Band-pass Filters
Refine signal, allowing transmission of only frequencies within a specified, continuous frequency band, while predictably attenuating frequencies above and below the continuous band.
-
Product
Bandpass Filters
-
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
Product
RF Filters
-
CTS develops and manufactures high-end radio frequency (RF) filters used by various technologies to block out or filter certain signal frequencies. In 1982, CTS invented the ceramic monoblock, and ever since, our ceramic RF filters have been setting the industry standard in terms of lowest insertion loss, attenuation /rejection/isolation, Q-factor, size, power handling, and transition slope. Our portfolio includes band-pass filters, notch filters, low-pass filters, delay line filters, diplexers, duplexers, and triplexers/multiplexers.
-
Product
Miller 400A
44500
-
Rugged, lightweight case - safe to use on wet ground. Weatherproof, even with lid removed - IP67 rating for dust and water intrusion. Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations. Resistance measurement range from 0.01Ω to 1.1MΩ . Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency). Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
Product
Diplexers
-
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
Product
Low Pass and Bandpass SMA Coaxial Filters
-
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
Product
SWITCHABLE FILTER BANKS
FLT-1 WB
-
Matrix Test Equipment Incorporated
The Model FLT-1-WB is our Wide Bandpass filters for measuringthe Video Carrier and the Composite Second Order Beatdistortion on both sides of the carrier.
-
Product
Precision Low-Loss Multiplexers
-
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
Product
Seismic Signal Conditioners
-
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
Product
Bandpass Filters
-
K&L Microwave provides bandpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
Product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
-
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
Noise Filter
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
Low-Noise Filter, 210 V / 3 A
N1298C
Noise Filter
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
Product
High Frequency Tunable Bandpass Filters
CTB Series
-
Tunable Ranges Up To 8 GHz. Bandwidths 1% to 5% of Tuned Center Frequency. Digital Control Offered in Various Inputs, including GPIB (standard), RS-232, RS-422, and USB. Custom Interfaces Available.
-
Product
Waveguide Bandpass Filters
-
More details on PE-W28F001 WR-28 band pass wave guide filter can be found on the the waveguide bandpass filter design datasheet specifications up above. WR-28 waveguide bandpass filter from Pasternack is in stock now at our Irvine, CA facility. Our waveguide bandpass filter with WR-28 flanges is part of over 40,000 components for RF, microwave and millimeter wave applications in-stock which are available to ship same day worldwide.
-
-
Product
Filters
-
In order to minimize filter roll-off, we start with a quality, highly polished substrate and apply layers of metallization within tight tolerances. Our highly anisotropic ion beam etching process enables us to produce features down to 10 microns. Furthermore, the milling process yields a high consistency from circuit to circuit meaning that whether we produce 1 or 100,000 filters, each one will have consistent filter roll-off characteristics.
-
-
Product
Broadcast Filters VHF TV
-
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
Product
DC Filters
-
This DC filter provides substantial noise reduction on DC power lines of up to 50V 9A. Filter provides noise suppression in both directions protecting your DC lines from noise generating by a particular piece of equipment or protecting your sensitive equipment from noise coming from DC power supply or other loads. DC filter provides noise suppression for both power lines – positive and negative, plus common-mode noise vs. ground. Filter uses plug-in terminal block for connections and mounting flanges for easy installation. Its rugged construction makes it easy to fit in many industrial tools.
-
Product
Filters & Switch Filter Banks
-
PMI offers the highest quality filters, switch filter banks, filter assemblies, diplexers, multiplexers for industrial and military applications in the frequency range of DC to 40 GHz. All PMI’s Switch Filter Banks use PMI’s proprietary Solid-state Switch designs, which offer high speed and improved performance. While there are many standard models, PMI can design and build to meet your specifications.
-
Product
Highpass Filters
-
K&L Microwave provides highpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
Product
Tunable Filters
-
Our Tunable Filters can be used in a wide range of applications from R & D to production. We have both Gaussian, using dielectric multilayer coatings, and Flat-Top, using gratings, filter profiles available.
-
Product
RF Filters
-
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
Product
Wireless Filters
-
K&L Microwave offers a variety of wireless filters for the communications marketplace, built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on an existing design or to provide specifications for a custom design.
-
Product
Capacitor for DC Filtering
FIL1
-
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple and protect the line from instantaneous peaks and surges of tension.
-
Product
Anechoic Chamber Filters
-
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
-
Product
High-Pass Filters
-
is an electronic filter that passes signals with a frequency higher than a certain cutoff frequency and attenuates signals with frequencies lower than the cutoff frequency.
-
Product
Semrock Optical Filters
-
IDEX Health & Science offers a comprehensive line of Semrock optical filters. We set the standard in performance, quality, and reliability for the life science, point-of-care, clinical diagnostic, and analytical instrumentation industries. We have applied patented design techniques to create some of the most spectrally sophisticated optical filters on the market. Whether you select from our extensive catalog or we design a custom filter to your exact specifications, you can be confident of our uncompromising quality, reliability, and reproducible results.
-
Product
Gas Filters
-
WITT gas filters enable the finest filtering of impurities in technical gases such as acetylene, argon., oxygen, hydrogen, methane, carbon dioxide, helium, compressed air and ethylene. They thus protect downstream equipment and systems. Some gas filters are also referred to as gas cleaners.
-
Product
Broadcast Filters UHF
-
RFS Waveguide UHF filters are now 4th generation products designed for global combining and filtering applications associated with DTV and analog television transmissions.
