Electromagnetic
See Also: Electromagnet, Energy, Electromagnetic Simulation
-
Product
Magnetic Flaw Detector
CDX-Ⅲ
-
magnetic particle flaw detector is the self-designed magnetic participle flaw detector of MITECH CO.,LTD. With small size, light weight, easy operation, multifunction in one unit. The detector can equip A, D, E O four types of probes to realize the functions of magnetic clamp detection, electromagnetic yoke detection, cross magnetic yoke detection, ring detection. It is the necessary detector to do quality control, safety check, life evaluation in the fields of petrol, chemicals, metallurgy, shipbuilding, aviation, railway etc
-
Product
Compact Accelerometer (Shock Meter)
AP2019
-
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
-
Product
High-speed Photodetectors
11HSP
-
Only gigahertz-bandwidth qualified components are used in those high-speed photodetectors. An impedance matched microstrip line is used to couple the diode's output to the output connector. A microwave quality SMA electro-magnetic wave launcher is used to couple the signal to the scope.
-
Product
Concrete / Soil Wall Moisture Meter
-
This is a precision instrument adopting HF electromagnetic waves to measure the moisture content ratio without damaging the object under test. It can be set depending on different building material to raise its measurement accuracy.
-
Product
Radiation Resistant Resolver
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bidirectional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
3D Guidance®
-
The 3D Guidance® electromagnetic tracking solution delivers exceptional performance and value for OEM image-guided interventional and therapy systems and medical trainers that require real-time navigation tracking capabilities. The 3D Guidance solution tracks 6DOF sensors that can be embedded into OEM instruments such as ultrasound probes, rigid and flexible scopes, and laparoscopic tools. Continuous in-vivo tracking is maintained through difficult anatomy, even when sensors are out of sight. Low latency and fast update rates ensure the most subtle tool movements are instantly tracked and visualized within the OEM host interface. The 3D Guidance solution is available in the driveBAY™ and trakSTAR™ configurations, as based on the Electronics Unit. The trakSTAR is a standalone desktop unit that connects to a direct power source. The smaller driveBAY fits inside the drive bay of a computer, OEM imaging cart, or medical trainer/simulator, using the host’s power supply. Both share the same tracking accuracy and reliability. The ready-to-use configuration facilitates cost-effective integration and speeds time to market.
-
Product
Electromagnetic Counters
MZ Series
-
Ultra-small, non-reset total counter. Low power consumption. Voltages:DC6V, DC12V, DC24V. Applications: fax machines, vending machines, printing machines, lease type machines, slot/game machines.
-
Product
Waveguide Twists
-
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
Product
Electromagnetic Radiation Analyzer
SEM-600
-
Beijing KeHuan Century EMC Technology Co,.LTD
Broadband Electromagnetic Radiation Analyzer SEM-600 can accurately measure various complex electromagnetic environments. The probe covers all frequencies from low frequency to microwave radiation. It can measure electric field strength and magnetic field by equipping different types of probes. Intensity (magnetic induction) and power density, it is also equipped with ordinary probes and other weighted probes based on human safety standards.
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
Product
Cable Fault Location Equipment
-
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
Product
Antennas
-
A specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
Product
GEOPHYSICS, SEISMIC, and ATMOSPHERICS RESEARCH RECEIVER
Type RAS-1
-
Called the RAS-1, the receiver is designed for ultra low and very low frequency scientific research work, including the exploration of low frequency emissions due to seismic and earth-quake activity, study of atmospheric phenomenon such as "whistlers", and low frequency Sudden Ionospheric Disturbance (SID) and electromagnetics phenomenon. The RAS-1 will receive signals from under 200 Hz. To over 250 KHz in both narrow bandwidth modes as well as broad badnwidth reception.
-
Product
Electromagnet
-
The electromagnet can generate strong magnetic fields for experimental applications. Depending on the required magnetic flux density and Equipment under test volume the air gap can be adjustedcontinuously. The magnet poles come with conical shape close to the test volume to improve accessability and to optimize the achievable magnetic flux density.
