Deposition
-
Product
Dynamic Ultra Micro Hardness Tester
DUH-210/DUH-210S
-
A new evaluation system for measuring the material strength of micro regions, such as semiconductors, LSI, ceramics, hard disks, vapor deposited films, and thin coating layers, not addressed by previous hardness testers. It can also be used to evaluate the hardness of plastics and rubbers. This instrument uniquely measures dynamic indentation depth, not the indentation after the test. This in turn permits measurement of very thin films and surface (treatment) layers that are impossible to measure with conventional methods. Additionally, this same method supplies the data needed to calculate elastic modulus on the test specimens.
-
Product
Handheld Ultrafine Particle Size Distribution Measurement.
partector 2 Pro
-
Naneos Particle Solutions gmbh
The naneos partector 2 Pro version is a further development of the well-established Partector 2. The Pro version of the partector 2 can additionally switch through different deposition voltage levels and therefore scan an 8-channel size distribution of an aerosol of interest.
-
Product
Deposition Systems
-
When a thin film requires the most stringent structural or compositional properties consistently across every layer, Veeco’s Ion Beam Deposition (IBD) technology is often the answer. Using a focused beam of ions to sputter material from a target, this physical vapor deposition technique builds dense, uniform films with standout adhesion and stability.
-
Product
Automated Stand for Magnetic Luminescent Control of Railway Wheels
-
The amount of information processed and time constraints required the creation of a multi-level distributed image processing system based on National Instruments Compact Vision System controllers, industrial computers and workstations. During the control process, the wheel is watered with a magnetic-luminescent emulsion, magnetized and exposed to ultraviolet radiation. As a result, the emulsion deposited on the defects glows in the visible range (yellow-green light). Eleven FireWire (IEEE 1394) color cameras with a resolution of 1280 x 1024 are used to scan the wheel surface. In one iteration, they completely cover a 20-degree sector of the wheel.
-
Product
Ion Beam System
-
Veeco's unmatched Ion Beam know-how delivers proven etch and deposition performance enabling the data storage and MEMS markets for decades.
-
Product
Diamond-like Carbon (DLC) Foils
-
An intense laser beam is used to evaporate carbon from a graphitic sputter target. In the process, the graphite structure of the source material is converted into nano-particles, which deposit on prepared substrates as diamond-like carbon. The properties of these unique carbon foils make them useful in a variety of applications, in particular beam stripping, as backings for accelerator targets or x-ray attenuators.
-
Product
Ozone Gas Generators
-
SEMOZON® Ozone gas generators and subsystems are the industry standard for compact, high concentration, ultra-clean ozone gas generation. Applications include Atomic Layer Deposition (ALD), Atomic Layer Etch (ALE), Chemical Vapor Deposition (CVD) and Wet Cleaning.
-
Product
RF Plasma Power Systems
-
These are ideal solutions for plasma apps like etching, cleaning, deposition and more
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
Panel Light-I-V Teste
ASIV-11
-
Greensolar Equipment Manufacturing Ltd.
The Panel Light-I-V Tester (ASIV) is used to test photovoltaic panels or modules during their production. A flashlight illuminates the work piece with similar light spectrum to that of the Sun, while the electric performance of the unfinished panel or the finished module is accurately measured. With the help of the tester the user can filter out reject panels. Testing the final performance reveals changes made by alternations in the deposition recipe.
-
Product
Pulsed-DC Systems
-
Extend process innovation with Advanced Energy’s comprehensive pulsed-DC suite. Minimize arcing, enhance deposition rate, improve film flatness and packing density.
-
Product
Dimensional Metrology
Stand-Alone Metrology Family
-
Nova’s stand-alone metrology platforms are utilized to characterize critical dimensions such as width, shape and profile with high precision and accuracy and are used in multiple areas of the fab such as photolithography, etch, CMP and deposition in the most advanced technology nodes, across all semiconductor leading customers.
-
Product
Duct Deposit Measuring System
-
The Elcometer 456 Duct Deposit Measuring System has been specifically designed to meet the requirements of the DTT (Deposit Thickness Test) in HVCA’s (Heating & Ventilation Contractor’s Association) Guide to Good Practice, for the measurement of dust and grease deposits within ventilation systems and kitchen ducts made of ferrous metals.
-
Product
ITO (Indium Tin Oxide) Electrode
-
This quite unique material transmits only visible light whereas it does not transmit UV radiation. Our ITO electrodes consist of 100 nm thick of ITO layer deposited on quartz or borosilicate glass substrate (0.5 mm thick).
-
Product
ALD Applications
-
Atomic Layer Deposition (ALD) has the potential to optimize product design across a wide array of applications from making silicon chips run faster, to increasing the efficiency of solar panels, to improving the safety of medical implants.
-
Product
Physical Vapor Deposition Systems
-
Physical Vapor Deposition (PVD) systems use physical processes, like sputtering and evaporation, to deposit thin films with exceptional purity and control. These techniques are widely used in semiconductor manufacturing, optical coatings and protective applications.
-
Product
High-grade type Gas Monitor for Chamber Cleaning End Point Monitoring
IR-400
-
The IR-400 offers real-time monitoring of the chamber cleaning end point during the deposition process. By optimizing the cleaning process, the IR-400 reduces cleaning time and gas usage. This reduction in cleaning gas usage leads to a reduction in chamber damage and increases the life times of all the systems components.
