Reverberation Chambers
environment for EMC testing. Also known as: Reverb Chambers
See Also: Anechoic Chambers, EMC Test, Chambers, Anechoic Rooms, Reverb Chambers, Sound Chambers
-
Product
Electromagnetic anechoic box/Shield box/Anechoic chamber
-
The necessity of a wireless system test has risen by the spread of recent wireless telecommunication equipment as shown in cellular phone, wireless LAN, RF-ID tag and ETC (Electronic Toll Collection system). It is necessary for a wireless test to be performed in anechoic environment in which an external noise is intercepted and a radio wave does not reflect internally. An anechoic chamber (room version of a shield box) is proper facilities but needs a wide space and a huge cost. Especially, the equipment under wireless system test on the production line can not radiate any signal radio wave outside before approval. The shield box satisfies these conditions.
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Vacuum Chambers
CV 400/CV 250
-
The CV 250 and CV 400 are vacuum chambers for altitude flight simulation for avionics instruments such as altimeters, rate of climb indicators and all non pressurised equipment. They are fitted with pneumatic and electric connectors and a quick locking door.
-
Product
Reach-In Solar Panel Test Chamber
-
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
-
Product
Walk InDrive In Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Walk in/Drive in chambers can make test for large components, finished products like automobile.According to different test requirement and application, walk in chamber could divide into 2 types: Welded walk-in chamber and Modular walk-in chamber.
-
Product
Precision Humidity Chambers
ELH Series
-
The Edgetech Instruments Model ELH Series is a series of precision humidity chambers, with NIST traceable accuracies in humidity (±0.5% typical), temperature (±0.1°C) and dew point (±0.2°C). The ELH Series consist of a programmable controller for constant precision control and uniformity, and an integrated DewMaster chilled mirror hygrometer for accurate temperature and humidity measurements.
-
Product
Thermal Shock Test Chamber (3 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Divided into a high-temperature zone, low-temperature zone, and test zone. The test product is placed in the test zone, and the temperature from the high-temperature zone or low-temperature zone is applied to the test zone for thermal shock. The test product remains static during the test.- Equiped with a touch-screen control interface for easy operation.- Temperature is transferred to the test zone using a wind route switching method to perform thermal shock testing.- The maximum duration of high-temperature or low-temperature shock can reach 999 hours, and the maximum cycle period can reach 9999 cycles.- The system can operate in automatic cycle mode or manually select specific shocks. It can be set to perform two-zone or three-zone shocks, as well as cold-to-hot or hot-to-cold transitions.- The cooling system utilizes a dual refrigeration system, providing fast cooling. Water cooling is employed as the cooling method.- Testing can be performed at room temperature.
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
High & Low Temperature Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
Constant Temperature Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
AGREE Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood have 13 process and 5 times quality control to ensure the accurate control of all details for AGREE Test Chamber, EES and vibration test chamber, Temperature humidity and vibration test chamber, Comprehensive test chamber, Agree chamber
-
Product
Rapid Decompression Test Chambers
CA-RD(H)
-
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
Product
Portable Laboratory Test Chambers, Temperature / Humidity Testing
G-8 Elite
-
Russells G-8 Elite Series temperature and temperature / humidity chambers represent one of our pre-engineered environmental chambers. This model has a chamber volume in 8 cubic feet or 226 liters. Russells G-Series Elite portable test chambers give you the features and accessories you need to keep your temperature and humidity lab tests running smoothly.
-
Product
Environmental Test Chambers
-
A system that enables users to manipulate the environmental conditions of an enclosed space to run controlled tests on a subject.
-
Product
Environmental Chambers
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Sand And Dust Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
Product
Halt Hass Chambers
-
HALT and HASS chambers from WEIBER provide extreme temperature & vibration capabilities used during the product design and manufacturing cycles to compress the time normally required to identify design and process weaknesses. HALT techniques are important in uncovering many of the weak links inherent to the design and fabrication process of a new product. HASS techniques are incorporated during the production phase to find manufacturing process defects that could cause product failures in the field.
