-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
785045-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V,based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
Group Pulse Generator
STT-EFT-5K series
-
Beijing KeHuan Century EMC Technology Co,.LTD
STT-EFT-5K series group pulse generator is designed to determine a common and reproducible basis for evaluating the performance of electrical and electronic product power lines, signal lines or control lines when subjected to electrical fast transient pulse group interference. The performance of the generator meets the requirements of IEC 61000-4-4 and GB/T 17626.4 standards. Application areas: industrial control, home appliances, medical electronics, communication electronics, components, automation control, etc...
-
Product
2 Ch, 32MS/ch, 1 GS/s, 250MHz BW, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS805
-
The TiePieSCOPE HS805 is a portable USB oscilloscope that combines a high sampling speed (1 GSamples/s on one channel, 500 MSamples/sec on two channels) with a long record of 32 MiSamples per channel. That allows you to capture long, complex signal patterns at full speed.
-
Product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
780173-01
Voltage Input Module
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
Product
Transmitter (Export Only)
SMB
-
The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
-
Product
Dual 10th Order Lowpass Filter
64-VBF
-
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
Product
HandyScope HS6-DIFF With EMI & SafeGround: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMEG-W5
-
The powerful capabilities of the WiFiScope HS6-DIFF-1000XMEG EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test.
-
Product
Non-Multiplexed High Speed Continuous Function Card Overview
-
This type of system can be designed with benefits of both the multiplexed amplifier-per-channel and transient recorder systems. Benefits of the non-multiplexed amplifer-per-channel system include: High Sampling Rates: With an ADC per channel, the sampling rate is not encumbered with considerations such as multiplexing and post-amplifier settling time.Superior Filtering: With an ADC per channel, digital filtering can be used to augment analog filtering to achieve better anti-aliasing performance with much lower effective sampling rates.Superior Phase Matching: Digital filtering provides much steeper, more predictable rolloff rates and phase characteristics than analog filtering with greater stability with time and temperature changes at lower cost.
-
Product
Digital to Synchro and Digital to Resolver Converters
Digital / Synchro Converter
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
Product
25-Watt AC/DC Power Supply
Model 56GS1
Programmable Power Supply
NAI’s 56GS1 is a 25 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
15W to 960W - Single Output
DPP Series
-
*Low Cost*UL 508 Listed*Convection Cooled*Conducted and Radiated EMI, Class B*Input Transient Protection, IEC61000-4*Conforms to EN61000-3-2 (PFC)*Three year warranty
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
28 Volt DC Shelf Manager carrier card with conformal coating
28V-SM-CARR-C
-
The 28VDC carrier card with confirmal coating provides all the connectors necessary for the monitoring and control functions of any Elma systems, and also the power supply filtering required by the noise and transients consistent with MIL-STD-704E.
-
Product
Test Equipment
-
Our Trans-Guard DCVBD meter provides a 1kV @ 1mA test signal for direct measurement of the DC breakdown voltage of a variety of transient protection devices/products to help identify protection products that may be defective or damaged.
-
Product
Gunshot Detection & Localization System
-
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
Product
IPM Drive
-
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Product
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865683-01
-
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9205, cDAQ-9171, and cRIO-9940 includes the NI-9205 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9205 features a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Additionally, the NI-9205 provides up to 60 V of overvoltage protection between input channels and common, and it is rated for 1,000 Vrms transient overvoltage protection.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779137-01
Digital Module
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
779516-02
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
Product
Time Frequency Analysis Function
OS-0527
-
This function can evaluate transient phenomena that were difficult to capture by FFT analysis, and display clearly time change of the frequency component while maintaining its frequency resolution . The OS-0527 is equipped with STFT (Short Time Fourier Transform) and Wavelet transform.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Pulsed IV-Curve Solutions
-
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Power ICs - MicroBUCK® - Voltage Regulator
-
*Highly integrated microBUCK POL solutions deliver high efficiency while reducing costs*Each family offers a large portfolio of high density parts with common pinouts, allowing designers to scale for the best combination of cost and performance*Our PowerCAD simulation tool allows users to select the appropriate microBUCK regulator and generate a full circuit schematic**For performance optimization and comparison purposes, the schematic can then be edited as required.**Once the basic circuit is created, the user can perform DC, transient, and start-up simulations with visibility of all the circuit node waveforms.**Following these steps, the PowerCAD 2.0 simulation tool generates a bill of materials (BOM) available for online ordering.
-
Product
Digital TV Spectrum Analyzer
DS2831
-
Fast Spectrum Analyzer: detect and troubleshoot ingress with exceptional sensitivity of -60dBmV @ 300KHz RBW. Color-Coded Persistence Test: find transient noise hiding under upstream bursty signaling, without disrupting service. MER Measurement: up to 47 dB MER with 48 hours of statistical recording with 1 second resolution. Analog TV and SC-QAM: troubleshoot typical analog interference and distortions as well as SC-QAM performance. Time-Domain EVS Measurements: uncover interference from LTE signals under downstream QAM carriers with no service interruptions.Characterize OFDM carrier performance and DOCSIS 3.1 cable modem performance.
-
Product
HandyScope HS6-DIFF With SafeGround: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XMG-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
C-Band DWDM VGA without Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4500 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4500 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
PXIe-4143, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit
782431-01
Source Measure Unit
PXIe, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit - The PXIe-4143 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4143 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4143 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
-
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
