Down Converters
Change a higher frequency signal to a lower frequency.
-
Product
Optical Path Converter
LS512A/LS512B
-
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
Product
Photometric Converter
C4000
-
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
Product
Thermal Voltage Converter
1395D
-
The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.
-
Product
Airborne Frequency Converter
AFC Series
-
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
Product
Data Converters
-
Omega carries an extensive line of data converters, including RS-232 to USB interface converters, fully isolated RS-232 to RS-485 converters, industrial ethernet to serial device servers, and more.
-
Product
RS232 to DMX Converter
DS232
-
RS232 to DMX Converter Controller Driver. Connect an RS232 terminal or computer port and drive DMX controlled dimmers and devices. A set of commands and auto fade rates offer power and flexibility for controlling DMX equipment. Use any RS232 terminal application to create command strings to: turn on, off, fade up, and fade down dimmer 256 DMX channels.
-
-
Product
AC High Voltage Break Down Tester
-
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
Product
Fuel Flow and Torque Converter
Model 44SM1
-
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
DC/DC Converter 12 W
RP12-11012DAR/P
-
DC/DC converter 12 W from Recom | input range 36 - 160 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +85 °C
-
Product
D/A Converters And Precision DC Source Instrumentation
-
PXI Arbitrary Waveform and Programmable Function Generators as well as DC source cards and a precision standards module.
-
Product
Current/Voltage/Frequency Converter
SCMA-VADC-710
-
The SCMA-VADC-710 current/voltage/frequency converter is switched between SensoControl measuring devices and hydraulic installations in order to capture the switching status of these components
-
Product
MACC Protocol Converters
-
Introducing the ultimate solution for effortless communication between different protocols - our state-of-the-art MACC II protocol converter.This powerful device allows you to easily translate messages between MIL-STD-1553, ARINC-429, Ethernet, Serial and more, ensuring compatibility and reliability in your aerospace and defense systems.With its advanced features and user-friendly interface, our protocol converter is the perfect solution for aircraft manufacturers, avionics designers, and military system integrators. It offers accurate and efficient data transfer, making it ideal for use in a wide range of applications such as aircrafts, ground vehicles, and naval vessels.Our protocol converters, both rugged, to withstand harsh environments, and standard, for the lab, are fully customizable to meet your specific needs. Its compact and lightweight design makes it easy to install and integrate with other systems.Don't let communication protocol limitations hold you back - Upgrade your systems today and experience the difference!
-
Product
Protocol Converter
MACC2
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
Signal Isolators & Converters
-
Devar current loop signal isolators reduce problems found in field measurements when signal transmitters or converters encounter both input and output signals that may be grounded. Current loop isolators eliminate these ground loops and are available as input loop powered or output loop powered instrumentation.
-
Product
Scalar Mixer / Converter Measurements
S96082B
-
The S96082B scalar mixer / converter measurements enables the highest accuracy for scalar conversion-loss / -gain measurements with a simple setup and calibration
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Converters
-
Schweitzer Engineering Laboratories, Inc.
These products convert between various communications interface standards.
-
Product
DC to DC Power Converters
-
CEHCO can supply DC to DC Power Converters. We offer customized solutions. The DC to DC Power Converters are from 1 KW to 200 KW.We need additional information from the customer as shown below:DC input voltage rangeDC output voltage rangeMaximum output current requirement and rangeOther requirements (ex: response time, ripple, remote control… etc)
-
Product
Interface Converter
ZET 7177
-
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
Product
Binary to BCD Converter
BAC300
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
-
Product
Auto Reversing Run Down Adapters
AURA
-
The AURA auto reversing run down adapters are designed to provide consistent and reliable torque readings for use with power driven torque control tools. The AURA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
Product
DC/DC Converter 150 W
CQB150W-110S15N
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output is at 15 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke | negative control logic
-
Product
Format Converter XMC
XMC-FC1
-
Curtiss-Wright Defense Solutions
Video integration is often complex and burdened with problems that arise from integrating legacy equipment with the latest video sources. The Curtiss-Wright XMC Format Converter (XMC-FC1) provides a flexible solution in an XMC format capable of converting between a range of video formats and resolutions. (15 different formats and resolutions are supported).
-
Product
Ethernet To Fiber Optic Converters (Multi-Drop)
-
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Photometric converter
HC 4000
-
Dedicated to optek turbidity sensors the HC4000 provides high precision signal processing combined with flexible configuration of the measurement setup. Several scales, like FTU or EBC can be selected to display the photometric signal in common units with product and process control.
