Analog Input
measurable voltage value.received from a sensor.
-
Product
8-Ch, 24-Bit, 25.6kS/s, Quarter Bridge Input IDAQ Module
iDAQ-873
Data Acquisition Module
High resolution (24-bit)Quarter-bridge supportedSynchronization along with other iDAQ modulesMultiple trigger modes for flexible configured acquisition timingBuilt-in digital filter for higher SNR
-
Product
Oscilloscope, 200 MHz, 4 Input Channels, 1 GS/s interleaved, 7 Mpts/Ch
T3DSO1204
Oscilloscope
200 MHz, 500 MS/s per Ch, 1 GS/s interleaved, 4 CH, 14 Mpts/Ch DSO with 7" Color Display.
-
Product
Oscilloscope 40 GHz, 4 Channels, 1 mm Inputs
UXR0404BP
Oscilloscope
UXR0404BP Infiniium UXR-Series is the 40 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
-
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
Product
Mixed Signal Oscilloscope - 200 MHz, 2 Analog Plus 16 Digital Channels
MSOX4022A
Oscilloscope
200 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary WaveGen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
LXI Reed Relay Matrix - Single 32x16 Plugin, No Direct Y Access, 3 Analog Buses
65-225-102
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Analog Output
-
12- or 16-bit D/A resolution voltage or current output and up to 1 MS/s update rate are supported.
-
Product
WaveRunner Oscilloscope, 2.5 GHz Bandwidth, 4 Input Channels, 40 GS/s on 2 Ch Sample Rate
WaveRunner 9254M
Oscilloscope
2.5 GHz, 40 GS/s, 4ch, 64 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
WaveRunner 9254M-MS (2.5 GHz Bandwidth, 4+16 Input Channels, 40 GS/s on 2 Ch Sample Rate
WaveRunner 9254M-MS
-
2.5 GHz, 40 GS/s, 4ch, 64 Mpts/Ch Mixed Signal Oscilloscope with 15.4" Capacitive Display.
-
Product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8
-
The stackable K-AN8 is our cost effective solution to measuring analog and digital/PWM sensors together in one module. Extremely easy to use and stackable with all of our other K-series instrumentation modules. The K-AN8 includes our unique power down and WakeOnCAN feature for quick installation on long term unattended fleet test vehicles.
-
Product
WaveSurfer Oscilloscope, 350 MHz Bandwidth, 4 Input Channels, 4 GS/s, 20 Mpts/ch - interleaved
WaveSurfer 3034z
Oscilloscope
350 MHz, 4 GS/s, 4 Ch, 10 Mpts/ch DSO with 10.1" Wide screen Color, Capacitive Touch Screen Display.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032T
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Infiniium V-Series Oscilloscope: 33 GHz, 4 Analog Channels
DSOV334A
Oscilloscope
33 GHz analog bandwidth4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Analog Output Module, 16-bit D/A
IP231
-
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O Module
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Telephone Line Testers for POTS / Analog Line
-
*This analog line tester is suitable for all instalers installing telephone equepement on POTS line.*Led indications signaling the status of analog line.
-
Product
IP + TVI + CVI + AHD+ Analog 5 in 1 Tester
-
*IP+TVI+CVI+AHD+Analog 5 in 1 CCTV. *4.3 inch capacitive touch screen. *Onvif/Hikvision,Duhua,etc more than 80 brand ip camera test.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, 10MHz RS-422 Inputs
APCIE-1711-10MHZ
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications can be realised through software adaptation.
-
Product
Analog Functions
-
Analog Devices designs amplifiers and linear products that deliver high performance and high value. We combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with US Type Connector
HSL-DI16DO16-US
Input/Output Module
*16-CH digital input and 16-CH digital output*Shrounded-type connector*Isolation Voltage: 2500Vrms*Higher output current up to 90mA/channel*Easy installation and wiring
-
Product
Oscilloscope: 350 MHz, 2 Analog Channels
DSOX4032G
Oscilloscope
The 4000 X-Series boasts 12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology and standard segmented memory.
-
Product
PXI Digital to Analog Converters
-
Keysight's PXI digital to analog converters and V/I sources are capable of supplying high and low voltages levels as well as source currents on one or multiple channels.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783126-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 8 GHz, 4 Analog Plus 16 Digital Channels
MSOS804A
Oscilloscope
8 GHz bandwidth4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
NI-9250, 2-Channel, 102.4 kS/s/ch Simultaneous, ±5 V, C Series Sound and Vibration Input Module
783827-01
Sound and Vibration
2-Channel, 102.4 kS/s/ch Simultaneous, ±5 V, C Series Sound and Vibration Input Module - The NI‑9250 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers and microphones. The NI‑9250 is also compatible with smart TEDS sensors. The NI‑9250 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Analog I/O module with 16 differential analog output channels
IO107
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with UJ Type Connector
HSL-DI16DO16-UJ
Input/Output Module
*16-CH digital input and 16-CH digital output*Higher output current up to 90mA/channel*Isolation Voltage: 2500Vrms*JAE 3-pin connector*Easy installation and wiring
-