-
Product
Environmental Test Chambers
-
Bionic Scientific Technologies
Environmental Test Chambers offer precisely controlled environment required in insect and biological research, electronics production (battery testing and PCB manufacturing) and polymer testing (plastic and rubber testing) etc. Designed ruggedly and fitted with technology advanced instruments, our environmental chambers are available from benchtop cabinets to complex large capacity walk in rooms. At Bionics Scientific, we design and manufacture environmental chambers or climatic test chambers matching with customer required specifications and supply them worldwide at factory price.
-
Product
Bench Top Temperature Environmental Chamber
-
Burnsco Environmental Test Chambers
Our compact bench top chamber is ideal for prototype testing, life testing, and quality and durability testing . Its small footprint and comparatively large volume make it ideal in labs where space is a premium.
-
Product
Altitude and Vacuum Chambers
A series
-
Bemco's acclaimed Altitude and Vacuum Chambers are designed to meet the need for a combination, easy to use altitude testing chamber, and ruggedly built vacuum processing facility. Today's modern A series chambers feature another Bemco first, a standard Brooks Automation, Granville-Phillips Series 375 Convectron Gauge Controller.
-
Product
UV Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
* UV test chamber simulates damaging effects of long term outdoor exposure of materials and coatings by exposing test samples to varying conditions of the most aggressive components of weathering – ultraviolet radiation, moisture and heat. * UV test chamber use fluorescent lamps to provide a radiation spectrum centered in the ultraviolet wavelengths. Moisture is provided by forced condensation, and temperature is controlled by heaters. Based on your testing sample’s size, We has two options uv test chambers for choice.
-
Product
Environmental Chamber
-
Qualitest Environmental Chambers are capable of simulating a wide range of temperature, humidity, and other environmental conditions. These environmental chambers are well-suited for use in electronic, military, and pharmaceutical quality assurance and reliability testing, as well as research testing and production processes.
-
Product
Automotive CVJ Dynamic Fatigue Test Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
Automotive CVJ Dynamic Fatigue Test Chamber by Simplewell
-
Product
Walk-In Chambers
-
Wewon Environmental Chambers Co, Ltd.
These chambers are typically used for testing or storing products that require a large capacity chamber.
-
Product
Compact Temperature Test Chambers
TJR
-
Specifically designed these benchtop and floor chambers to have a compact exterior yet an ample interior workspace to maximize valuable floor space. Temperature Range: -73C - 200 °C. Internal Dimensions: WxDxH (inches) 16 x 11 x 11.75.
-
Product
Tenney Walk-In Environmental Test Chamber
-
Tenney’s multipurpose environmental walk-in room is the perfect test site for everything from testing against humidity, temperature and various climate conditions. This walk-in chamber provides supreme temperature testing for large components and equipment. When your testing requires walk-in rooms, choose Tenney. Our test rooms feature automated process control, energy efficiency, and a vast range of features and options.
-
Product
Automated Corrosion Test Chamber
-
Thermotron's Automated Corrosion Test chambers combine the capabilities of a temperature-humidity test chamber and a salt-spray cabinet. Corrosion chambers eliminate the need to manually transfer products from one environment to another.
-
Product
UV Chamber
-
In PV modules, many different components are exposed to the sunlight. Therefore, the IEC 61215 defines a UV preconditioning test (MQT 10) to test whether these components can withstand the UV radiation of the sun. In our test chamber, the UV radiation is up to five times the sun intensity to accelerate the test, as requested in the UV preconditioning test.
-
Product
Process And Chamber Monitoring Software & Systems
-
MKS process and monitoring solutions feature real-time, web-enabled, hardware, software, and systems to support a variety of tools and processes. These solutions improve performance and yield while reducing tool damage and false alarms.
