Calibration
maintains accuracy of test asset by correcting out of specification conditions.
See Also: Calibrators, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
Product
Bluetooth® Enabled Nitrate & Temperature Pen
UltrapenX2™ PTBT6
-
*Nitrate Concentration (ppm N or ppm NO3-) or mV*1 and 2 Point Calibration Options*Proprietary ISE Sensor Design*Built-in Double Junction Reference Electrode*Compatible with EPA Approved Standard Method 4500-NO3-D*Live or Hold Mode – User Selectable*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated Electronics*Waterproof*Powered by One N Type Battery (Included)
-
Product
LXI 75Ω RF Matrix - 1GHz
-
The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family. It maintains a close path loss match for all routes through the matrix, minimizing the calibration effort that has to be invested by users in optimizing their test system performance. The design is non-blocking Y to X (or X to Y) allowing any input to be connected to any output. The construction is based on high quality electromechanical relays which provide a fast operating time compared to microwave relays.
-
Product
Vector And Scalar Mixer/Converter Measurements
S96083B
-
S96083A provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers
-
Product
NIST Calibration for D410-A
D410-A-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Micrometers
-
A device incorporating a calibrated screw for accurate measurement of the size of components.
-
Product
Online pH Controller
LD-LOPC-A10
-
Online pH ControllerLD-LOPC-A10features 1 to 3 points pH calibration system, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. The automatic electrode slope display helps user decide when to replace the sensor.
-
Product
Single Phase Round Energy Meter Test Bench Type KP-S1000-C
-
Bofa Instrument & Equipment Co., Ltd
Single phase round energy meter test bench, type KP-S1000-C, is a special calibration equipment for testing Round (ANSI Socket type) energy meter and normal energy meter with bottom terminal block. It is an ideal testing equipment for energy meter factory or R&D institute, especially for testing ANSI Socket type energy meters. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
Acoustic Emission Calibrator
-
AE calibrator is similar to a simple signal generator, it can generate a variety of controlled waveform signal, different types, different amplitude and different frequency. It can help users calibrate acoustic emission detection equipment before acoustic emission detection.
-
Product
16/8 Channel 14 bit 500 MS/s Digitizer
VX1730 / VX1730S
-
The VX1730S comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1730S (previously VX1730) has also been upgraded, introducing a larger FPGA to accommodate more complex DPP algorithms and a new A/D converter for better stability which does not require temperature-related calibration.
-
Product
Field Strength Meters
FIM-22 And FIM-41
-
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their hinged covers, on the rugged drawn aluminum cases, contain a loop antenna. Opening the cover to a vertical position connects the antenna terminals to the receiver via maintenance-free gold-plated contacts. An interlock switch prevents inadvertent battery discharge when the cover is closed.
-
Product
Shorts
-
These coaxial shorts are useful to establish a reference plane, as well as providing certain protections from the environment. SMA shorts and Type N Shorts can establish reference planes. These coaxial shorts are not VNA grade but are often used at lower frequencies for calibration purposes. Included here are the following shorts: 2.4mm, 2.92mm, 2.2-5, BNC, N, SMA, SMB, SMP, SSMA, SSMC, TNC. Note, more options: 1.85mm is compatible with 2.4mm, 3.5mm is compatible with 2.92mm.
-
Product
Industrial Computed Tomography
TomoScope® XS
-
Coordinate measuring machine for three-dimensional measurement utilizing computed tomographyFast measurement with high resolution via the next generation transmission tubeReduce measurement time by 90% with OnTheFly TechnologyLow operating costs as a result of the new monoblock designExtremely precise air bearing rotary axis for low measurement uncertaintyLow space requirement thanks to compact designLow weight allows for installation almost anywhereFast amortization through low acquisition costsStandard-compliant calibration for reliable and traceable measurement results, optionally with DAkkS certificateVersatile fields of application such as plastic, metal and multi-material componentsSoftware for 3D real-time reconstruction of workpiece geometries during tomography
-
Product
Diode Power Sensor
8487D
Power Sensor
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Mobile sound Level Meter
SoundMeter
-
SoundMeter turns your iOS device into a handheld sound level meter (SLM) with support for exponential-time-weighted sound level (Lp) and equivalent sound level (Leq) measurements with various time and frequency weightings. The built-in signal generator tool can be used for generating calibration test tones, noise, chirps, or other periodic signals. SoundMeter also offers additional tools via in-app purchase, including a Noise Dosimeter and a whole or 1/3-octave real-time analyzer.
