Current Meters
Measure current using either "Average responding" meters reading linear loads or "True RMS" meters measuring non linear loads.
-
Product
Current Meters
-
Measure current using either "Average responding" meters reading linear loads or "True RMS" meters measuring non linear loads.
-
Product
Multiparameter Current Meters
MIDAS ECM
-
The MIDAS ECM is one of only a few multiparameter current meters that allow real-time operations over several thousand metres of cable, as well as autonomous deployment.
-
Product
NI-9227, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module
781099-01
Current Input Module
50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module - The NI‑9227 was designed to provide high-accuracy measurements to meet the demands of data acquisition and control applications. It includes built-in anti-aliasing filters. When used with a C Series Voltage Input Module, the NI‑9227 can measure power and energy consumption for applications such as appliance and electronic device test. You can not only measure and meter current and power but also look at quality factors such as noise, frequency, and harmonics.
-
Product
Capacitor Leakage Current/IR Meter
Chroma 11200
-
Chroma Systems Solutions, Inc.
The 11200 Capacitor Leakage Current / IR Meter is mainly used for electrolytic capacitor leakage current testing and aluminum-foil withstand voltage testing (EIAJ RC-2364A). The 11200 can also be used for active voltage checking or leakage current testing of absorber, Zener diode, and Neon lamp etc. With the standard RS232 interface, optional GPIB & Handler interfaces, high speed and stable measurement capabilities, the Chroma 11200 can be used for both component evaluation on the production line and for fundamental leakage current or IR testing for bench top applications.
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
High Accuracy Clamp Leaker
-
Leakage Current Clamp Meter, Car Standby Current Clamp Meter, Car Inrush current Tester, Car Charge Current Tester. It is specially designed for online measurement of AC/DC leakage current, current below 600V by adopting up-to-date CT technology and digital integration technology. It is especially suitable for measure car standby current, leakage current, inrush current. It is a product with the characteristic of relatively small size, high accuracy, strong anti-interference capability and automatic shifting.
-
Product
Require External Wireless Module
Flexible Coil Current Meter
-
One of the most advantages of the Flexible Coil Current Meter is external wirelessly connect to Smart phone / Tablet / PC to view data, record reading, capture picture with data on it and send the information to headquarter.
-
Product
Acoustic Imager
-
Can be used for quick on-site testing of current transformers in metering installations. They are designed and manufactured to test transformers’ primary current, secondary current, and turns ratio and identifies phase type and polarity.
-
Product
AC Current Clamp Meter
3280-10F
-
AC Current Clamp Meter with Broad Operating Temperature Range, Attachable Flexible Sensor, and Drop-Proof Durability
-
Product
Transformer Winding Resistance Meters
RMO TD Series
-
The RMO-TD Series On-Load Tap & Winding Resistance Analyzer is designed for the measurement of winding resistance of inductive elements, and for tap changer analysis. The RMO-TD series is based on the latest technology, using the most advanced switching technology available today. The RMO-TD series is accurate (0.1%), powerful (up to 60 A) and lightweight. It generates true, ripple-free DC current with automatic metering control and a discharge circuit.
-
Product
Bench DC Power Supply, Linear Regulation - Single, Dual Or Triple Outputs, Analogue Control, 30 To 130 Watts, Silent Cooling
EL-R Series
-
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
Product
IEC Standard Burden Sets (Current)
IEC Burden Sets
-
Testing and calibrating current transformers often requires standard burdens of reliable accuracy and stability, and burdens that are immune to stray fields and harmonics. These burden sets have been carefully designed to meet these requirements. They also provide the standard burdens required for the testing of current transformers for metering service, and for the testing (within the current rating provided by the sets) of current transformers for relaying applications, all as called for by IEC (International Electrotechnical Commission) Publication 185: 1987.
-
Product
Current Meter
Model 106
-
The Model 106 is the ideal instrument for coastal and estuarine applications and other light-duty survey work.
