High Frequency
High Frequency operating at 3–30 MHz.
-
Product
Metallic Probe Inductive Proximity Sensor
-
Shanghai Pubang Sensor Co.,Ltd.
1. All-in-one stainless steel housing design, strong anti-shock function2. Magnetic field interference, high switching frequency, wide temperature range3. Protection class IP67 (IEC)
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
Signal Generators
ZTX-Series
-
RPG's Signal Generator Extenders allow high performance frequency extension of microwave sources into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. These modules combine high test-port power with low phase noise to offer exceptional performance. Contact RPG to discuss Signal Generator Extenders configurations that will gain the best performance for your application.
-
Product
16-Bit, 12 GSPS, RF DAC and Direct Digital Synthesizer
AD9164
-
The AD9164 is a high performance, 16-bit digital-to-analog converter (DAC) and direct digital synthesizer (DDS) that supports update rates to 6 GSPS. The DAC core is based on a quad-switch architecture coupled with a 2× interpolator filter that enables an effective DAC update rate of up to 12 GSPS in some modes. The high dynamic range and bandwidth makes these DACs ideally suited for the most demanding high speed radio frequency (RF) DAC applications. The DDS consists of a bank of 32, 32-bit numerically controlled oscillators (NCOs), each with its own phase accumulator. When combined with a 100 MHz serial peripheral interface (SPI) and fast hop modes, phase coherent fast frequency hopping (FFH) is enabled, with several modes to support multiple applications.
-
Product
B-H Analyzer
SY-8218 / SY-8219
-
Soft magnetic components made of ferrite play an important role in electric components as they are used in a broad range of applications from low-frequency applications such as yokes for micromotors, to high-frequency applications such as flyback transformers, deflecting yokes, high-frequency transformers and magnetic heads. In actual operation, these magnetic components display characteristics different from DC magnetic characteristics or characteristics measured with an LCR meter.
-
Product
High DC Primary Current Injection Test Set
PDC15k
-
PDC15k High DC Primary Current Injection Test Set adopts high-frequency invert principle to realize the high DC current output capability, with very small size and light weight. PDC15k is modular designed with changeable modules and multi-functions local control software.
-
Product
Resonant Scanners
-
Electro-Optical Products Corp.
Resonant optical scanners are electromechanically driven oscillating devices that precisely deflect light beams with a sinusoidal motion. While their frequency remains fixed, scan amplitude can be controlled, offering exceptional repeatability and high-frequency beam manipulation. Resonant scanners are bearing-free and lubrication-free, ensuring stability, minimal power requirement, long life, and high reliability.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A10
-
IR Carbon and Sulphur Analyzer LD-LCSA-A10 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 20 to 100 seconds and a sensitivity of 0.1 ppm the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
Product
1203c Broadband RF Distribution
-
Precise Time and Frequency, Inc.
The ptf 1203C Broadband RF Distribution amplifier provides high performance frequency references for laboratory or system use.The ptf 1203C uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
Low CxR
-
Is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. A small flat-lead package has been provided which realizes a reduction in mounting area of about 50% compared withthe PS78xx series. It is suitable for high-frequency signal control, due to its low C × R, low output capacitance, and low off-state leakage current.
-
Product
Systems Integration for Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Artificial Power Supply Network
KH3762
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
PXI 4 x Changeover Switch 1GHz, 75 SMB
40-710-754
Switch Module
Model 40-710 RF switching card has a bank of 4 individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analysers.Available with a choice of connectors: SMA, SMB and Siemens 1.0/2.3 versions. BNC versions are also available with reduced bandwidth and 2 PXI slot occupancy.
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
QDRII/DDRII/ QDRII+/DDRII+ SRAM
-
DDR II / II+ (Double Data Rate) SRAMs and QDR^(TM) II / II+ (Quad Data Rate) SRAMs are the ideal memory devices for next generation networking and communications systems. These ultra-fast devices can support high bandwidth systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A11
-
IR Carbon and Sulphur Analyzer LCSA–A11 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and oxygen purity of 99.5 %, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
Product
Current Preamplifier
1212
-
The Model 1212 Current Preamplifier is designed as a low cost, gerenal purpose, benchtop instrument to provide a high performance detection system for small ac and dc currents. The 1212 operates with a virtual ground at its input which mitigates unpredictable high frequency rolloff due to input cables and stray capacitance.
-
Product
Manual Power Supply Network Manual
KH3766
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
Handheld spectrum analyzer/Signal analyzer
-
Recently, a lot of equipment have taken the high frequency or microwave technology according to the advancement and the spread of the telecommunication equipment. As a result, the handheld spectrum analyzer to analyze the signal by the frequency domain is necessaries now. The handheld spectrum analyzer is roughly classified into a heterodyne method and a Fourier transform method. The heterodyne method is also called the swept frequency method and makes it possible to measure up to tens of GHz though only for the steady signal. On the other hand, the Fourier transform method is also called the real time method and can handle an unsteady signal though the low measuring frequency range up to tens of MHz. As for our spectrum analyzer or signal analyzer, the MSA300/400 series adopts the swept frequency method, and the MSA500 series adopts both the swept frequency method and the Fourier transform method.
-
Product
Printed Circuit Products
-
Murata's board products include multilayer LCP products, Stretchable Printed Circuits, and iPaS™ products.Our multilayer LCP products have outstanding high-frequency characteristics. They are also thin and enable circuit design with freedom of shape. Our highly reliable Stretchable Printed Circuits can be stuck firmly to the body surface and remain affixed there securely. Our iPaS™ products are built in and integrated with capacitors and inductors. It is expected that these board products will contribute to the creation of new markets and new lifestyles.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
Test Contactor/Probe Head
cBoa
-
cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.
-
Product
RF Socket
-
With unparalleled technology, coaxial structure, and high-precision machining equipment, LEENO can provide RF test socket with high bandwidth, impedance matching and high frequency up to 40GHz.
-
Product
Standard 0.80 (22.00) - 4.00 (114.00) High Frequency Probe
CSP-03B-006
High Frequency Probe
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 3.70Return Loss @ -20dB (GHz): 1.80Dielectric VTE Rating (k VAC): 1Nominal Impedance (Ohms): 50Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,090Overall Length (mm): 27.76
-
Product
SMP Connectors
-
Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.
-
Product
Synthesized Clock Generator
CG635
-
Stanford Research Systems, Inc.
The CG635 generates extremely stable square wave clocks between 1 µHz and 2.05 GHz. The instrument''s high frequency resolution, low jitter, fast transition times, and flexible output levels make it ideal for use in the development and testing of virtually any digital component, system or network. Clocks from 1 µHz to 2.05 GHz. Random jitter <1 ps rms. 16 digits of frequency resolution. 80 ps rise and fall times. CMOS, PECL, ECL, LVDS & RS-485. Phase control and time modulation. PRBS for eye-pattern testing. OCXO and rubidium timebase.
-
Product
Passive Probe, 10:1, 200 MHz, 2-Pack
N2140A
Oscilloscope Probe
The Keysight N2140A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 200 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
Product
ElectroPuls
-
With more than ten years of running tests over billions of cycles, ElectroPuls systems are the established materials testing instruments using patented linear motor technology. Offering slow-speed static and high-frequency fatigue testing, this versatile testing capability means ElectroPuls systems are ideal for any lab or office space. Choose from axial only or combined axial-torsion systems that can deliver up to 10kN and 100Nm. Available in 3 sizes, simply pick the one that's right for you. ElectroPuls, a simpler, smarter, safer way to meet your testing needs.
-
Product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
Power Sensor
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
