-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
NI-5732, 80 MS/s, 14-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781658-02
Digitizer
The NI‑5732 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 80 MS/s. You can use the NI‑5732 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5732 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
-
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
Product
Wearable Wireless Adaptive Refractor
VisionFit SC
-
The VisionFit SC is an innovative, electronic, mobile and wearable adaptive refractor.It performs a subjective sight examination and effectively replaces both the trial frame and the manual/electronic phoropter functionalities. VisionFit SC enables examining in free posture. Subjective refraction can be performed with the patient in his/her usual working environment and posture.VisionFit SC does not require the control of the patient’s position making it ideal for non-cooperative patients. Thanks to its comfortable and small footprint, this device reduces the examination time and increases the peripheral vision.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
RF Adapters
SMB Adapters
-
The SMB adapter allows connection to the SMB server to perform all the common CRUD (Create, Read, Update, and Delete) based operations for files and directories.
-
Product
UXG X-Series Vector Adapter, Modified Version, 50 MHz To 20 GHz
N5192A
Vector Baseband Generator
The N5192A is part of the UXG family of signal generation products designed for threat simulation; simulate complex signal environments for radar/EW.
-
Product
44U (77") Insulated Bus Bar
BB-77-I
-
44U (77") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
WAN Adapters
FarSync Flex
-
The FarSync Flex USB adapters have been developed to provide industry trusted sync and async communications support for Linux and Windows systems with multiple line signalling modes.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
PXI 4 Slot BRIC 92x8 1-Pole Dual Analog Bus (2 sub-cards)
40-560A-021-92X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Managed Hardened Media Converter, 1000Mbps, 2xSFP, AC Adapter (Also Known As IE-Multiway 858-11121; Previously BB-858-11121)
IMC-574I-SFP-PS
-
Versatile 4-port media converterSupports SNMP for managementSupports a variety of SFP modulesWorks under an extended temperature rangeSupports OAM, VLAN, 1+1 revertiveProvides RS-232 CLI (command line interface) console port
-
Product
Low-Profile PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1 Rear Slot, Universal
P311
-
This product is recommended for Systems Integrators and OEMs only due to the non-standard "volume envelope" that is required around the host's PCI connector.
-
Product
3U CPCI To PCI 4 Slot Adapter
-
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
Product
Adapter Kit, 3.5 mm
83059K
Accessory Kit
The Keysight 83059K adapter kit includes the 83059A 3.5-mm male adapter, the 83059B 3.5-mm female adapter, and the 83059C 3.5-mm male to 3.5-mm female adapter.
-
Product
Isolation Adapter
-
For harsh environments and motor control applications where debug tools may be exposed to high voltage or ground loop potentials, Blackhawk offers two product models of galvanic isolation.
-
Product
PCIe Clocks: Time Signal Receiver For The PCI Express Bus
-
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express bus is software-compatible with other PCI implementations, the hardware of these PCIe plug-in cards is based on a different concept.Fewer lines are used for data transmission than, for example, with PCI plug-in cards - a high transmission rate is achieved by using a fast serial protocol.
-
-
Product
32-bit / 33 MHz PMC to PCI Adapter
4933
-
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
-
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention. The EXC-9810 supports up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-9810/Ax adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher). Please see multi protocol 8000 modules for additional information on protocols that can be added to this card.
-
-
Product
PCB Adapters - VTAC
-
VTAC comes in a right angle PCB configuration which is ideal for a variety of applications that require a PCB solution. Modular and compact, VTAC right angle inserts can be used with strain relief plates to relieve PCBs and to secure COTS connectors in place.
-
Product
Osprey ISA Q-Bus Adapter board
9476-Q-B
-
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
Coax Adapter
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
-
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
Product
Bus Interface
IP-1553
-
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
Product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 5 Bus Matrix Inputs
40-569B-125
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-125 is a 8 slot module fitted with 5 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
-
Product
RS232 I2C Adapter LowPower
-
*I2C frequency adjustable up to 100kHz*Maximum power consumption <5mA*Interrupt input for external events*Simple software interface (ASCII commands)
