Up Converters
Increase the frequency of a signal.
-
Product
OEM SOLUTIONS - Optical Switch Modules From 4x4 Up To 144x144 Ports
-
Polatis Optical Switch Modules (OSM) are high-performance, fully non-blocking all optical matrix switch modules with port counts from 4x4 up to 144x144. Versions are also available for "any-to-any" port connectivity, which enables new interconnection architectures not possible with traditional symmetric NxN switch matrixes. The modules are designed for easy integration by OEMs integrating all optical switching with network equipment and are designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Four Slot PXI/PXIe Full Hybrid ABex Chassis with up to PXIe x4 Connectivity on Each Slot
ABex PXIe Rack 04
Chassis
Ultra-Compact 2U ABex chassis with 4 slots. This variant is characterized by outstanding compactness and due to the directly integrated PXIe full hybrid backplane one achieves maximum performance at an attractive price. The first slot is reserved for a single slot PXIe controller. Either Konrad PXIe embedded controllers or MXI interfaces are supported.
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
PXIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 1 Channel
M4X.6630-X4
Arbitrary Waveform Generator
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
Product
Pan/Tilt Unit for Side-Mounted Payloads up to 70 lbs
FLIR PTU-D300E
-
The PTU-D300 E-Series supports any type of single or multi-part payload through a flexible bracketing system of top and/or side mounting. Easy to integrate, the PTU-D300 E-Series is an open platform that provides the flexibility needed while minimizing your development and integration effort. The PTU-D300 E-Series has been proven in a wide range of mission critical applications for positioning of cameras, lasers, antennas, or other instruments in both fixed and mobile environments.
-
Product
Spectrum Analysis For P50xxB Up To 44 GHz
S970907B
-
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
Product
Rechargeable Submersible Strobe up to 6000m
-
The Teledyne Bowtech ST6K, Xenon submersible strobes are self-contained, compact, high intensity xenon beacons, designed for use as a visual aid to locate submersible vehicles or instrumentation packages when they surface for recovery. They can also be used to mark underwater objects, vehicles, divers or work sites.
-
Product
Basic Pulsed-RF Measurements For VNA Up To 53 GHz
S970251B
-
Add pulsed-RF measurement capabilities to your P50xxB Streamline series vector network analyzer
-
Product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
-
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Up to 3.2GHz, DB9 Male Fibre Channel Loopback Tester
F9M-LPBK
-
This premium loopback tester support speed of up to 3.2GHz and certified to pass the eye-pattern test.
-
-
-
Product
Turn Key Laser and LED Sources with Picosecond Pulse and Repetition Rate up to 100 MHz
DeltaDiode
-
DeltaDiodes utilize laser diode and LED technology to generate short optical pulses over a very wide range of repetition rates and wavelengths. Optical pulses as short as 50ps can be generated at repetition rates up to 100MHz.
-
Product
12 Bit, 2 Channels 3 GS/s PCI Express Gen-3 Digitizer Up To 8 GB Memory
EON Express / CompuScope 123G2
-
The new ultra high-speed, high-resolution Gage digitizers series EON Express CompuScope offers sampling of 3 GS/s at two channels on a single slot PCI Express card and are available with various on-board memory depths from 2 GS to 8 GS
-
Product
2U MGX GPU Server, Up To 4x H200 NVL, H100 NVL Or L40s And 3x NIC And SmartNIC DPU For AI Training, Large Language Models (LLM).
SKY-622G4
-
High density NVIDIA MGX™ GPU system up to 4 x PCIe GPU with NVIDIA NVLink™ bridge support, 3x NICs and smartNICsProcessor: Dual Intel® Xeon 6 Processors, TDP up to 350WMemory: 32x DDR5 6400 MHz RDIMM,up to 4TB supports MCRDIMMStorage: 8x E1.S NVMe at frontPSU: 6000 Watt 3+1 power supply with 80+ platinum level certification
-
Product
PCIe 16 Bit Multi-Purpose Digitizer - up to 80 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5943-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Modulation Distortion For E5081A Up To 20 GHz
S960704B
-
The Keysight S960704B modulation distortion software application enables fast and accurate active device modulation distortion characterization under modulated signal conditions up to 20 GHz. The wide dynamic range and vector error correction of the ENA-X yield an extremely low residual EVM of the test setup, delivering a complete picture of your device’s signal distortion performance without test system interference. S960704B software measures EVM, NPR, ACPR, and decomposes linear and nonlinear signals by spectrally correlating input and output spectrum without needing to demodulate. Integration with the ENA-X measurement flexibility enables quick modulated signal distortion measurements along with traditional VNA tests.
-
Product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
-
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
Product
PXIe-1085, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis
783588-01
Chassis
PXIe, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis—The PXIe‑1085 features a high-bandwidth, all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, up to 80 MS/s on 8 Channels
M2p.6568-x4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family.
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 24 Channels
DN6.653-24
Arbitrary Waveform Generator
The generatorNETBOX DN6.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either up to 48 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
PXIe-1086DC, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis
787137-01
Chassis
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis - The PXIe‑1086DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086DC monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
Product
1U Rackmount Network Appliance Platform With Intel® Celeron® Processor J1900 Up To 2.42 GHz And 6 LANs
NA342R
-
The NA342R 1U rackmount network appliance platform supports the 22nm Intel® Celeron® J1900 quad-core processor (codename: Bay Trail). The x86-based network appliance NA342R supports 6 Gigabit Ethernet ports and aims to provide customers a powerful and cost effective network appliance for VPN, content filtering, UTM, network security gateway, and firewall solutions.In order to address the various network application needs, the NA342R supports one USB 3.0 port, one USB 2.0 port, one console RJ-45 port, and one VGA port. Two 2.5" SATA hard drive bays and one CompactFlash type-II socket are available for storing event logs. The network appliance also supports mainstream Windows® 7, Windows® 8 and Linux operating systems.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 8 Channels
M2P.6533-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Converter
CTD-2160
-
The STD-2160 converter is a device for continuous monitoring and protection of rotary equipment. STD-2160 measures, controls and records signals from sensors continuously through 16 channels.
-
Product
Binary to BCD Converter
BAC300
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
