Proto Boards
-
Product
CPCI or PXI MIL1553B & ARINC429 Board
MS 1700
-
The 1553 Board consists of dual Redundant 1553B Channel A & B and ARINC 429 Channels (6TX and 12RX).
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
DB37 DIN-Rail Wiring Board
ADAM-3937
-
Low cost universal DIN-rail mounting screw terminal module for DAQ cards with DB37 female connectorCase dimensions (W x L x H): 87.2 x 112.5 x 51 mm (3.4" x 4.4" x 2.0")To Be Used With PCI-1713U, PCI-1715U, PCI-1718HDU, PCI-1720U, PCI-1730U, PCI-1733, PCI-1734, PCI-1750, PCI-1760U, PCI-1761
-
Product
Modular Relay Board
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
Product
Extender Boards
-
VECTOR Electronics and Technology, Inc.
Extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged. This provides access to both sides of the test board.
-
Product
P104 LVDT/RVDT Measurement Board
73LD4
-
NAI’s 73LD4 is a PC104-compliant LVDT/RVDT Measurement Board with six separate transformer-isolated channels. The channels can incorporate up to six programmable LVDT/RVDT-to-Digital Tracking Converters in a stack-through module. Each channel is programmable for 2-, 3-, or 4-wire inputs that automatically range between 2.0 volts and 28 volts, so there is no need to purchase multiple boards set for specific inputs. Operating frequency between 360 Hz and 10 kHz can be specified. Each channel also produces differential incremental encoder (A & B) outputs with programmable resolution and a zero-degree marker pulse.
-
Product
PC/104 OneBank I/O Board
EMC²-KU40
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU40 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU40 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
6U VPX Single Board Computer
VPX6-187
-
Curtiss-Wright Defense Solutions
The VPX6-187 VPX Single Board Computer (SBC) is based on the NXP QorIQ P4040/4080 SOC multi-core processor. Available in versions with 4 or 8 cores running up to 1.5 GHz, and up to 8 GB of high-bandwidth DDR3 SRAM, the VPX6-187 SBC provides high-performance processing and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
Product
Timing Board #1
TIO-10 #1
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
Product
Compact PCI Processor Board
CP67002
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP67002 is a CompactPCI® processor board based on China local-manufactured Phytium FT1500A/4 4 cores ARM processor, with more than 10-year lifecycle. Designed with ARM V8 Architecture, 28nm process technology and fine-grained power optimization technologies, the CPU integrates 4 ARM cores with CPU clock speed up to 2.0 GHz. Combined with the maximum power consumption of 15w, CP67002 is highly applicable for making low-power-consumption solutions.
-
Product
ISA Data Acquisition Boards
A-823PGH/S
-
The A-823PGH/L is 12-bit multifunction analog and digital I/O boards for the PC/AT compatible computer. The A-823PGH/L offer 16 single-ended or 8 differential analog inputs, plus two channels of analog output with 12-bits resolution. In addition, The A-823PGH/PGL has 16 digital input, 16 digital output , and one timer/counter channel. The A-823PGH Provides gain of 0.5, 1, 5, 10, 50 ,100 , 500 , 1000 while the A-823PGL provides gains of 0.5 , 1 , 2 , 4, 8 . It has a maximum sampling rate of 125 k Sample/Sec., DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
Single Board Computers
-
At the heart of every system is the single board computer. Elma sells, supports and integrates the latest in Intel and Freescale based single board computers from industry leading partners including Artesyn Embedded Computing, Concurrent Technologies, GE-IP and Interface Concept, as well as a few other specialized boards. When integrated as one of our popular AppliPaks, the SBC becomes part of a tech refresh solution which includes operating system and driver integration, plus mezzanine I/O or storage to form a bundled assembly sold and supported by Elma.
-
Product
DAQ- Data Aquisition Boards
ETS Series
-
The ETS Series products are designed to create a simple "Go, NoGo" test platform that executes quickly and requires minimal Operator interaction. Low-cost alternative to traditional PC-based test equipment. Test Electronics sources and stocks a large variety of data acquisition and sensor boards to make your hardware build quick and easy. Develop your own embedded test system or use the embedded test systems we have developed.
-
Product
Breakout Boards
-
GrayStone offers a family of DIN rail mountable breakout boards in various connector to terminal block configurations suitable for use in automation panels, electronic diagnostics or other general electronic applications.
