, the operating bandwidth of 47 ~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H1222G in the received optical power over a large dynamic range of +2 dBm ~ -20dBm, and have excellent properties.
-
Product
(125×150×30.5mm) High Power Multi-ports Output CATV FTTP EYDFA Module
EATV5400x-FM05
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5400 series is a low noise, high performance, high power multi-ports EYDFA module, which is specially designed for CATV system. It offers a flexible and low-cost FTTP solution for CATV large area coverage of metropolises and medium-sized cities.
-
Product
EDFA For CATV, FTTH And HFC Applications
MX-A5400 series
-
The EDFA is suitable for long haul transmission networks or FTTH distribution networks. This optical amplifier is packaged in a 19” rack mount housing to provide a complete optical communications solution. Maxcom offers our MX-A5400 platform which can be ordered with 8, 16, 32, 64, 128, 256 and 512 output ports and various output powers.
-
Product
CATV
-
Sharp Vision, always first in innovation, offers you complete range of DC FTTH products to enable you to achieve better picture & sound quality at low cost & high reliability. The full product range of DC – FTTH products includes Fiber Transmitter cum Fiber Amplifiers(FTFA), DC & Battery Transmitters, Fiber Amplifiers, Nodes, Hybrid Amplifiers, DC Tap off, Splitters and PSP.
-
Product
CATV Fiber Optic 1550nm Transmitter
T8500HC Series
-
The MX-T8500HC series externally modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
45~1050MHz FTTH CATV O/E Convertor
H9008C
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008C series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=68dBμ V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
-
Product
Hand Held Power Meter, CATV with 0.01dB Resolution
F18513HRCATV
-
A Fiber Optic Power Meter is the essential tool for measuring optical power within a fiber optic link. You will find that FIS Fiber Optic Hand Held Power Meters offer solid performance, portability and ease-of-use, all at a great price. These units are ideal for use in conjunction with our Fiber Optic Hand Held Light Sources.
-
Product
47~862MHz & 950~2600MHz CATV & Satellite TV Direct Modulated Optical Transmitter
HDS-26A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-26A series, adopts high linearity with cooling DFB laser and direct modulated way. It can transmit 47~862MHz CATV and 950~2600MHz SAT-IF live-broadcasting TV signal at one fiber.
-
Product
Small Form Factor (40×70×12mm) CATV EDFA Module (Full function)
EATV5100-FM01
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5100 series is a low noise, high performance, high cost-effective EDFA module, which is specially designed for CATV system. EATV5100-FM01 is a full function module, using 40×70×12mm mini package, with single channel and narrow bandwidth standard version. A standard 6-pin electric connector provides simple electrical connection. The module adopts a high performance uncooled pump laser, the output optical power up to 19dBm.
-
Product
Lightwave Component Analyzers (LCA)
-
The Lightwave Component Analyzer is the instrument of choice to test all relevant opto-electronic S-parameters, like S21, S11 and S22 for electro-optical components in 10Gb/s and 40Gb/s, Fibre Channel and CATV transmission systems as well as radio-over-fiber and A&D applications.
-
Product
Field Meter
EAP 301 HD
-
The AP301 HD is a field meter with total coverage of the terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
Product
Small Form Factor (40×70×12mm) CATV EDFA Module (Gain Block)
EATV5100-GM01
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5100 series is a low noise, high performance, high cost-effective EDFA module, which is specially designed for CATV system. EATV5100-GM01 is a gain module, using 40×70×12mm mini package, with single channel and narrow bandwidth standard version. A standard 6-pin or 12-pin electric connector provides simple electrical connection. The module adopts a high performance uncooled pump laser, the output optical power up to 19dBm.
-
Product
Encoder-Modulator
SFT3542H
-
Hangzhou Softel Optic Co., Ltd.
SFT3542H24 in 1 encoder modulator is SOFTEL’s newest devices which integrate encoding, multiplexing, scrambling and DVB-C/T modulation. It supports 24 CVBS input, one DVB-C tuner input and 128 IP input with Data1 (GE) and Data2 (FE) port. It also support DVB-C/T RF out with 4 adjacent carries (50MHz~960MHz), and support Data1 (GE) output port to support 4 MPTS out. This full function device makes it ideal for small CATV head end system, and it’s a smart choice for hotel TV system, entertainment system in sports bar, hospital, apartment…
