Smoke
-
Product
Diesel Smoke Analyser
VLT-E9200
-
The VLT-E9200 diesel smoke analyser measures the opacity of the exhaust gases of vehicles with diesel engines. It can measure if an engine comkplies with the EURO 6 standards. An oil temperature sensor and an rpm counter can be connected.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
Smoke Detection Sensor - UL Approved, TAA Compliant
ENVIROMUX-SDS-TAA
-
For warning of smoke. Photoelectric smoke detector. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Voltage Supply: 8-35VDC. Current Consumption: 200uA. Alarm Output: Relay (NO). Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL. TAA compliant.
-
Product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
TURBO AIR SYSTEM TEST KIT WITH SMOKE ADAPTER
TPT69700A
-
*Helps locate air leaks in turbo system components by plugging the output side of the turbo and the intake inlet*Air is applied through one adapter to show the presence of leaks within the system*Six pairs of stepped adapters to fit most turbo systems on cars and light trucks
-
Product
Smoke Detector Testing
-
Requirements for testing of smoke detectors vary by country, the common need is for a functional test where smoke, or simulated smoke, is introduced through the vents of the detector to the sensor.
-
Product
VLT Chassis Dynamometers for Diesel Smoke Testing under Road Conditions (CDST)
-
Diesel Smoke Testing by Free Acceleration Test is one! But how accurate is this Test? We all know that it is a not valuable test, but still better as none testing of Vehicle Diesel Engines. The results are not realistic in many cases. And not as good for the Engine we know.
-
Product
Smoke Density Tester
TF350
-
TESTEX Testing Equipment Systems Ltd.
Smoke Density Tester , is widely used for density determination of smoke from the burning or decomposition of plastics and building material, designed according to ASTM D2843 and GB/T 8627. Equipped with high accuracy PLC and colorful touch panel.
-
Product
Smoke Generator
Easysmoker
-
The Easysmoker® smoke generator is the ultimate system for odour, smell and leak detection in pipes, sewers, roofs and other ducts, both indoors and outdoors.
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Synthetic Aperture Radar Image Processing
-
L3Harris Geospatial Solutions, Inc
Accurately and reliably monitoring the Earth is critical to many geophysical and geospatial applications. However, most sensors cannot capture data at night or through clouds, dust or smoke.
-
Product
DC/AC Inverter 450 W
ODS-750-7281-T
-
DC/AC inverter with 450 W from Premium | input ranges from 9.5 - 15 VDC | output is 120 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
Radar solution for thickness measurememt of steel & metal
-
Our radar sensor solution determines the thickness and the thickness profile of steel plates, steel strips or steel slabs (up to 1600 °C hot) with an accuracy of up to ±10 µm on the roller conveyor. Thanks to robust radar technology, sophisticated signal processing and intelligent radar algorithms, OndoSense radar sensors achieve this high level of precision in thickness measurement even under the difficult production conditions of the steel industry with smoke, steam, dirt, vibrations, fire and extreme temperatures.
-
Product
Smoke Detector Tester
Solo 365
-
The fire industry’s most popular range of detector test equipment is about to get even better. Solo, the test equipment used world-wide to functionally test fire detectors has a new tester in its range – Solo 365. This exciting innovation provides fire safety professionals with an array of stand-out features which make for faster, simpler and cleaner functional testing of smoke detectors. Key features include automatic generation of smoke which ensures only the amount of smoke needed to activate the detector is produced – minimizing smoke wastage and eliminating the risk of detector contamination. In addition, Solo 365 is light in weight and has a slim-line design which allows easy access into tight spaces – making it possible to test detectors which are hard to access with other portable testers. In response to market feedback, Solo 365 features an LED torch which automatically illuminates when light levels drop, making for easy detector alignment and testing in dark environments. Smoke is generated via newly designed smoke cartridges which fit neatly into the rear of the tester. With no reliance on pressurised aerosol cans, the cartridges can be easily shipped and stored and are unaffected by new regulations, set for 2018, which will affect availability of some pressurised smoke aerosols.
-
Product
Emission Analyzers
-
The VLT-E8104 emission analyser measures the opacity of the exhaust gases of vehicles with petrol/LPG/CNG engines. The accuracy complies with OIML class 0. An oil temperature sensor and an rpm counter can be connected.If you connect diesel smoke cell VLT-E9210, this analyser is a fully functionsl diesel smoke analyser as well.
