Phase Sequence
order of ac vice versa voltage / current cycle peaks in a polyphase system..
-
Product
AC Clamp Power Meter
CM3286 Series
-
Measure power ranging from 5 W at a low current of 60 mA to 360 kW. In addition to current, voltage, and power, measure simple integral power consumption and phase sequence. Discover manipulation of electric meters by comparing meter and integral power consumption measurements. Discover theft by measuring leakage current.
-
Product
Sequence / Rotation Indicators
-
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
Product
Phase Sequence Testers
-
UEi Test & Measurement Instruments
Is used for detecting the sequence of the supply in three-phase electric circuits.
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Multifunction Instrument
COMBI521EV
-
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Measuring and Monitoring Relays
-
Various measuring and monitoring relays are available for the purpose of monitoring electrical quantities. In addition to overvoltage, undervoltage, frequency, unbalance, phase sequence, phase failure and loop monitoring, special solutions for specific applications are also possible: extended temperature ranges, sector-specific standards, compact design, country-specific profiles.
-
Product
Phase Sequence Indicators (Contact Type)
ST-860
-
Standard Electric Works Co., Ltd
● Three functions in one unit: open phase, phase sequence and motor rotation indication. ● Large size alligator clips for easy clipping onto switch- boards terminals. ● Highly reliable. ● Identifies 3 phase sequence and open phase check.● Ideal for installing conveyor lines, pump systems and interconnected drivers.
-
Product
Clamp Meter, Auto, True RMS, 1 kA AC, 600 V AC, 50 mm Jaw Opening Max.
72-10445
-
The 72-10445 is a Clamp Power Meter Clamp with phase sequence. It measures active power (W), apparent power (VA), reactive power (VAr), power factor, phase angle and active energy (Wh) with built-in phase sequence test. Also measures AC current, AC voltage and frequency.
-
Product
Phase Sequence Indicators (Contact Type)
887 PR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032
-
Product
Installation Tester
M72
-
Multifunction installation tester for insulation measurement up to 500V, continuity of protective conductors, phase sequence with TRMS multimeter functions.
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Multifunction Meter for Electrical Installations
AMPI-530
-
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Three Phase Tester
4200
-
Peaceful Thriving Enterprise Co Ltd
*Fast and accurate measurement.*Portable and compact design, easy to carry.*Efficient, effective, reliable, easy and safe to use.*Two function in one unit. Including open phase and phase sequence.*This is idea for installing conveyor lines, pump systems and interconnected drivers.*Indicate phase orientation (clockwise or counter-clockwise) and whether each of three phases is live.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Multifunctional testers
MI 3152 EurotestXC
-
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
Product
Non-Contact Type Phase Sequence Indicator
895 PR
-
Standard Electric Works Co., Ltd
Protection class: IP40. Non-contact detector clips. No metal contact points to advocate greater safety. Two functions in one unit : open phase and phase sequence detection. Designed for checking a wider range of 3-phase power sources. LED display lights with buzzer indicator. Brightness button feature for better visibility in dimly lit areas or sunlight. Magnetic mounting feature.
-
Product
Multifunction Electrical Installations Meter
MPI-520
-
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
Product
Phase Sequence Indicators (Contact Type)
862 PR
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Checks a wide range of 3-phase power sources.● Ideal for installing conveyor lines, pump systems and interconnected drivers.● Waterproof design, protection class : IP24.● Special test leads length are available on request.
-
Product
Multifunctional testers
MI 3102 BT EurotestXE
-
MI 3102 BT EurotestXE is a multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. It supports AUTO SEQUENCE® testing of the TN, TT and IT earthing systems. ISFL measurements and the IMD tests can be performed. Besides, the MI 3102 BT EurotestXE enables on-line voltage monitoring, phase sequence testing, earth resistance measurement, illuminance measurement and TRMS current measurement. EurotestXE is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
Product
Motor Diag & Protection
Phase Sequence and Motor Rotation Meter
-
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
Product
Phase Rotation Testers
-
Our range of phase sequence indicators provide LED indicationof rotation. They are perfect for checking phase sequence in motors, pumps and air conditioning units.
-
Product
3-Phase Sequence Tester
61-520
-
*For use up to 600V*Color-coded insulators over alligator clips*Shock resistant housing*Easy to read*2-year warranty
-
Product
Two-Pole Voltage Tester
P-4
-
Sonel P-4 is reliable, particularly durable and safe 2-pole testers, which enable testing voltage, circuit continuity and phase sequence. It has been designed for use in extreme conditions both in industry and commercial applications. Advanced technology, a high level of safety and user-friendliness are the key features of the P-line voltage testers.
-
Product
Phase Noise Analyzer and VCO Tester
FSPN
Phase Noise Analyzer
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
Product
Phase Sequence Indicators (Contact Type)
855 PR
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
Product
Phase Angle Voltmeter, Industry Standard
2250A
Phase Angle Voltmeter
NAI's 2250A Phase Angle Voltmeter is the most accurate and versatile AC measurement tool in the Synchro/Resolver and LVDT/RVDT marketplace. Considered the industry standard and based on the latest DSP and FPGA technologies, the 2250A substantially extends and simplifies the capabilities of the legacy 2250 model.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Phase Angle Voltmeters
Phase Angle Voltmeter
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
Serial AC Power Sequencer
90-200-001
AC Power Sequencer
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
