Product

LVDS (Low Voltage Differential Signaling) Drivers and Receivers

-

Analog Devices Inc.

Analog Devices Inc.

LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.

Product

LED Power Driver ATS

8491

-

Chroma ATE Inc.

8491 - Chroma ATE Inc.

1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series

Product

PicoBuck LED Driver

-

SparkFun Electronics

SparkFun Electronics

The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.

Product

Stepper Motor Drivers

-

STMicroelectronics

STMicroelectronics

ST's portfolio of STSPIN stepper motor drivers spans from relatively simple ICs with current control and phase generation to more complex solutions.

Product

LED Driver Automatic Test System

ATE-2

-

Lisun Electronics Inc.

ATE-2 - Lisun Electronics Inc.

•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.

Product

Dual Channel Driver Card

42460

-

Pulse Instruments

42460 - Pulse Instruments

Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.

Product

0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver

ADGM1304

-

Analog Devices Inc.

ADGM1304 - Analog Devices Inc.

The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).

Product

500 N Screw Flat Grips

-

Shimadzu Corp.

Shimadzu Corp.

500 N (110 lbf) screw flat grips are for use with low-capacity AGS-X series and EZ-X series load cells and come with flat grip faces. Similar to standard screw flat grips, these grips are versatile and are used for static tensile testing a wide range of materials, including rubbers, plastics, textiles, cloth, and paper, in film form.

Product

Industrial 4-20mA Driver

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.

Product

32 Channel Driver

-

Spectronix

Spectronix

The MultiChannel RF Driver is a 32 channel signal generator / amplifier intended to drive multchannel acousto-optic cells such as the Harris H-601.  The driver can be operated either as an RF amplifier, providing 32dB of gain or as a high power signal generator making use of a dedicated 1GSPS, 14bit digital synthesizer on each channel.  Modulation can be performed through the use of the internal source, external global input, external individual input, or programmable 16K sample RAM lookup table.

Product

Screw Jacks

-

Thomson

Thomson

Ruggedly designed and produced with high load-handling capacities, Thomson screw jacks can be employed individually or easily configured into a multitude of synchronized, motorized arrangements. These precise, highly efficient and long-life components are built to your exact specifications, making them ideal for industrial, automation, military and defense, and many other demanding applications.

Product

Dual Channel Clock Driver Card

PI-41400

-

Pulse Instruments

PI-41400 - Pulse Instruments

The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.

Product

LED & Driver Test Solutions

-

Chroma ATE Inc.

Chroma ATE Inc.

Chroma LED & Driver Test Solutions

Product

IVI Driver Package

IVI Development

-

Pacific MindWorks Inc.

IVI Development - Pacific MindWorks Inc.

The most complete IVI driver package from the most trusted name in IVI. Driver development can be tedious and distracting when you are scrambling to meet product deadlines. Researching the latest IVI standards, lack of driver documentation, and changing firmware all work against your product deadline. As a result, quality control over your product or driver or both can suffer. With IVI Development services from Pacific MindWorks you are free to focus on your product.