Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
High 1.73 (49.00) - 8.00 (127.00) High Performance Lead Free Probe
LFRE-1H-8
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
High Force DMA
DMA+ Series
-
*The new DMA+ series instruments are dynamic testing machines based on a innovative concept of one-piece high rigidity test frame.*They are dedicated to the accurate analysis of the viscoelastic properties of most advanced materials.
-
Product
Measurement Hardware
-
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 305gf
K100-D080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
XCITE 1200-2 Inertial Mass Excitation System
-
The Xcite 1200-2 Inertial Mass Excitation system provides a new dimension to structural testing. The ES-302 Exciter contains a 250 lb mass which is accelerated through a 2″ displacement by a hydraulic actuator. The 2,000 lb inertial force which is generated provides ample input to structures such as those shown below to perform low frequency seismic studies and high frequency rotating equipment analyses.
-
Product
NEXYGEN DF Force Measuring Software
-
The NEXYGEN DF software is an easy-to-use Windows based data analysis package for use with the digital force gauges and torque gauges. Your test results are presented in a spreadsheet format so you can analyse data and perform common mathematical and statistical calculations.
-
Product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-1I-7
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-1I40-10
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Installation Tester
M74
-
M74 measures Overall earth resistance, tripping time of RCDs type AC, Insulation and Continuity of earth and equipotential conductors according to the laws in force in private electric installations.
-
Product
Multi Function Tribometer
MFT-5000
-
The state of the art Rtec Multi Function tribometer Mft-5000 is globally regarded as the most versatile and technologically advanced tribometer. Manufactured at silicon valley, California it is used by several top labs, universities and industries. The tribometer offers next generation patented force sensors with ultra low resolution, highest speeds and wide environmental control range than any other commercially existing tribometer. The patented integrated 3D profilometer allows to analyse surface change vs time. The universal tribometer MFT5000 allows to create a comprehensive report on friction, wear, tribology and surface analysis.
-
Product
Custom Testing Solutions
-
Test and MeasurementEnable increases the robustness of your test and measurement solutions, thereby reducing errors and associated costs. Data Acquisition (DAQ)Enable defines and builds custom DAQ systems for automated measurements of any process or manufactured part. Control and AutomationEngineeringEnable ensures that your processes are programmed to be safe, effective and optimized for both speed and quality. Real-Time and Mission CriticalSystemsEnable develops dependable real-time systems and Hardware in the Loop (HIL) simulations for high-speed applications. Motion ControlEnable creates software for synchronized multi-axis robotic control of velocity, position, force and action. Machine VisionEnable implements software and hardware-based solutions for precise image analysis, data extraction and vision-guided machine control. R&D Systems/Product DevelopmentEnable’s team of engineers and scientists works with you to address and solve problems containing technical challenges and uncertainties. Electronic Test SystemsEnable programs and builds software and hardware-based solutions for accurate measurements, from DC to RF. Mobile App DevelopmentEnable enhances your systems by integrating custom iOS and Android apps. Web DevelopmentEnable enhances your systems by integrating desktop and mobile web frameworks using PHP, CSS and HTML5. Database DevelopmentEnable decentralizes your data storage to be online, secure and accessible from anywhere.
-
Product
Universal SOIC-to-0.600 [15.24] DIP Adaptor
Series 647
-
Universal SOIC to .600 [15.24] DIP Adapter. 44 pin adapter for mounting Aries Series 547 Universal SOIC ZIF (zero insertion force) Test Socket to .600 [15.24] DIP PCB layout. Consult Data Sheet No. 10015 for test socket information.
-
Product
Electrodynamic Shaker Systems
-
Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.
-
Product
Physical
-
This category covers test equipment for verification of resistance to heat, fire, tracking, mechanical stress, endurance, impact, force, torque, dimensional accuracy & similar related parameters as required by national and international safety regulatory agencies. These equipment are used to check Electrical WiringAccessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Many of these test equipment are common to many standards and are essential for routine test purposes.
-
Product
Steel Structure Analyzer
NOVOTEST KRC-M2 (Coercive Force Meter)
-
Steel Structure Analyzer NOVOTEST KRC-M2 is designed for measuring coercive force of metal products in accordance with IEC 60404-7 and is used for non-destructive testing of chemical-thermal, thermal and thermomechanical treatments, evaluation of mechanical properties and residual stresses.
-
Product
Analytical Services
-
Atomic Force Microscopy (AFM) allows for sub nanometer resolution imaging of surface topography and is able to quantify surface roughness at the angstrom scale. Our team can give you highly accurate measurements such as surface topography, dopant distribution, magnetic domain features, and a wide variety of other sample properties to give you the information you need to do great work.Park can provide measurements in the following areas:● Topography (surface roughness, grain size, step height, etc.)● Mechanical Properties (stiffness, etc.)● Electrical properties (capacitance, conductivity, etc.)● Thermal properties ● Magnetic properties These properties can be measured in air or liquid, depending on your needs.