-
Product
Calibrator RTD Process Calibrator
VA720
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Calibrator RTD calibrator Source and measure 7 RTD type devices ( PT10, PT50, PT100, PT200, PT500, PT1000(385), PT100(JIS)).
-
Product
Portable Calibrators
Trig-Tek™ 41P & 45EMD
-
Portable Calibrator is a hand-held signal generator that provides accurate frequency and level in mV and pC
-
Product
Test And Measurement System
TM400
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
Multilogger
M1220
-
Universal datalogger with 4 hardware inputs. Two inputs for temperature-humidity probes and two inputs for thermocouples K, J, S, B, T, N. Multilogger can be installed permanently to Ethernet network or work as portable device. Included is traceable calibration certificate in accordance with EN ISO/IEC17025.
-
Product
NMR Permanent Magnet
PM1055
-
A secondary field reference for NMR testing and Hall teslameters calibration.
-
Product
Shield Level / Pathloss Equipment
PathTrax
-
Identical in form factor to the PAMS and PAMS-C, PathTrax provides an optimum solution for site surveys. Once the receiver is calibrated with the transmitter, the receiver measures path loss directly. PathTrax systems are available to cover several frequency bands each 75MHz wide, centered on 838 MHz, 860 MHz and 915 MHz. A PathTrax centered at 500MHz, covering 25MHz of bandwidth is also available.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8493B
Attenuator
The Keysight 8493B coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Calibrators
-
TES Electrical Electronic Corp.
Unique mapping function let you calibrate temperature. iCal is a multifunction calibrator and an arbitrary function generator.
-
Product
15-meter (49 feet) Sensor Cable
E1739C
Calibration Cable
The E1739C 15-meter (49 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System. Other cable lengths available: E1739A 5-meter (16 feet), E1739B 10-meter (33 feet) and E1739D 25-meter (82 feet).
-
Product
Coaxial Calibration Kits
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers the following types of calibration kits with a range of coaxial connector series for vector network analyzers (VNAs). All Rosenberger calibration kits can be used from DC to their maximum frequency. Full version with adaptors and sliding loads for variable measurements Industrial version for standard measurements LRL and TRL version
-
Product
FLUKE® Test Tools
-
Testwave LLC® has been selling, renting, calibrating and servicing Fluke Products for over seventeen years.
-
Product
ConFigXP
-
AMETEK Sensors, Test & Calibration
ConFigXP is free software to customize your XP2i digital pressure gauge to fit your application. You can add features and special modes, remove features to simplify the gauge, and complete password protected tasks, like calibration adjustment.
-
Product
PRO Portable Turbidity Meter
Mi415
-
Milwaukee MI415 PRO Turbidity Meter is for users demanding fast, reliable, repeatable results with ease of use. The Milwaukee MI415 PRO Turbidity features easy 3 point FNU calibration. The calibration points are 0, 10 and 500 FNU (Formazine Neophelmetric Unit). Calibration is automatic and fast with easy operation and a rugged meter design.
-
Product
Compact Electro-hydraulic Servo Universal Testing Machine
HLC series
-
Jinan Testing Equipment IE Corporation
HLC series single space Servo-Hydraulic UTM of Compact Type is designed for low capacity test. The single space compact type hydraulic universal testing system has rigid and compact design for testing the tensile, compression, bending, shearing and hardness of metal and non-metallic materials. Configured with extensive range of accessories for various applications, the hydraulic universal testing machine can provide the optimal testing solutions for your individual application needs. The single space Servo-Hydraulic UTM of Compact Type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
*Laser Power & Energy Meters
-
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
