VXI Backplanes
A VXI compliant electronic circuit board containing circuitry and sockets into which additional electronic devices or other circuit boards or cards can be plugged. (www.dothill.com)
See Also: VXI Chassis
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
6U VPX – OpenVPX Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. OpenVPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
VXI Digital Multiplier
4152A
-
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
Compact PCI PICMG 2.20 Backplanes
-
Comtel Electronics offers the Serial Mesh Backplanes PICMG 2.20 High Speed mesh connections on ZD connectors (P4 area). Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.20 Spec.
-
Product
VXI Prototyping Kits For RF Modules, Analog And Logic Circuits
-
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
Product
3U OpenVPX VITA 66-67 Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
VME Backplane
VME J1
-
VECTOR Electronics and Technology, Inc.
Vector offers wide range of VME backplanes from 3 to 21 slots wide in J1 and J2 are 3U backplanes. All VME backplane boards are constructed from FR4 epoxy glass material and are assembled and tested. Press fit connectors are used throughout on all sizes.
-
Product
VXI Rev 4.0 Module Shield Kits
-
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
Product
Custom Backplanes
-
The backplane is quite literally the backbone of a successfully performing system. Excellent signal integrity design is critical to platform reliability. Building on decades of backplane manufacturing experience, Elma engineers are innovation leaders in high-speed signal processing design, developing some of the most sophisticated backplanes in the industry.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
VXI Chassis for Digital Test Applications
1263 Series
-
The 1263 Series includes medium-power (1263MPf) and high-power (1263HPf and 1263HPr) models that leverage all the features of the VXI 4.0 standard for performance that meets your most demanding test requirements. The 1263 series is ideal for digital test applications.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
-
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
-
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
Product
VPX/open VPX Custom - 2-Slot Custom 3U VPX Backplane
-
2 slot custom 3U VPX backplane with a dedicated PSU slot.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
PXI / PXIe Backplanes
-
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
Product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
-
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
3-slot ATX-supported 1U Butterfly PICMG 1.3 Bus Passive Backplane
FAB209
-
*Designed for PICMG 1.3 SBC*Compatible with AX61120TP chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot and one PCIe x16 slot
-
Product
Backplane Connectors
-
Offering a broad portfolio of backplane connectors that include SOSA aligned optical, COTS plus hard metric, VITA standard and high speed twinax interconnects. Our interconnect solutions address the requirements of mission-critical applications within commercial aerospace, space and defense market segments.
-
Product
9050 VXI - 50 Module Solution for VXI cards
-
The 9050 VXI Solution is designed for use with VPC's pre-wired interconnect adapters on the top tier and discrete wiring modules on the bottom tier. The receiver opens downward via hinges to give the user access to the instruments in the rack. A microswitch, which comes standard, allows for shut off any power going through the system before removing the ITA. Using a plug and play plate or a flange kit allows for easy mounting of the receiver to any 19” rack system.
-
-
Product
Multi-channel USB and Power Distribution Backplane
USBDR-8
-
Power worldwide with universal AC adapterDC power from 12V to 50V sourceInstall from 1 up to 8 channels per USBDR-8Daisy chain USBDR-8 to control up to 112 channels using just one USB portUSB 2.0 compatible communication Synchronize all USBPxx-S1 operation in tracking or dynamic control applications Operate on table top, wall mount, rack mount or DIN rail mount Optional DIN rail connection kit for mounting the USBDR-8 to DIN rail available Optional 19" aluminum rack mount plate available
-
Product
VXI Front Panel Kits - Blank Or Custom Panels
-
* Single-slot wide front panel is a bend resistant, aluminum extrusion with mounting holes and ejector slots.* Ejector handles have removable face plates for labeling the module.* Kit includes ejector handles, mounting hardware, one blank face plate, one face plate with VXI logo, and assembly screws.* Layout drawings and CAD design aids available for adding additional cutouts to the blank panels.
-
Product
3U VPX – OpenVPX Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. OpenVPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
1-Slot Power & Ground only 7U VPX backplane with aperture for VITA 67 in J3
1900002558-9001R
-
Power for 3.3V, 5V and 12V, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