-
Product
10 N Screw Flat Grips
-
10 N (2.2 lbf) screw flat grips are primarily used for tensile testing low force, soft materials such as yarn, paper, plastics, and cloth, in film or wire geometry. Grip faces are flat and rubber-coated, and the supplied coupling joints for the 10 N screw flat grips are designed for use on lower-capacity load cells.
-
Product
Electro Fatigue Testing Machine
EPS Series
-
Jinan Testing Equipment IE Corporation
EPS series Electro Fatigue testing machine are fast acting table-top testers ideally suitable for performing static and dynamic fatigue tests on a variety of materials and components. These electro-dynamic machines use a linear electric motor with an adjustable upper cross-head of a stiff dual column frame. The electro-dynamic actuator is connected to single phase power, which resulting in a clean low maintenance solution. With dynamic force capacities, the Electro Fatigue testing machines are used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastomeric materials and others.
-
Product
Border Surveillance equipment
-
Shoghi offers its new portfolio of products for its discerning customers all over the world in the field of border surveillance. Ensuring the security and sanctity of its borders is a prime task for any nation for the security of the nation. Prevention of incursion by hostile elements, militants, prevention of activities like illegal human trafficking, smuggling of narcotics, arms and ammunition are tasks performed by homeland or border security organizations. The integrated surveillance solution also can be effectively used by reconnaissance and observation units of mobile formations of the defence forces for their operational tasks.Border Surveillance products:-1.Electro-optic Cameras2.Portable Ground Surveillance Radar3.Mobile ELINT System
-
Product
Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
-
Product
Ergonomic Force Gauges
MSE100 Series
-
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
Product
Automatic Type Cupping Testing Machine
GWB-60C
-
Jinan Testing Equipment IE Corporation
The digital cupping tester is mainly used in the test of metal sheets and thin strips. The automatic cupping testing machine can test the plastic deformation performance of the sheets and thin strips. The automatic cupping testing machine meets the requirement of international GB/T 4156-2007 "Metal Material Sheet and Thin Strip Erichsen Cupping Test". Adopting a hydraulic clamping and hydraulic stamping composite oil cylinder, the cupping tester automatically shuts down when a test sample has crack, so as to facilitate the observation of crack. With peak value memorizing function, the cupping tester can automatically memorize the maximal stamping force and the maximal deformation depth. A turning type clamp ensures the convenient replacement, assembling and disassembling of a punch and a test sample.
-
Product
Atomic Force Microscopy
-
Bruker’s industry-leading AFM microscopes provide the highest levels of performance, flexibility and productivity, and incorporate the very latest advances in atomic force microscopy techniques. Applications range from materials science to biology, from semiconductors to data storage devices, from polymers to optics with measurement of nanoscale topography, nano-mechanical, nano-electrical and nanoscale chemical mapping.
-
Product
ICT Probes
-
ICT Probes - Test Center: 50 - 100 milsCurrent Rating: 3 - 5 ampsContact Resistance: 30 - 50 milliohmsSpring Force: 113 - 312 gf (4-11 oz)
-
Product
High Performance Linear Accelerometers
-
Columbia Research Laboratories
The sensors featured in Columbia's High Performance Force Balance Accelerometers offer extremely rugged, high performance accelerometers. These sensors are used in applications ranging from severe vibration and shock environments, to demanding missile and airborne applications and downhole well servicing applications. Columbia also offers high temperature and miniature High Performance Sensors.
-
Product
Strain Sensors
-
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
Product
Stand-Alone Test Fixture
MA 2011/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1000Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,00 kg
-
Product
Exchangeable Test Fixture
MA 2109/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
Product
Snap-Action Switches
-
Panasonic Automotive & Industrial Systems Europe GmbH
based on a completely new type of contact system. By using sliding contacts, an extremely high overtravel of 2.5mm is achieved at optimum contact force, which greatly simplifies the installation and adjustment of the turquoise stroke switch. Furthermore, the ASQ turquoise stroke switch is bounce-free and hysteresis-free. Thanks to its IP6K7 protection class, it is ideally suited for a great variety of industrial and automotive applications.
-
Product
Static Constant Loading Tester
-
Static Constant Loading Tester is mainly used to determine the resistance to the axial static constant load of plastic manhole. A constant force is steadily loaded on the axial direction of the manhole for the specified time, when the test is finished, observing the sample appearance (deformation, collapse, crack or crazing), determine the deformation in axial direction and calculate the deformation ratio of manhole. The machine is also suitable for ring stiffness test, flattening test, ring softness test of thermoplastic pipes.