-
Product
Source Measure Units and LCR Meters
Source Measure Unit
Source Measure Units are high-precision, high-accuracy DC instruments that can both source and simultaneously measure voltage and current. Additionally, LCR Meters can measure the inductance, capacitance, and resistance (LCR) of electronic equipment.
-
Product
AC Power Source
SPS-100
-
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
Product
Hipot
AC, DC, AC and DC
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators with easy to read legend.• Continuously variable output from zero to full voltage.• Low end ground test.• Multi range analogue kV meter and current meter.• Fast acting overload circuit breaker.• Zero start interlock.
-
Product
Loop Meters
-
The CM-1TB + XL-1 are modern digital current loop-powered meters that convert standard loop current to engineering units. They feature high accuracy and a large 0.6-inch LCD display. Proven reliability combined with low cost has earned these meters world-wide acceptance, with thousands in use.
-
Product
Calibration Services
-
Mors Smitt has a professional calibration center. All electrical measurement equipment can be calibrated (for example; multimeters, current clamps, temperature meters, installation testers, power meters, safety testers, etc.).
-
Product
Precision Current Shunt
-
Has five precision selectable Ultra stable Current Shunts which ranges from 0.0001 to 1Ω. The Shunt T/C is less than 10ppm, and the internal current meter will measure from 1μA to 1000Amps.
-
Product
Test Equipment for Instrument Transformer
-
is desirable for measuring ratio errors and phase angles of low current (voltage) transformers used in electric devices, such as watt hour meters, smart meters, digital current meters, and transducers, etc.
-
Product
AC Line Splitter
1937
-
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
Product
Laboratory EM current meter / water level and wave height meter
-
ACM2-RS and ACM3-RS are 2-D and 3-D electro-magnetic current meters for laboratory experiments. The models provide digital output, a high-speed sampling rate and insusceptibility to electro-magnetic noise. ACH-600RS is a highly sensitive capacitance water level meters. With the new system, a maximum of four different sensors can be connected to the compact interface unit, enabling simultaneous recording on a personal computer. Additionally, the system can provide analog output as well as necessary. While conventional water level and wave height meters cannot be used near velocity sensors, our instrument can be as near as 5 cm without increasing noise, due to its special isolated circuit. The result is an innovative system that is capable of achieving highly accurate data.
-
Product
Bench DC Power Supply - Mixed-mode Regulation With Analogue Controls. Single, Dual Or Triple Outputs, 175 To 420 Watts
EX-R Series
-
Single outputs, 35V/5A, 18V/10A, 42V/10A, 20V/20ADual or triple outputs, 35V/4AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 5A (EX354RT)Compact design uses less bench spaceSilent fan-free cooling (not EX202R/EX4210R)DC output switches, automatic mode indicationRS232 or USB controlled models available (35V/5A single)Multi-mode dual model 2x(75V/2A) or 75V/4A or 150V/2A
-
Product
Portable Three Phase Energy Meter Test Set
SY3632
-
Hong Kong Songyang Industrial Ltd.
The SY3630 Energy Meter Testing Instrument is used to calibrate three phase, single phase, active or reactive energy meter under work, and also it can be used as voltage, current and power meter to measure AC parameter of three phase power line. Same as ZERA and MTE. Of course our price is very reasonable.
-
Product
Rogowski Coil
-
Rogowski Coils are mainly used to measure high current through the conductor. As opposed to conventional current transformers, Rogowski Coils are liner over wide range of current input. Rogowski Coils along with current meter are suitable for measurement of AC or DC current, up to a few thousand amperes. Ferrites India offers Flexible as well as hard Rogowski Coil which can accomodate wide conductor sizes.
-
Product
Touch (Leakage) Current Meter
LC-2R
-
The test for leakage current in mains operated equipmentis one of the most primary & important tests to verify thequality & electrical safety characteristics of products.
-
Product
Current Meter
MTD32
-
The mezzanine module (mezzanine) MTD32 is designed to measure instantaneous current values over 32 channels.
-
Product
Pressure To Current Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
-
Product
Analog Hipot & Insulation Tester
KT-5000Pi
-
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
Product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
-
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