-
Product
In-Situ Spectroscopic Ellipsometer for Real-Time Thin Film Monitoring
UVISEL Plus In-Situ
-
The UVISEL Plus in-situ spectroscopic ellipsometer can be easily mounted on process chambers (PECVD, MOCVD, sputter, evaporation, ALD, MBE) for the real-time control of thin film deposition or etch processes.The UVISEL Plus in-situ provides the unique combinations of very high speed, sensitivity, dynamic range and accuracy making the instrument able to control deposition / etch at the atomic layer thickness level, even for rapid processes.
-
Product
NR01 net radiometer
-
Hukseflux Thermal Sensors B.V.
NR01 is a market leading 4-component net radiation sensor, mostly used in scientific-grade energy balance and surface flux studies. It offers 4 separate measurements of solar and longwave radiation, facing both up and down. NR01 owes its popularity to its excellent price / performance ratio and major improvements relative to comparable instruments. These advantages include weight, ease of levelling, solar offsets in the longwave measurement and pyrgeometer heating, reducing measurement errors caused by dew deposition.
-
Product
X-Ray Detector
XRT Detector Onyx
-
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
Product
PED Systems
Pulsed Electron Deposition
-
Is a process in which a pulsed (80-100 ns) high power electron beam (~1000 A, 15 kV) penetrates approximately 1 μm into the target resulting in a rapid evaporation of target material. The non-equilibrium heating of the target facilitates stoichiometric ablation of the target material. Under optimum conditions, the target stoichiometry is preserved in the deposited films. All solid state materials – metals, semiconductors and insulators, including those transparent to laser wavelengths in PLD – can be deposited as thin films with PED. By combining PLD and PED, the range of complex materials that can be prepared as thin films can be greatly enhanced.
-
Product
PICO Pµlse Contact Dispense Valves
-
This contact dispense valve provides many of the same benefits of the PICO Pµlse jet valve, including high-speed dispensing at up to 1000Hz continuous*. It also delivers more accurate contact dispensing with less turbulence for greater fluid deposit consistency, placement, and process control.
-
Product
Micro-spot DUV Reflection and Transmission Spectrophotometry
FilmTek 3000 PAR
-
Scientific Computing International
Metrology system with a 50µm spot that delivers high-performance transmission and reflection measurement of patterned films deposited on transparent substrates. Ideally suited for measuring the thickness and optical constants of very thin absorbing films.
-
Product
Optical Fiber Type Hot Phosphoric Acid Concentration Monitor
CS-620F
-
In 3D NAND manufacturing process, dozens of layers of SiO2 and SiN are deposited, and the SiN layer is selectively removed using hot phos.In this process, the desired etching rate can be achieved by controlling the concentration and temperature of the chemical solution.Previous products have difficulty to measure high temperature chemicals, but the CS-620F is able to measure at high temperatures up to 170 C degrees.
-
Product
Pure Boron Foils
-
MICROMATTER™ boron foils are also produced by laser plasma ablation; however, the deposition process is much more complex and time consuming than that for diamond-like carbon. Accordingly, only thin films, mainly designed for beam stripping of heavy ions in electrostatic accelerators, are available. All films are generally delivered on glass substrates coated with a release agent.
-
Product
Sputtering Systems
-
Known for precision and cleanliness, Veeco Ion Beam Sputtering (IBS) systems are ideal when engineers need tight control over film thickness, composition, and optical performance. Using a focused ion beam, IBS dislodges atoms from a target, depositing them onto a surface in smooth, ultra-uniform layers.
-
Product
Vapor Concentration Monitor
IR-300 Series
-
Metal-Organic Chemical Vapor Deposition (MOCVD) is widely used in the manufacture of LEDs, optical devices and other components. Liquid and solid precursors are delivered to the reaction chamber by controlling the temperature, pressure and the carrier gas flow rate (bubbling method). Process results can be affected by changes especially in temperature and liquid level. The in-line IR-300 Series measures and reports the precursor concentration in real time.
-
Product
Multi-Element Standards
-
These multi-element standards consist of multi-layer thin film coatings, one on top of the other, upto a maximum of 6 elemental coatings. It is generally recommended to have coating thicknesses < 20 µg/cm2, so as to cause negligible notable matrix effects, in particular absorption of X-rays emitted in lower deposits by those covering them.
-
Product
Long Term Test Kit
-
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to the intake of electrons at the electrode, the chromium ion will transform to chromium oxide and be deposited at the cathode triple point. In such a case, the long term test kit is used. The Inconel 601 flange is equipped with an alumina housing (>96 % Al2O3) and the air (or other gas) is led through an alumina tube. The long term test kit is fully compatible with other functionalities proposed with the Open Flanges™ test Set-Up as the integrated steamer or the small pellet test kit. The long term test kit can be implemented on the fuel, on the air or on both sides.
-
Product
Spectrometer
AirSPEC
-
Baltic Scientific Instruments, Ltd
Scintillation gamma-ray spectrometer AirSPEC is intended for measuring scintillation spectra and alsofor determination of activities and specific activities of radionuclides in samples and in conditions of natural occurrence in geometries 2 and 4.Spectrometercan be usedfor various tasksradiation monitoring, including the definition ofspecific effective activity of naturally occurring radionuclides (NORM) in building materials (granite,crushed stone, gravel, etc.), raw materials, products, waste industrial productionand rockswithoutsampling; measurements surface activity of the radionuclide 137Cs (and other); mass fraction of NORM in rocks andoresin the conditions oftheirnatural occurrence on a surface, inboreholes and in warehouses andtransportcontainers, and also in study ofsurface contaminationof soil,as well asprospecting and exploration ofmineral deposits resources.The spectrometercan be used forworkin the laboratoryand in the field conditions.
