Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
Helical Antennas
-
Is an antenna consisting of one or more conducting wires wound in the form of a helix.
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
Cable Assembly 44-Pin D-Type Male to Female, 2m
40-970-044-2m-MF
Cable Assembly
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
Product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Cut Ends, 5A, 1m
A050FFR-C-0A100
Cable Assembly
This is a 1m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A050DM4-C-0A200
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, Receiver, TriPaddle, 72", 200 Pin Male LFH, M3 jackscrews
540105040505
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 72", refer to drawing for wire list, M3 jackscrews
-
Product
Cable Assembly, 9-Pin D-Type Male To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-MU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Pin-Line™ Collet Socket with Wire Wrap Pins
Series 0503
-
Pin-Line Collet Sockets with Wire Wrap Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with wire wrap or solder tail pins. Consult Data Sheet No. 12013 for solder tail pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
Round Wire Coil Inductors
-
Round wire coil (RWC) inductors come in six platform sizes and enable the highest efficiency of any SMT inductor through the use of a low loss ferrite core material which minimizes AC losses and also eliminates thermal ageing. The use of round magnetic wire instead of rectangular flat coils enables a lower cost while still maintaining a low DCR and small footprint. The platforms have passed the AEC-Q200 stress test qualification proving the designs robustness and suitability to difficult environments but the parts are not IATF certified. The platform range from 7.6×7.4×6.4mm to 26x26x15mm and are suitable for a wide range of applications and markets including communications, computing and industrial.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
785186-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
-
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Linux
778686-01
GPIB Controller
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Ferrules, 5A, 2m
A050FFR-F-0A200
Cable Assembly
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 2m
A020GMR-C-1B200
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Contact Resistance Meter
-
4.5 Digits LED display Range : 0 TO 1999.9 W to 199.99mW High Measurement Current : 100A DC max. True Four wire resistance measuring technique eliminates lead resistance errors inherent in 2 wire systems. Fully protected against overloads. Proven design
-
Product
Lifecycle Support for Custom Product Development
-
The parts and components that are rooted in idea generation and product development are the ones that are most likely to succeed. Electri-Cord’s lifecycle support for the production and manufacturing of custom wiring harnesses, cable assemblies, power cords, and high-level assemblies incorporates a four-stage approach that covers the lifespan of the product. This custom product development process includes everything from design prototyping to end-of-life processes.
-
Product
4-Pin Power D-Type Female to Unterminated With Cut Ends
40-972-404-2m-FU
Cable Assembly
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A037DM5-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PXI RTD Simulator Module, 4 Channel, PT100
40-263-501
Simulator
The 40-263-501 is a 4-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
160-Pin DIN Female To 6-Pin Bare Wire Male Switch Cable
782417-01
Switch Cable
160 Pin DIN to Bare Wire Cable for PXI Switches, 1m
-
Product
12V SHORT BUDDY TESTER
SB230
-
*To find shorts, push or pull the offending wire and hear a loud beep*Features re-set/re-power capability for dead shorts to keep working hands free*Set amp levels at 10A, 15A, 20A, 25A and 30A
-
Product
4-Pin Power D-Type Cable, Male to Male, 2m
40-970-404-2m-MM
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
20V/30A/300W DC Programmable Electronic Load
TOB-IT8512
-
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector Without Backshell
C096SFX-XSP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
16-Channel Multiplexer (2 / 4-Wire) Module for DAQ970A and DAQ973A
DAQM902A
Multiplexer Module
DAQM902A 16 Channel Multiplexer (2/4-wire) Module. Reed relays with high voltage switching of up to 300 V and scan speed up to 250 ch/s.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
