-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Connector for Pickering
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
High Voltage 50 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female, 45º
40-960-160-F5
DIN41612 Female Connector
Suitable for users to create their own cable assemblies where a 45 degree down cable exit would be preferred. If the user requires the connector to have a second fixing then it can be fitted with an additional screwlock assembly 40-969-101 where applications permit.
-
Product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
Product
Low pin and internal configurable analog MCU
RL78/G11
-
The RL78/G11 microcontroller line-up concept is based on small packages like 20 to 25pin, in small 16KB flash memory and rich analog peripherals such as A/D converters, D/A converters, comparators and PGA and these are configurable as PGA+ADC+VBGR, PGA+CMP, CMP+DAC/VBGR, or PGA+CMP+DAC/VBGR. Using the smart features like DTC and ELC a lot of peripherals can be connected internally to reduce CPU workload and can save overall power consumption. It also supports very low power operation (100 uA @ 1 MHz ) and a high speed 4µs wake up. Available in small 3x3mm² WFLGA , 4x4mm² HWQFN and standard 20pin LSSOP, this MCU line is suitable for sensor application, Lighting/power sources and many small appliances.
-
-
Product
200 Pin D Connector Blocks for Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
8 Pin Power D-Type Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize an 8-pin power D-type connector.
-
Product
20 Pin GMCT Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 20-pin GMCT connector
-
Product
200 Pin D Cables - 200 Pin to 200 Pin for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
500 Pin SEARAY Connector & Cable Accessories
-
The 500-Pin SEARAY connector is used on switching products to provide a very high-density 2A connector solution that is suitable for use to 200VDC. We have developed a range of standard connection solutions to simplify the task of integrating the product into a test system. Due to the high density and skill levels involved in terminating this connector, we recommend the use of Pickering Interfaces solutions. Additionally, 1A connector and cabling solutions are also available.
-
Product
PIN Diodes
-
PIN photodiodes convert light to current – without a bias voltage having to be applied. Silicon is commonly used as an inexpensive detector material in the Vis range. For higher demands, InGaAs is used; it covers the widest spectral range from the Vis to the NIR. We offer silicon carbide as a “solar-blind” detector specifically for the UV range.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 0.5m, Exit Towards Pin 1
A050DM5-050DF5-0A050
Cable Assembly
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Standard Voltage 78 Pin D-Type Cables - Calibration Cables For Pickering Products
-
The cable assemblies below are suitable for use with Pickering precision resistor cards and modules that utilize 78-pin D-type calibration port connector.
-
Product
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553
510140197
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
510140194
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
-
Product
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB
540285010203
Cable Assembly
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB.
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Additional Products: 44 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Additional Products: High Voltage 50 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
13 Pin Towing Socket Tester ( For Halogen Light System)
7630
-
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
510140114
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 68 Pin Male VHDCI
540120010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 68 Pin Male VHDCI
-
-
Product
Additional Products: 15 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D To 25 Pin D-Type, Female To Male, 1.8m
A025CFR-025DMR-5A180
Cable Assembly
This 1.8m long female 25-Pin Micro-D to male 25-Pin D-type cable assembly is constructed from 18/0.1 (26 AWG) copper wiringwith PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Additional Products: 78 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
