Alternating Current
Current Alternates direction of flow cyclically. Also known as: AC
See Also: Current, Direct Current, AC
-
Product
Auxiliary Potential Transformers
-
Osborne Auxiliary Potential Transformers (Aux PT’s) are used in utility and commercial industrial power systems. Osborne works with our clients to identify the safety advantages of using auxiliary potential transformers (Aux PT’s) to establish protection schemes for high voltage equipment. Aux PT’s step the voltage down to safer levels, normally below 600 V AC.
-
Product
Test Compliance
CTS Series 3.2
-
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.
-
Product
Tube Mount Transmitter / DIN Rail Receiver
-
The 28670XX-DRX Series are unidirectional wireless systems that comprise a transmitter and a receiver.This Drexelbrook transmitter accommodates two digital signals in the range from 5 to 30 V AC/DC or 100 to 240 V AC and one analog current signal (4-20 mA). These signals are available for further processing at the receiver in the form of two relay contacts and one 4-20 mA current output. In addition, a third relay in the receiver diagnoses the status of the wireless connection (RF link).
-
Product
AC and DC Non Inductive Current Shunt
Series A co-axial shunt and Option 02F/B shunt
-
Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift
-
Product
Adhesion and Peel Tester
-
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Product
Split type AC Current Sensor
CTF-5A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
AC Calibration Standard
1U647-001
-
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
Product
Guardian Ground Bond Tester
19572
-
Chroma Systems Solutions, Inc.
Wide resistance measurement range : 0.1 ~ 510 mΩHigh performance AC current output : 45 ACompact size ground bond testerProvide reliable and stable test resultsBuilt-in resistance compensation functionStandard RS-232 interfaceOptional GPIB InterfaceCompatible with the model 19070 series Hipot Tester2-Year factory warranty
-
Product
RF Terminators
-
Typically placed at the end of a transmission line and is designed to match the cable's AC impedance.
-
Product
ATCA CO14N AC 14 Slot 14U
-
The AdvancedTCA® CO14N 14-slot chassis, AC version suits most of the applications in the field. Its proven cooling and power architecture has been aided by a split backplane technology that allows to upgrade the signal backplane to the latest generation without any effort.
-
Product
High-Voltage Test Device
PGK 70/2.5 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Operation as DC or Ac testing device* Polarity of the DC voltage can be easily be reserved* Robust and durable
-
Product
110-125V AC GFCI Receptacle Tester
1934
-
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
-
Product
Current Probe With Hall Effect Technology
CP 35
-
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Resistance Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for resistors and potentiometers in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
AC Susceptibility
-
The AC Susceptometer option uses a small primary excitation coil to apply an AC field to a sample (typically 1mT at frequencies from 0.1 Hz 10000 Hz). A pair of secondary pick-up coils positioned close to the excitation coils are used to detect the sample response.
-
Product
AC / DC Combined High Voltage Test Set
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
Product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
-
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
Product
Fan Assembly Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing the performance of DC brushed and brushless motor, AC radiator, heater fan assemblies.
-
Product
Data Converter ICs
-
We offer a complete range of high-performance, low-power,and small-size data converter integrated circuits (ICs) for demanding industrial, automotive and consumer applications. Whether you need an Analog-to-Digital Converter (ADC), Digital-to-Analog Converter (DAC), digital potentiometer, AC and DC power and energy measurement device, voltage reference or a combinationof data converter ICs, we have the right solution for your application and world-class support to make sure you meet your design goals.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
RS-232 to RS-422 Interface Converter
Model 253
-
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-80H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High precision clamp type ZCT sensor*Big CT window,φ80mm*AC 0～10A*Least affection from the external magnetic field and residual current
-
Product
Three-Phase AC Power Source 320 Vrms, 3 KVA, 550 Hz
AC6903L
-
Keysight’s AC6900 Series three-phase power source provides a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
Digital Recorder
HiRES
-
HIGHVOLT Prüftechnik Dresden GmbH
The digital recorders HiRES are used to measure, store, and evaluate signals from up to 64 sources synchronously. Depending on the sensors used voltages, currents, temperatures, mechanical movements and various other signals can be measured. This measurement system features the ability to capture fast transient processes such as those occurring in impulse current tests on electrical devices or during switchgear testing. The system is also capable of measuring semistationary and periodic events such as DC voltage and AC voltage as well as superimposed semistationary, periodic and transient processes.
-
Product
PICMG 2.11 3U CompactPCI 47-pin Power Backplanes
cBP-3061/cBP-3062
-
- PICMG 2.0 CompactPCI Specification Rev. 2.1 compliant- Design for 47-pin 3U CompactPCI redundant power supply*- cBP-3061 for single power supply, cBP-3062 for dual power supply- AC (and DC) Screw terminal input
-
Product
Miniature Instantaneous Relays
CU-W Series
-
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads.
-
Product
Electrical Safety Testers
STW-9900 Series
-
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
Product
Megohmmeters/Insulation Resistance Testers
-
Full line of megohmmeters with test voltages 50V to 5000V. Capability to measure insulation resistance up to 10T. These rugged, weather resistant meters are accurate, reliable and built to perform. Battery, AC Powered & Hand-cranked models available.
-
Product
4U 5-Slot CompactPCI® Chassis with 400 W Power Supply
cPCIS-6400X Series
-
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width. The cPCIS-6400U provides 2+1 hot swappable 500W+250W redundant power supplies with universal AC input, while the cPCIS-6400X has a built-in 400W AC-input ATX power supply with cooling fan. Both series have PICMG 2.1 Hot Swap compliant 32/64-bit 5-slot CompactPCI backplanes and a PICMG 2.5 H.110 CT Bus.
-
Product
WINSTAT
-
This air ionizer is designed to remove static electricity in a wide range of industries, including ESD (electrostatic discharge) problems in the electronics industry and static countermeasures for plastic films. Air ionized by corona discharge in the discharge electrode is transported by a fan, neutralizing static electricity on charged objects located at a distance and preventing static electricity problems. The fan allows for static elimination over a wide area and long distances, and a wide range of models are available, including high-frequency, AC, and DC types, making it suitable for a wide range of applications, including equipment, desktop, and line use.