-
Product
Resolver Systems and Resolver Sub Systems
TDSM
System
Computer Conversions Corporation
The TDSM Series are low cost absolute encoders consisting of a size 11 electromagnetic transducer and a 2.6 x 3.1 x .6 conversion module. The outputs available are 12 to 16 bit binary format representing 0 to 359.99 degrees of absolute shaft angle input. The transducer reference supply is also included in the module which is designed for printed circuit mounting. A data transfer and data hold line are provided for simple computer or microprocessor interfacing. These features in addition to the latest digital circuitry techniques, make these encoders the best selection in today's applications where resolutions greater than 10 bits are required with ultra high reliability assured.
-
Product
Precision Impedance Analyzer (20Hz to 10MHz)
ST2839
-
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Vector Signal Generator
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
Product
Accelerometer
AP2038
-
Combination of high axial sensibility, intrinsic frequency, and shock resistance; Low sensitivity to electromagnetic fields; Feed voltage and current wide range; Low intrinsic noise level.
-
Product
Digital Coating Thickness Gauges
-
The Elcometer range of digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness measurements on almost any substrate, whether ferrous or non-ferrous. Dry Film Thickness can be measured on either magnetic steel surfaces or non-magnetic metal surfaces such as stainless steel or aluminium using a digital coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel. The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates.
-
Product
Waveguide Switches
-
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
Product
ESD Protection
-
Protection against electrostatic discharges (ESD) is part of EMC Immunity (Electro Magnetic Compatibility) requirements. It is the ability for equipment to properly operate in its electromagnetic environment by limiting the reception of electromagnetic energy that may cause physical damage. ESD can be either conducted under the form of a transient voltage or can be radiated due to its fast rising time: powerful harmonics will generate erratic behavior by the application by coupling with other signals. Printed circuit boards must be protected against the effects of electrostatic discharge.
-
Product
Radar Level Gauge
HRRD730 Series
-
HighReach Measuring & Controlling System Co.,Ltd
At The Radar Level gauge Antenna emits and Narrows at The Microwave Pulse. This Pulse propagates in Space AT at The Speed of Light. The When IT Encounters at The Surface of at The the Measured Medium, Part of the ITS Energy IS the REFLECTED the Back and Received by at The Same, Antenna. At The Time interval The Between the transmitted pulse and the received pulse is proportional to the distance from the antenna to the surface of the measured medium.Because the electromagnetic wave propagation speed is extremely high, the time interval between the transmitted pulse and the received pulse is very small (on the order of nanoseconds). It is difficult to confirm. The 90X series 26G radar level gauge uses a special demodulation technology To accurately identify the transmitted pulse and the time interval of the pulse is received to further calculate the distance of the antenna from the surface of the measured medium.
-
Product
Predicting Microwave and RF Designs Virtually
RF Module
-
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
-
Product
Whole Body EM Phantoms
EM - PHANTOM
-
Schmid & Partner Engineering AG
The POsable Phantom for Electromagnetic sYstems Evaluations (POPEYE) is an anatomically correct human phantom based on a torso shell w/ head with posable arms, hands and legs. This radio frequency (RF) human has been designed to meet the requirements for test configurations for which the effects of the body on the EM performance cannot be neglected, such as operating tablet and laptop computers and other body-mounted transmitters. With a simple adjustment (one tightening screw), the arms, hands and legs can be positioned accordingly for conducting simulations of any usage or operation (standing, sitting, arms raised, talking position, etc...).
-
Product
Ethernet Switches
-
The switches CXR Carrier Ethernet CE 2.0 allow easy and economical transition to 10 Gigabit Ethernet class operator while providing hardened features in temperature and electromagnetic immunity.
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
EMC Testing
-
EMI is emitted radiation and its effects – a phenomenon. EMC is a device’s ability to limit the levels of unintentionally emitted EMI (that can harm other devices) and also a device’s ability to operate normally when subjected to EMI. Therefore, EMC testing seeks to ensure that a product possesses the characteristic of Electromagnetic Compatibility (EMC): the ability to limit creation of EMI (Electromagnetic interference) and the ability to operate properly when subjected to EMI. Stated differently, EMC testing measures the level of EMI control found in a device, and therefore helps to ensure that unwanted effects are prevented.
-
Product
Digital Thickness Gauges Paint Gauge Meter
HC-200
-
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc. ,both in the laboratory and in the engineering field. It can measure the thickness of nonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
