VME Chassis
-
Product
cDAQ-9179, 14‑Slot, USB 3.0 CompactDAQ Chassis
783597-01
Chassis
14‑Slot, USB 3.0 CompactDAQ Chassis - The cDAQ‑9179 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements with the higher performance data streaming of USB 3.0. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9179 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
USB 3.0 and Ethernet to VME Interface
SIS3153
-
The SIS3153 is the successor to our SIS3150 USB2.0 to VME interface.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
VME sequencer
SIS3104
-
PCI Express and Ethernet to VME interfaceThe SIS3104 is the successor to the SIS3100 board.
-
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
Chassis Platforms
-
Elma offers a comprehensive range of standard, modified standard and custom packaging solutions with integrated backplane, power and cooling for; 19" rack-mount, test/development, and field deployable applications. Supporting the full range of VITA, PICMG and Small Form Factor architectures Elma has configurations based on VME, VME64x, OpenVPX, AdvancedTCA, CompactPCI, CompactPCI-Serial and COM Express.
-
Product
CompactPCI Chassis 3 Slots
1U 84HP
Chassis
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 3 slot 5V I/O 3U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
Product
14-Slot Chassis
ATCA CO14G4 DC 14 Slot 14U
-
The new flagship AdvancedTCA® 14-slot chassis, DC version is Comtel’s “4th Generation” and the latest in high performance platforms for ATCA. Its modular design offers ultimate flexibility to provide a solution tailored for your needs.
-
Product
5-Slot Desktop/Wallmount Chassis
IPC-6025
-
5-Slot Desktop/Wallmount Chassis with Scalability for 5U Multi-system Solution. Front handle for easy withdraw in rackmount carrier, Lockable front door prevent unauthorized access.
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
PXIe Chassis: High-Power, 18-slot, 24 GB/s
M9046A
Chassis
The Keysight Technologies, Inc. M9046A PXIe 18-slot chassis delivers the power and cooling required for high-performance applications with 3 PXIe hybrid slots and Gen 3 backplane (maximum 24 GB/s system and 8 GB/s slot-to-slot) with a two-link (x8, x16) system slot and x8 links to the PXIe slots
-
Product
Tower Chassis
-
The tower chassis series are IPC chassis featuring enhanced storage and high efficiency power supplies beneficial to Industrial server and application such as AOI. Tower chassis designed for micro-ATX / ATX / EATX serverboards to perform critical tasks.
-
Product
8-Channel VME LVDT/RVDT Scanner
V550
-
The V550 is a 6U, one-slot VME module which will acquire position data from up to eight LVDT (linear variable differential transformer) position sensors. The LVDT sensors are excited by an ultrastable synthesized sinewave generator, and conditioned by a precision 16-bit A/D converter followed by digital signal processing. The resident microprocessor supervises scanning and signal conditioning, and places updated position data in VME-accessible dual-ported data registers for instant access from the VME bus.
-
Product
16-Channel VME AC Power Analysis Module
V180
-
The V180 is a single-width VME module that allows accurate and comprehensive measurement of AC power circuits. The V180 acquires powerline current and voltage inputs using approved current transformers and model C750 remote potential transducers.
-
Product
Cost-Effective Wallmount Chassis
IPC-7132
-
Cost-effective Wallmount Chassis for ATX/mATX Motherboard and 10-slot Backplane. Support ATX/mATX M/B and 10-slot PICMG 1.3 backplane, Shockproof drive bay for one 5.25" ODD and three 3.5" HDDs. Thumb-screw for top cover easy opening, Bidirectional option to mount chassis on wall or workbench.
-
Product
1U Chassis
-
The 1U chassis support multiple configurations include SATA hard drives, rackmount chassis and redundant power supply that fulfill server-grade IPC standard. The 1U chassis series with the cooling fans design to deliver non-stop operation.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
6-Slot C-Size VXI Chassis
1264 Series
Chassis
The Astronics 1264C is a low-cost, 6-slot, C-size VXI chassis, designed and built with ISO-9001 certified quality. This chassis includes performance features normally found only in high-end, 13-slot chassis.
-
Product
VME Controller With USB-2 Interface
VM-USB
-
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
Product
9-slot Chassis
CH-09 AXIe-0
-
The 9-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
Chassis and Controllers Accessories
-
Keysight offers high-performance chassis and controller accessories to synchronize multiple Keysight USB modular products to accelerate your test system integration and development.
-
Product
64-Channel VME Analog Input Module
V230
-
The V230 provides high channel-count data acquisition for dense monitoring applications. The 64 channels are individually programmable for both input range and filtering. The three input ranges slightly exceed ±10 V, ±1 V, and ±100 mV, allowing confident measurements all the way to the end of common signaling ranges.
-
Product
Powered VME Crates
6U VME 6023
-
The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for standard VME/VME64 bus systems with 6Ux160mm cards.Designed primarily for applications in data acquisition, control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
SKYbolt II 9U VME
-
Delivering 64 GFLOPS of performance when fully populated, the SKYbolt II 9U VME motherboard is the foundation of SKY's VME solution, adding intelligent support for system services and high-performance data transfers to the carrier board for SKY's Merlin daughtercard containing compute processors, I/O interfaces, and global memory. A separate System Processor resident on the motherboard handles system overhead functions that would otherwise burden the compute processors.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
24-Channel VME Synchro/LVDT Simulation/Acquisition Module
V545
-
The V545 is a generalized- DSP-based sinewave processor intended for both simulation and acquisition of LVDTs, RVDTs, synchros, and resolvers. 24 generalized, isolated channels are provided. Each channel can be a signal source or a measurement input. Users can program any desired relationship between input and output channels, allowing simulation and measurement of a wide range of inductive transducers, using internal or external excitation.
-
Product
6U Mini Chassis
cPCI395
-
The cPCI395 mini crate series offers hot-swappable, redundant power supplies in 9 slots, compact but modular designed desktop / 19″ chassis. A front-side-plug high performance DC fan is used for cooling with front to rear air flow. One or two redundant operating plug-in 250W cPCI power supplies provide sufficient power for all applications.
-
Product
Chassis Position Sensors
-
Chassis height sensing is a specific application of CTS' rotary sensor technology. Chassis height sensors measure the position of the control arms relative to the frame or body of the vehicle. This information is used in systems such as headlight leveling and real-time-dampening. Key features of the CTS' chassis height sensors is the ability to mount in a variety of angles and projections to accommodate difficult packaging as well as robust sealing required for under chassis applications. With a global team of application engineers, CTS can package one of our generic, tooled for sales sensors or develop a custom product, unique for your application.
