1553 Interfaces
Mil-Std-1553 interfaces.
-
Product
Rugged MIL-STD-1553 Ethernet Data Logging & Acquisition Module
eDAQ-1553-FQ
-
Avionics Interface Technologies
(2) Redundant MIL-STD-1553 bus interfaces (Transformer and Direct coupled) - (2) 10/100/1000-BASE-T Ethernet LAN Interfaces with POE - (2)PCM Output (up to 20Mbps) - (1) RS-232 Serial Interface - Streams select MIL-STD-1553 bus data & parameters over Ethernet - Supports Data Logging, Data Analysis, and Flight Test Data Recording applications - Timestamp synchronization to IEEE 1588 and IRIG-B - Full MIL-STD-1553 Bus Error Detection - MIL-STD-810G Compliant - Small, compact package 6in X 1.9in X 1.5in
-
Product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
-
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
High Performance PCIe-GPIB Interface Card
82351B
Interface
Convert your PCI computer directly into an intrumentation control; install easily with plug-and-play configuration.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
4-Port MIPI Interface GMSL Video Capture Card
MIC-FG-4G
Interface
GMSL SerDes controller. Supports up to 4K, 30fps, quad channel. MIPI 4 Lane compliant. Power Over Coax. V4l2, Gstreamer, Python support on Linux.
-
Product
PXI CANopen Interface Module
Interface
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
Interface
R15-LPCIE
Interface
Abaco Systems Embedded Systems’ R15-LPCIE is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a low profile PCI Express module. Available in -40 to +70 temperatures (with relays) and -40 to +85 temperatures (without relays) with one or two dual-redundant channels. The R15-LPCIE includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Interface
RAR-PXI
Interface
Available in a range of configurations to match your needs, the RAR-PXI provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected two-wire, 32-bit protocols in a PXI compatible CompactPCI form factor.
-
Product
PXI Remote Control Interface Module
41-924-001
Interface
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, this PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
Product
Interface
3508 MMS ECM
Interface
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
Introduction to Graphical User Interface - Softpanel
61800 Series
Interface
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
Product
Interface
RCNIC-A2PAU4
Interface
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
Interface
RAR-PCIE
Interface
Available in a range of configurations to match your needs, RAR-PCIE provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols.
-
Product
Interface
RCNIC-A2PAX
Interface
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Interface
RCEI-530
Interface
Available in a range of configurations to match your needs, the RCEI-530 provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols. The RCEI-530 supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, time-tagging, error detection and avionics-level I/O discretes, with support for either 33 MHz or 66 MHz PCI interfaces.
-
Product
Smart Aircraft Interface Devices
webCS
Interface
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
Product
MIL-STD-1553 Data Acquisition Module for Ethernet Networks
eDAQ-1553
-
Avionics Interface Technologies
One or two dual redundant MIL-STD-1553 bus interfaces - Transformer and Direct bus coupling supported - Two 10/100/1000 Mbit/s Ethernet LAN Interfaces - Streams MIL-STD-1553 bus data in standard IRIG 106 Chapter 10 format. - Compatible with 3rd party recorders and telemetry tools - All captured MIL-STD-1553 bus data provided with timestamps - Full error injection & detection capabilities - Works with AIT’s Flight Simulyzer™ GUI Analyzer/Simulator software
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Avionics PXI Express (PXIe) Interface Card - Multi-Channel, Multi-Protocol, 1553, ARINC, WMUX Interface for PCIe
Interface Card
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
PCI Bus Interface
PCI-6713-4IP
Interface
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
Product
PCI-8532, 1-Port, DeviceNet Interface Device
781062-01
Interface
The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
Flight-Certifiable Avionics Interface
RAR15XC
Interface
The RAR15XC flight-certifiable avionics communications board delivers high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O. Its small XMC mezzanine form factor is easily integrated onto other compatible boards, like the SBC314C flight-certifiable single board computer.
-
Product
Rugged Aircraft Interface Devices
AB2-AID
Interface
The AB2-AID is ready to go with high-performance avionics I/O combined with valuable built-in features such as a 9-port Ethernet switch, Ethernet to serial bridge, and 8GB flash memory. All in a compact, rugged package for easier integration and longer life.
-
Product
Interface
RCNIC-A2PA-TB
Interface
The RCNIC platform is a high performance Thunderbolt 3 device for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
Interface Card
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