-
Product
3U cPCI I/O & Comm Board
75C3
-
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PCI Express A/D Board
AD14-500 Series - Dual 14 bit, 500 MS/s
-
The AD14-500 series has two 20-500 MS/sec 14-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 4GB/sec (500MS/s * 2 bits per sample * 2 channels). Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
PC104 MIL1553A & MIL1553B Board
MS 1701
-
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
Product
LVDS To DVI-D Converter Board
AX93221
-
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
Product
TMR Switch Sensor Demo Board
-
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
Product
Boards, Blades, and Appliances
-
Adax Signaling Controllers; DPI, IPsec and GTP Packet-Processing Accelerators for LTE, 3G and IMS; 1U and 2U Communications Appliances; and Security Gateways.
-
Product
PCI Digital I/O Boards
PISO-P8SSR8AC
-
The PISO-P8R8 is an 8-channel isolated input/output interface board for the PCI-Bus computers.The PISO-P8R8 provides 8 electromechanical relay outputs and 8 optically isolated inputs, while PISO-P8SSR8AC and PISO-P8SSR8DC can be used in various applications including contact closure, external-voltage sensing,external-switch sensing and loading switching and designed for one 37-pin D-Sub connector.It can be installed in a 5V PCI slot and can support true "Plug & Play"
-
Product
PCI Multifunction Board
PCI-1202H
-
The PCI-1202 series is a family of high performance data acquisition boards for the PCI bus. It features a continuous, 110KHz for low gain (40KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1202 family has the same hardware architecture as PCI-1802. The PCI-1202 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1202 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
3U VPX Processor Board
VP32001
-
LinkedHope Intelligent Technologies Co.,Ltd.
The VP32001 is a PC-compatible high performance 3U VPX processor board supporting the 2nd generation Intel® Core™ processor and the Intel® Series 6 mobile class chipset with up to 8 Gbytes of DDR3-1333 ECC SDRAM. The VP32001 features an XMC site and a range of I/O interfaces including two SATA600 channels, dual 1000Base-BX, RS232/422/485 and USB interfaces. The board provides a flexible PCI Express® (PCIe) backplane fabric interface that can be configured in several ways from eight x1 PCIe ports to a single x8 PCIe port making it suitable for use in both distributed systems and centralized switching systems as defined in OpenVPX (VITA 65). For rugged applications two VPX-REDI conduction-cooled versions are available, the VP32001-RCS is a VPX-REDI Type 1 Two-Level Maintenance conduction-cooled board and the VP32001-RCT is VPX-REDI Type 2. The board is suitable for a range of applications within industrial control, transport, aerospace, security and defense applications. To simplify integration many standard operating systems are supported.
-
Product
PCI Multifunction Board
PCI-1800HU
-
The PCI-1800/1802 (L/H) is a family of high performance data acquisition board with 5V PCI bus. The PCI-1800/1802LU/HU card has a universal PCI interface supporting both 3.3 V and 5 V PCI bus. All the members in the PCI-1800 family have the same architecture; they feature a continuous A/D acquisition function of up to 330 kHz for low gain (44 kHz for high gain) under DOS and offer two 12-bit D/A output channels, 16 digital input channels and 16 digital output channels. The PCI-1800 series provides 16 single-ended or 8 differential inputs while the PCI-1802 series provides 32 single-ended or 16 differential inputs. In addition, an amazing A/D channel scan function called “MagicScan” is provided for users to easily implement multi-channel analog data acquisition applications. The specific MagicScan controller takes out most works of getting A/D value such as selecting channel, setting gain, settling time, triggering ADC and getting data. Even in channel scan mode, it can have different gain code for each channel, and the sampling rate can still reach 330 kS/s totally. The PCI-1800 series is suitable for high end applications.
-
Product
Hall Sensor Board with I2C Interface
046-323
-
Version: +5V/60A +3,3V/15A +12V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
50-Pin DIN-Rail Flat Cable Wiring Board
ADAM-3950
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with 50-pin flat cable connectorCase dimensions (W x L x H): 77.5 x 146.3 x 51 mm (3.1" x 5.8" x 2.0")To Be Used With USB-4751/L, PCI-1737U, PCI-1739U, PCL-722, PCL-724, PCL-731
-
Product
VMEbus Board
IIB-429-VME
-
The IIB-429-VME provides 4 ARINC-429 compatible channels (2 receive and 2 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This VMEbus board has a 3U form factor. The IIB-429-VME is also available in a 6U form factor (IIB-429-VME-4C) with four times the functionality.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
PC/104 OneBank Board
EMC2-ZU2CG
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-ZU2CG to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-ZU2CG also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
