Fiber Inspection
-
Product
Fiber Lab Flex
-
The Fiber Lab Flex from M2 Optics is a unique platform designed to offer engineers with maximum versatility when requiring optical fiber spools for network simulation, latency, training, and other testing and networking applications.
-
Product
Fiber Optic/BNC Converters
-
The active receiver and transmitter require power while the passive transmitter requires a TTL signal that is capable of driving 75 mA.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-218-M62.5
Multiplexer Module
The 40/42-852A-218-M62.5 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
42-850A-114
Multiplexer Module
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Visual Visual Inspection Device
IP-3000
-
Our visual visual inspection device Inspection Pro IP-3000 is an inspection device that quickly and accurately inspects the mounting board, which is constantly evolving, and judge whether it is good or bad without omission.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-852A-418
Multiplexer Module
The 40/42-852A-418 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Fiber Optic Multiplexer
FAC1000/2000
-
The FAC 1000/2000 is a multiplexer oriented to multi-point communication with several devices using fiber optic. It provides one or two inputs and multiple outputs.
-
Product
Dimensional Inspection
-
Initial Inspection Sample Reports (ISIR's)• Production Part Approval Process (PPAP)• Capability Studies• Production Surveillance• Reverse Engineering• Third Party Arbitration• Will Provide Same Day Quotation With Part and/or Print• Immediate Service Available
-
Product
Post Wire and Die Bond Inspection Machine
IV-T3300
-
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
Product
Customized Semiconductor Wafer Inspection, Sorting & Metrology Equipment | Systems
Customized Solutions
-
Unique Needs? Need better wafer inspection throughput, accuracy, versatility? Need a wafer defect inspection expert who’s not a sales person? We’ve been providing complete semiconductor wafer inspection, sorter, and microscopes solutions to semiconductor wafer manufacturers since 1994.
-
Product
Entry Level GPR System for Concrete Inspection
StructureScan Mini LT
-
Geophysical Survey Systems, Inc.
The StructureScan™ Mini is GSSI’s all-in-one GPR system for concrete inspection. This handheld system locates rebar, conduits, post-tension cables, voids and can be used to determine concrete slab thickness in real-time.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, ST Connectors
42-852A-518-M50
Multiplexer Module
The 40/42-852A-518-M50 is a PXI/PXIe 8-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Fiber Identifier & VFL
-
Are designed to non-invasively identify continuous-wave signals in fiber optic cables. They are low cost, hand-held tools.
-
Product
Thick Film Inspection
785
-
For thicker coatings such as coal tars, extruded and tape coatings, the Model 785 has a range of infinite voltage settings from 1,000 to 15,000 volts.
-
Product
Optical Fiber 8×1 Switch
OFSW - 8 × 1
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-8×1 is a 8x1 prism optical switch. It can support 8 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-332
Switch Module
The 40/42-860A-332 is a PXI/PXIe triple insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Magnetic Particle Flaw Inspection System
-
This model can perform every kinds of magnetic particle flaw inspection in our unit. circular magnetization longitudial magnetization continuous magnetization, residual magnetization threading bar magnetization current induction magnetization, AC magnetization AC demagnetization DC magnetization, DC demagnetization.
-
Product
Inline Wafer Electrical quality Inspection
ILS-W2
-
the Ultimate Wafer Electrical Quality Inspection Unit for Wafer Inspection Systems
-
Product
Mini Fiber Tester (SC Type)
21-8682-00
-
The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
Diode Laser Systems and Fiber Lasers
-
The HighLight Series of direct-diode systems and fiber lasers are robust and easy-to-use. These systems have a proven track record in industrial materials processing applications.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 200m
778959-200
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, SC/PC Connectors
42-850A-214-M50
Multiplexer Module
The 40/42-850A-214-M50 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Magnetic Particle Inspection Systems for Non-Destructive Testing (NDT)
-
VERIFY SURFACE AND SUBSURFACE STRUCTURAL INTEGRITY IN: Industrial Crankshafts, Ferrous Parts, Aircraft Components, Landing Gear Components.
-
Product
Vision Inspection System
Vision Station
-
Design and manufacture vision inspection system for SOT, SOD, TO, DPAK, SOIC, TSOP, SSOP, QFN/MLP, ODFN and LED inspection.
-
Product
Thin Film SPY Inspection w/ Built In Jeep Meter
780
-
For thin film coatings the easy-carry and easy to handle SPY Model 780 speeds inspection time with its built in Jeep meter and various other time saving and comfort features.
-
Product
Semiconductor & Flat Panel Display Inspection Microscopes
MX63 / MX63L
-
The MX63 and MX63L microscope systems are optimized for high-quality inspections of wafers as large as 300 mm, flat panel displays, circuit boards, and other large samples. Their modular design enables you to choose the components you need to tailor the system to your application. These ergonomic and user-friendly microscopes help increase throughput while keeping inspectors comfortable while they do their work. Combined with OLYMPUS Stream image analysis software, your entire workflow, from observation to report creation, can be simplified.
