Coaxial Switching
Route RF offering excellent signal repeatability and isolation.
-
Product
High-Power PXI Multiplexer Switch Modules
Switch Module
Our High-Power PXI Multiplexer Switch Modules are based on electro-mechanical and solid state relays capable of switching currents of up to 40 Amps. Each module supports one or more multiplexer channels between one input/output terminal and a selection of output/input terminals. To reduce through path resistance, most of these multiplexers do not include isolation relays.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
MCX Male to BNC Male Cable, 50 Ohm, 30 cm
188375-0R3
Coaxial Cable
MCX Male to BNC Male Cable, 50 Ohm, 30 cm
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A
40-192A-012
Switch Module
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
LFH200 to 4x50-Pin DSub Switch Cable (CH-CH Twisted), 60 VDC, 1m
779038-03
Switch Cable
LFH200 to 4x50-Pin DSub Switch Cable (CH-CH Twisted), 60 VDC, 1m
-
Product
Switch Probes
Switch Probe
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-442
Switch Module
The 40/42-860A-442 is a PXI/PXIe quad insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
HD BNC Male to BNC Male Cable, 50 Ohm, 1 m
784996-01
Coaxial Cable
HD BNC Male to BNC Male Cable, 50 Ohm, 1 m
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-C180-3
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
Microwave Transfer Switch
60-808-510-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 8 Slot BRIC 230x16 1-Pole (10 sub-cards)
40-560A-121-230X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe RF Matrix, 8x4, 100 MHz, 75 Ω SMB With Loop-thru
40-729A-101-L
Matrix Switch Module
The 40-729A-101-L (PXI) and 42-729A-101-L (PXIe) are 8x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI 4 Slot BRIC 276x4 1-Pole (3 sub-cards)
40-560A-021-276X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI High-density 512x4, 2A Matrix
60-553-004
Matrix Switch Module
These high-density single pole LXI matrix modules are capable of switching up to 150VDC/100VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI/PXIe RF Matrix, 8x2, 1GHz, 50Ω, SMA
40-750A-521
Matrix Switch Module
The 40-750A-521 (PXI) and 42-750A-521 (PXIe) are 50 Ω 8x2 RF matrix modules with SMA connectors suitable for switching frequencies up to 1000 MHz. They are part of a range of 8x2 matrix modules with 50 Ω or 75 Ω characteristic impedance with front panel mounted SMA, SMB or MS-M multiway coaxial connectors.
-
Product
Single 24x8 1-Pole High-Density PXI Matrix Module
40-520-202
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Switch Module
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-728-002-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI BRIC8 FIBO Matrix Dual 124x4 2pin brkout
40-592A-114
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
80/24 Channel SPST Plug-in Switch Card
1260-118/118A
Switch Card
The Astronics 1260-118/118A is an 80/24-channel, SPST (Form A) plug-in relay card for the Adapt-a-Switch™ platform.
-
Product
PXI 4 Slot BRIC 90x16 1-Pole (6 sub-cards)
40-561A-021-90X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2-Slot BRIC Matrix, 64x16, 1 Pole (2 Sub-cards)
40-558-201-64x16
Matrix Switch Module
The 40-558-201-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
TSP100 Switch Probes
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI 12-Slot BRIC Matrix, 308x8 2-Pole (14 sub-cards)
40-562B-322-308X8
Matrix Switch Module
The 40-562B-322-308X8 is a high density BRIC12 matrix module with a size of 308x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 55x16 1-Pole (5 sub-cards)
40-562A-021-55X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 276x4 1-Pole (3 sub-cards)
40-560A-121-276X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 368x4 1-Pole (4 sub-cards)
40-560A-121-368X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Slot BRIC 184x4 1-Pole Matrix (2 sub-cards)
40-560A-221-184X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
PXI/PXIe RF Matrix, 16x8, 300 MHz, 50 Ω, SMB
42-724-011
Matrix Switch Module
The 40-724-011 (PXI) and 42-724-011 (PXIe) are 16x8 RF matrix modules suitable for switching frequencies up to 300 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
