Trace
-
Product
Incident-based Abnormal Software Behavior Analysis Services
-
If you have a software problem that no one can analyze, need training to get your developers, support and escalation engineers improve their troubleshooting, debugging, memory dump and software trace analysis skills or just need the expert opinion on an existing analysis report please don't hesitate to contact us.
-
Product
Cable Tracers
181 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
Carbon / Water Analyzer
CW‑800
-
Determination of released carbon dioxide and water is a special requirement for quality control in the cement and lime industry. ELTRA’s CW-800 analyzer is designed for the precise, simultaneous determination of carbon dioxide and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil and minerals. The CW-800 is equipped with a resistance furnace with quartz tube for sample oxidation and can provide temperatures up to 1000 °C. The temperature of the CW-800 can be set up in steps of 1 °C and the temperature is fixed during measurement. As common carrier gas in the CW-800 nitrogen is used.
-
Product
CX4000 – FTIR Gas Analyzer
-
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
Product
Visual Fault Locators
-
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
Product
Fixed-Mount Barcode Readers
DataMan 280 Series
-
DataMan 280 series fixed-mount barcode readers offer fast decoding, easy setup, and valuable Industry 4.0 features, like web browser connectivity and performance monitoring, in a small form factor. DataMan 280 was engineered to better track and trace items throughout manufacturing and logistics supply chains solving a broad range of tough 1D, 2D, and direct part mark (DPM) code applications.
-
Product
IRIDIUM TRACKERS
-
Robustness, Reliability, Long Lasting and a Low Cost price were the keywords during the design of this versatile device. The GTTS-3000 transceiver was developed to track &trace sea going Vessels and offer a true Global coverage. There is a wide range of options available to accommodate a lot of maritime applications.
-
Product
Trace VOC Analyzer
PTR-TOF
-
Extremely sensitive real-time PTR-TOF VOC and organic particle analyzers. The world's bestselling PTR-TOFMS series with TRU-E/N and patented ion-chemistry quality. Find the perfect match for your analytical challenge!
-
Product
JTAG Boundary-Scan I/O Modules
SCANIO Family
-
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
-
Product
Trace-level, Photolytic, True NO2/NO/NOx Analyzer
Model T200UP
-
Teledyne Advanced Pollution Instrumentation
The Model T200UP provides trace level measurements of NO and NO2 using our Model T200U NOx analyzer combined with a patented high efficiency photolytic converter. Even low temperature molybdenum converters transform other nitrogen-containing compounds such as HNO3, PAN, etc. to a considerable extent. Simultaneous measurements of NO2 performed with molybdenum and photolytic converters have shown significantly different results in the presence of such compounds.
-
Product
Voltammetery/CVS
Portable VA Analyzer
-
Portable voltammetric analyzer for the determination of trace levels of arsenic, mercury, and copper in water
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Heavy Copper PCB
-
Your product descrVictory is a professional Advanced Circuit Manufacturer, We provide 3OZ ~ 6OZ Heavy Copper PCB.Heavy Copper PCB are generally used for high power distribution, heat dissipation, planar transformers, and power convertors. We can make up to 6oz Heavy Copper PCB.iption goes here.Monthy Capability: 3500 Sq M/MonthLayer: 4 LayersMaterial: FR4 TG170Dimension: 350.56mm*580mmFinished board thickness: 2.3mmOuter layer Finished copper thickness: 6ozInner layer base copper thickness: 6ozMin Trace Width/Space: 14milMin hole size: 0.2mmMin hole wall copper: ≥25UMSoldermask Color: Gloss BlackSilkscreen Color: WhiteSurface finishing: HALApplication field: Communication Field
-
Product
Downhole Minimus
-
For deployments exceeding 100 metres in depth, we recommend the Downhole Minimus digitiser. Digitizing the data at source ensures that the origin can be definitively traced and not subject to attenuation during the travel to the surface; so signals are stronger and more reliable.
-
Product
Multifunctional Cable Detectors
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Multifunctional Cable Detector has a very high cost-effective, it can quickly trace and identify UTP/STP RJ45/ RJ11/BNC/ metal cable.
-
Product
Circuit Tracer
6503
-
Peaceful Thriving Enterprise Co Ltd
It is designed to identify and trace wires or cables without damaging the insulation; you just simply attach the sender unit to the circuit and follow the wires using the detector. This device is formed by 1x Sender and 1x Detector.
-
Product
Mixed Signal Oscilloscope: 33 GHz, 4 Analog Plus 16 Digital Channels
MSOV334A
Oscilloscope
33 GHz analog bandwidth4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Semi-Rigid Test Probes Up to 6 GHz
-
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Product
DC Parametric Test System with Curve Trace
DC3
-
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
Product
PCI Adapter for cPCI
PCI2cPCI
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
Hybrid Worst-Case Timing Analysis
TimeWeaver
-
AbsInt Angewandte Informatik GmbH
TimeWeaver combines static path analysis with timing measurements to provide worst-case execution time estimates.The tool estimates the worst-case execution time (WCET) of tasks based on the execution time of trace segments obtained from real-time instruction-level tracing. The computed time bounds are valuable for soft real-time systems and provide feedback for optimizing worst-case performance.
-
Product
Visual Fault Locator
HW-205
-
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
Product
RF Components
-
Using a Vector Network Analyzer (VNA) for RF component testing for design and manufacturing is based on how the component performs. The analyzer is used in multiple ways from design to manufacturing to tuning, field monitoring and maintenance of antennas, filters, mixers, amplifiers, circulators, isolators, and other RF components. Key considerations component designers should pay attention to when finding an analyzer that fits their needs is a great dynamic range, low trace noise, and fast measurement speed.
-
Product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
-
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
Product
USB 2.0 Protocol Analyzer
Mercury T2
Protocol Analyzer
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
Product
Advanced High-Performance Logging & Tracing for .NET, Java & Delph
SmartInspect
-
SmartInspect is an advanced .NET logging, Java logging and Delphi logging tool for debugging and monitoring software applications. Identify and fix software bugs faster. Monitor and analyze applications in real-time. Find solutions to user-reported issues. Debug production systems while they run.
-
Product
Sonde Locator
vLoc3-Cam
-
The vLoc3-Cam is the easiest to use sonde locator on the market today. The omni-directional antenna array allows for approaching the sonde from any position. The directional arrows will guide the user first to the front or rear locate point and then directly to the sondes position. The vLoc3-Cam includes multiple sonde frequencies making it compatible with the major push cameras and crawler cameras on the market. The Pushrod Trace mode shows a second display geared for tracing the path of the pushrod deployed in the pipe or tracing pipes with an optional portable transmitter.
-
Product
Emulation Adapters
-
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
Product
Infiniium V-Series Oscilloscope: 20 GHz, 4 Analog Channels
DSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