-
Product
UNIVERSAL FILLER NECK CONNECTOR
SMOKE30
-
*Creates an air-tight seal with any vehicles EVAP system, eliminating the need for searching for the EVAP service port*Capless fuel system adapter works with your smoke machine to test EasyFuel™
-
Product
Mid-Range Pan/Tilt Multi-Sensor
DefendIR
-
The Ranger® MS-UC DefendIR is an industry-leading mid-range thermal imager that can see in complete darkness and through a multitude of environmental conditions, including smoke, rain, snow, dust, and dense fog. The Ranger DefendIR is ideally suited for day and night perimeter security, maritime surveillance, and DHS/DoD applications. The ruggedized housing is environmentally sealed and certified to meet NEMA4X and IP66 specifications, standing up to the most challenging weather and temperature conditions.
-
Product
Radar solution for molten metal filling level measurement
-
With the OndoSense radar sensors, the fill level of liquid steel or aluminum can be measured contact-free with sub-millimeter accuracy, even at metal temperatures of up to 1600 degrees Celsius. Dust, steam, smoke, vibrations and strong heat radiation have no influence on the high precision and reliability of the radar-based molten metal level monitoring. Active cooling of the level radar is usually not necessary.
-
Product
Digital Dust Monitor
3443
-
The Kanomax Digital Dust Monitor – Model 3443 measures aerosol concentrations corresponding to PM10. The intake isolates the aerosol sample so that the optics chamber is kept sterile for improved reliability and low maintenance. The unit measures 0.1 to 10µm particle size aerosol contaminants such as fumes, dust, smoke and mists. It is battery-operated, data-logging, light-scattering laser photometer that gives you real time aerosol mass readings. It is also suitable for clean office settings well as harsh industrial workplaces, construction and environmental sites, and outdoor applications.
-
Product
DC/AC Inverter 450 W
ODS-750-7271
-
DC/AC inverter with 450 W from Premium | input ranges 9.5 - 15 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
Product
DC/AC Inverter 450 W
ODS-750-7286
-
DC/AC inverter with 750 W from Premium | input ranges 50.4 - 90 VDC | output 120 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
Product
DC/DC Converter 150 W
CQB150W-110S48
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 48 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Opacimeter for the Measurement of Diesel Vehicles
MO / MAHA OPAZIMETER | VP 135043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
Situational Awareness Camera
FLIR K1
-
The FLIR K1 is a rugged, compact thermal camera that serves as an extra set of eyes on the fire scene, allowing commanders, officers, and inspectors to quickly complete a thorough 360° assessment in total darkness and through smoke. With a bright, integrated flashlight, the FLIR K1 illuminates the scene to help the user steer and manage the crew more effectively. It also displays 160 × 120 pixel thermal images that help users gain additional situation awareness that is not possible with the naked eye.
-
Product
High Performance TIC 320x240 (3 Button)
FLIR K55
-
With a FLIR K55 TIC in hand, you can attack fires more strategically, maneuver through smoke more easily, and save lives. The K55 displays crisp thermal images on a bright LCD, helping you navigate better and expedite critical decisions. The 320 x 240 pixel IR sensor and FSX™ Flexible Scene Enhancement produce detail-rich imagery at a 60 Hz frame rate that keeps up with the action.
-
Product
Walk in Explosion-proof Chamber (Auxiliary Equipment)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Explosion-proof Chamber is mainly used to test the safety performance of lithium ion battery, battery pack. Prevent test operators and other test equipment from being burned and exploding. At the same time, the explosion-proof test chamber with the smoke exhaust system can discharge the smoke generated in the test to the outside.
-
Product
DC/AC Inverter 1500 W
ODS-1500-7117
-
DC/AC inverter with 1500 W from Premium | input ranges 77 - 138 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
Product
DC/AC Inverter 4000 W
ODS-3000-7177-T
-
DC/AC inverter with 4000 W from Premium | input ranges 77 - 138 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
Dust and Opacity Compliance Monitors
-
LAND has a range of opacity, dust, smoke and particulates monitors which are the most advanced available, using patented measurement technology to give high accuracy. The analysers (which comprise a transmitter and a reflector) are mounted across the stack, the optical measurement technique uses no moving parts, giving the highest possible reliability with very low maintenance.
-
Product
AID Box Camera
TrafiBot HD
-
FLIR TrafiBot HD combines field-proven video detection algorithms with advanced camera optics and powerful processing technology in a single box camera. TrafiBot HD (with 1920 × 1080 resolution) provides superior image quality, embedded AID analytics, as well as multi-stream encoding. TrafiBot HD’s advanced processing unit generates traffic data and incident detection information and thus supports traffic operators with alerts on stopped vehicles, wrong-way drivers, pedestrians, lost cargo, smoke, and traffic flow data.
