Bus Analyzers
analyze and debug systems based on standard bus formats.
See Also: Serial Analyzers, PCI Analyzers, Bus
-
Product
Bus Analyzer
FireSpy® 3430b(T)/3830(bT)
-
The FireSpy3430bT and FireSpy3830bT as well as FireSpy3430b and FireSpy3830 bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3430b(T)/3830(bT) is the most advanced 1394 test equipment in the market.
-
Product
PCI Express Bus Analyzer / Exerciser / Endpoint
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PMC to PCI Adapters
-
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
Product
VME Bus Analyzer / Exerciser
VME650
-
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
Product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
-
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
PCI to PCI Express Adapter
SKU-011-01
-
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PMC Bus Analyzer / Exerciser
PMC650
-
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Bus Analyzer
FireSpy® 4430b(T)/4830b(T)
-
The FireSpy4430bT and FireSpy4830bT as well as FireSpy4430b and FireSpy4830 bus analyzers are DapTechnology's latest 4-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy4430b(T)/4830(bT) is the most advanced 1394 test equipment in the market. The FireSpy4430b(T)/4830(bT) in fact combine four FireSpy analyzers in one single instrument. They comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Bus Analyzer / Exerciser
PCF850
-
The PCF850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Bus Analyzer
FireSpy430b(T)/830b(T)
-
The FireSpy430b(T) and FireSpy830(bT) bus analyzers are the single bus models in the 4th generation of IEEE-1394 analyzers from DapTechnology. Based on the industry leading FireSpy810 the all new and enhanced architecture of the FireSpy430b(T)/830b(T) have again defined a new reference in IEEE-1394 test equipment! They comprise a significantly more powerful on-board processor, more memory and improved connectivity to the host.
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
-
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI BUS Interface Card
PCI301
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
-
Product
Bus Analyzer
FireSpy® 9433bTRGD/9833bTRGD
-
The FireSpy9433bTRGD and FireSpy9833bTRGD bus analyzer are world’s only 9-bus IEEE-1394 protocol analyzer meeting harsh flight line and in-field testing. Based on the 4th generation FireSpy analyzer architecture the FireSpy9432bT/9832bT but has been incorproated into an enclosure designed to meet MIL-STD-810 requirements.
-
Product
Bus Analyzer, Monitor, Debugger and Programmer
BusPro-I
-
In the world of rapidly accelerating product development cycles, engineers developing products which utilize the I²C and SMBus interfaces need a bus analyzer that is easy to use—fast and simple.Unforeseen problems such as functional bugs can cause schedules to slip so it is important to have the right tool to resolve them quickly by isolating the root cause.The Corelis BusPro-I analyzer is designed with that idea in mind—the right tool at the right price. Open the box and plug it in; everything just works.
-
Product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Bus Analyzer
FireSpy® 3432bT/3832bT
-
The FireSpy3832bT and FireSpy3432bT bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3432bT/3832bT is the most advanced 1394 test equipments in the market. The FireSpy3x32bT in fact combines three FireSpy analyzers in one single instrument. It comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Sideband Bus Protocol Analyzer
FS2700 DDR5
-
The FS27xx DDR5 Sideband Bus Protocol Analyzer is the latest DDR5 tool from FuturePlus Systems. FuturePlus has taken the complexity of 8 different JEDEC specifications and ported them into this very useful tool. DDR5 Validation Engineers and system integrators will not have to comb through complex specifications defining thousands of bits and register addresses. The tool takes care of this. Please request our data sheet for more information.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Bus Analyzer
FireSpy® 6432bT/6832bT
-
The FireSpy6432bT and FireSpy6832bT bus analyzer are the world’s only 6-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy6432bT/6832bTare the most advanced 1394 test equipment in the market. The FireSpy6432bT/6832bT in fact combine six FireSpy analyzers in one single instrument. They comprise a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
