Circuit
-
Product
TTL/I2C/SPI Expansion Kit
OP-SB85L
-
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
Product
Massively Parallel Parametric Test System
P9001A
In-Circuit Test System
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
Product
Power Limiter, 5 MHz to 6 GHz, Type-N
11930B
Power Limiter
The Keysight 11930B limiter provides input protection for a variety of RF and microwave instrumentation. Failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage. The Keysight 11930B provides the same protection to spectrum analyzers and sources. At even greater power levels, failure mode for limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
Octocouplers
-
Panasonic Industrial Devices Sales Company of America
Panasonic's PhotoIC Coupler is a high performance optocoupler which consists of LED in input circuit, and custom IC in output circuits. PhotoIC Couplers are commonly used for high speed communication requiring physical isolation in various equipment and devices.
-
Product
In-circuit Test
i3070
-
The Keysight i3070 In-Circuit Test (ICT) System embodies proven technology, enhancing test efficiency through time-tested software, hardware, and programmability. Catering to diverse PCBA sizes, it addresses applications such as IoT, 5G, automotive, and energy. Its unique design minimizes undesired effects from parasitic capacitance, enhances immunity to crosstalk, and eliminates stray signal coupling, ensuring consistent and repeatable measurements.
-
Product
Precision Flying Probe Platforms For Automated Test Applications
-
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
Product
Voltage Detectors & Others
-
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
-
Product
RF Amplifier
SA831
-
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Portable Circuit Breaker Tester
PI-1600
-
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
Product
RTM Sensor Signal Conditioning Board
MS 3631I
-
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Cable Testers
-
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Product
Riser
-
Designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors.
-
Product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
RF Signal Generator
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
SMA Connectors
-
Pasternack SMA connector category contains a large selection of part numbers, the majority are RoHS and REACH compliant. SMA connector products in this category will terminate to coax, PCB (printed circuit board) or terminal and are built to precise RF and microwave industry specifications. Our SMA connectors are constructed in male or female gender in standard polarity, reverse polarity (RPSMA / RP-SMA) or reverse thread threads, with 50 Ohm impedance. Connector SMA series from Pasternack are available in straight, radius right angle or right angle versions, as well as, press in, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMA designs include clamp/solder, compression, crimp/solder, crimp/solder (captive contact), field replaceable, solder, solder (without contact), solder/solder or solder/solder (captive contact) attachment methods. We offer connectors in SMA series with standard or high performance levels manufactured with brass or stainless steel bodies. Other SMA connector options include quick disconnect (QD) or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMA connector series is in-stock. But not just in stock, also they will ship the same-day as they are ordered.
-
Product
Computer Networking Solutions
-
Today’s world has a never ending appetite for data. Everywhere you look there are connected devices that provide and consume that data at an astonishing rate, and the demand increases every day. Our computer and networking customers are constantly pushing the edges of technology to deliver data faster and more reliably than ever. They use the newest electronics available to keep our data flowing – data that is critical to the operation of the world’s infrastructure. As cutting edge technologies are developed, these faster more advanced capabilities require the most sophisticated testing available. Circuit Check is constantly evolving our test fixtures and systems to meet this industry’s most advancedrequirements.
-
Product
PSG RF Analog Signal Generator, 100 kHz to 9 GHz
E8663D
Signal Generator
Tackle demanding radar & satcom measurements with metrology-grade performance, including high output power & superior level accuracyUse as an ideal reference in phase noise test systems or for analog-to-digital converter testing with the lowest phase noise in a commercial sourceCharacterize devices & circuits by adding AM, FM, M & pulse modulation to your signalImprove existing test system performance: E8663D is built on the outstanding legacy of the 8663A & is fully code compatible
-
Product
Circuit Tester Set
TE6-0719
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Needle point probes*Continuity tester requires one AAA battery, battery not included
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
-
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
Product
JTAG Visualizer
-
JTAG Visualizer is an advanced graphical viewer and data management system for PCB schematics and layouts. Visualizer integrates seamlessly with the JTAG Technologies family of boundary-scan products, such as the ProVision application development platform, and accepts PCB data from a variety of CAD, CAM and EDA tools. In design Visualizer provides DfT (design for test) feedback to the user by enabling a graphical view of fault coverage on their design. In manufacture and test Visualizer can be used to highlight faulty nets (short circuits, opens, stuck-ats etc.) in both layout and schematics views.
-
Product
Optocouplers/Isolators
-
As safety products, optocouplers are designed to protect sensitive control circuitry or people from high voltages. They galvanically isolate the low- and high-voltage sides of a circuit by using an infrared emitter to transmit the control signal to a photo detector and reduce electrical noise coupling. Optocouplers from Vishay feature high isolation voltages, wide temperature ranges, and a wide range of output configurations to provide a perfect fit for your application.
-
Product
Power Management Controller
-
Macom Technology Solutions Holdings Inc.
Hghly integrated Power Management Integrated Circuit for GaN Power Amplifier
-
Product
Relay Circuit Tester
RCT76
-
Quickly identify electrical problems in an entire circuit at the push of a button. Test the component on a circuit to determine if it is functioning correctly.
-
Product
Digital Vision Microscopes
-
Sinowon Innovation Metrology Manufacture Ltd.
Video Microscope is widely used in the inspection of electronic industry production line, printed circuit board, weld detects ( such as wrong printing, edge collapse,etc)during printed circuit component, PC Board, VFD, and the identification of printing grid and painting, etc. It can display the zoom out image on the screen and save, magnify and print.
-
Product
Infrared Thermometer
6572
-
Peaceful Thriving Enterprise Co Ltd
6572 Infrared (IR) Thermometer is the non-contact way to make safe and quick temperature checks on mechanical equipment, electrical circuits and building systems while in operation. Regular monitoring of heat (infrared energy) emitted from surfaces can prevent potential problems and failures.
-
Product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
TopSpice 10
-
TopSpice is an affordable integrated computer-aided circuit design software package offering advanced native mixed-mode mixed-signal analog/digital/behavioral simulation based on the industry standard SPICE simulator program.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
RF Signal Generator
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
