Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Precision Positioning stage
N-661
-
Physik Instrumente GmbH & Co. KG
Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation
-
Product
Load Cells
-
Force Logic UK provides high-quality load cells, load indicators, and force measurement systems for a variety of industries. All our load cells are manufactured in the UK, and have passed through rigorous quality control standards for precise and accurate measurement, load monitoring systems, and industrial weighing applications. They are suitable for the measurement of static loads and dynamic forces in tension or compression, our load cells cover a wide range of mechanical forces, from 1kg to 1000 tonnes.
-
Product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
-
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
ForceTest Force Measuring Software
-
AMETEK Sensors, Test & Calibration
The ForceTest software interfaces directly with your digital force gauge enabling you to automatically capture tests and graphs on a personal computer. Test results and graph can be monitored directly on the live screen in real time while the test is being performed.
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
Product
DC Hysteresis Graph Test System
DX-2012H
-
Automatic measurement of the demagnetization curve of permanent magnetic material such as ferrite, AlNiCo, NdFeB, SmCo, etc. Accurate measurement of the magnetic characteristic parameters of remanence Br, coercive force HcB, intrinsic coercive force HcJ and maximum magnetic energy product (BH)max.
-
Product
Force & Strain Measurement
-
Load cells, tank weighing devices, balances, scales, force gauges, torque sensors and strain gauges including diaphragm, dual parallel, linear, rosette, T-rosette, and torsion and shear types.
-
Product
Probecard testers
MANAGER
-
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
Product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-1H-7
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Peel Back Force Tester
PBFT
-
Precisely measure the peel back force of carrier tape to verify your packaging systems are within specification. Results can be printed and stored with the outgoing product.
-
Product
Vibrator Control System
FORCE-III
-
The Force 3 Vibrator Control System is the newest generation of vibrator control system. It is designed to control individual vibes, or synchronize entire fleets of trucks. Using GPS, or VHF/UHF radio, for its time base the Force 3 both starts the Vibrator and controls its sweep with unparalleled precision and accuracy.The Force 3 is equipped with the latest ADC chips for better sweep resolution, increased computing power for faster response, GPS for precise source location, 8 Gbytes of internal memory for integrated VSS and PSS data storage, and integrated Wi-Fi for easy data offloading.
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
Force Sensors, Controls & Switches
-
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
Product
Force Calibration
-
Trescal provides full Force Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Force Calibration services can be delivered at your site or at our lab. Accreditations for our force calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
RVM-I Rotary Random & Sine Shake
-
Capacity, non reactive mass: 5 lbs 2.3 kg, allows stacked drives to 5" above table Actuator force, with cooling, random/sine: 50/75 lbf - 68/102 Nm Actuator force, without cooling, random/sine: 28/40 lbf - 38/54 Nm Frequency ranges: Random 6 Hz to 2 KHz or 2 Hz to 500 Hz (Set by Controller) Sine 2 Hz to 5000 Hz Displacement at outer radius: +/- 0.5" max, +/- 7 degrees with furnished stinger Weight with Actuator: 88 lbs. 40 kg
-
Product
Smart Door And Window Sensors
-
The Smart Door and Window Sensors alert you to a problem even before a break-in occurs. Installed on the doors and windows of your choice, they can tell if someone is trying to force entry.They also detect when a door or window is opened suddenly and send an immediate notification to your smartphone. This saves you valuable time in the event of a break-in.
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
Spring Testers
-
Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
Product
Load Frames
Multiaxial
-
MTS multiaxial load frames deliver all of these advantages. Engineered for superior performance in a range of testing applications, these systems represent decades of industry expertise. They include a variety of servohydraulic load frame configurations that apply force along multiple axes simultaneously, replicating real-world materials and component service conditions with absolute precision and accuracy.
-
Product
Crane Weigher (Scale)
-
The PIAB Crane Weigher is a high accuracy all- weather instrument for force measurement in aggressive environment. The PIAB Crane Weigher is suitable both for in- and outdoor usage. Supply your PIAB Crane Weigher with PIAB Remote Read-Out Instruments for convenient display.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
Tackiness Tester
TAC1000
-
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
Product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
-
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
Product
Tensile Testing Machines
-
Is an intelligent tensile testing machine specializing in testing the mechanical properties of various flexible packaging materials. It is suitable for test the peel force, heat seal strength, tearing resistance, deformation, puncture resistance, open force, low speed unwinding force etc of plastic film, composite film, soft packaging materials, adhesives, rubber, paper fiber and other products.
-
Product
Radio Communications
-
General Dynamics Global Imaging Technologies
Every day around the globe, General Dynamics'' radios ensure planes land safely, isolated personnel are found, soldiers communicate securely and first responders have the communications they need to go where no one else can. Our radios are more than tools, they are lifelines. Building on a strong, 50-year legacy in RF communications and networking development for military, government and commercial customers, General Dynamics’ radio products and systems are trusted globally in air traffic control, Blue Force Tracking, search and rescue, line of sight communications, satellite and wireless, and battlefield communications applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Digital / Synchro Converter
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
Product
Grypper G80 / G80 LIF
-
*Package-size PCB footprint: Since the PCB footprint of G80 is identical to the package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*Low insertion force: Unique contact design reduces the insertion force required to insert and retain higher-ball-count packages safely and securely within the test socket*No lid required: The package snaps directly without a lid, enabling easy probing, scoping and troubleshooting the topside of the device*Excellent signal performance: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection
