Balancers
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
Precision Impedance Analyzer
TH2851-080
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-80MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration
-
Product
Balance Thermocouple Power Sensor, DC To 50 GHz
N8487S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
Triple Balanced Mixers From 0.05 To 4200 MHz
-
A triple balanced mixer uses two well matched quad-diode rings. Because of this, they offer wider LO/RF bandwidths than DBM designs. But more importantly, the TBM offers a higher dynamic range and lower distortion.
-
Product
CDNs
T Series
-
The T series CDNs are for cables with unshielded balanced conductor pairs typically found in ISDN, DSL and Ethernet data transfer applications.
-
Product
Deadweight Testers & Gauges
-
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area.
-
Product
- RS-485 DIN Rail Mounted Surge Suppressor
Model 8021NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Triple Stage Protection; Two Wire. The Model 8021NX is a DIN Rail mounted surge suppressor for 2-wire RS-485 circuits used to protect factory data networks, or, any RS-485 network that wants to avail itself of the DIN Rail packaging concept. The Model 8021NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
Test Cells
Immunity
-
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They exceed the requirements of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing. The Cells are a modified form of GTEM cell, using a balanced dual septum design which maximises EUT volume for a given external size of cell, and dramatically improves field linearity. The EUT volume is fully lined in structural polycarbonate capable of supporting heavy products and access is via a large, full height door at the end of the cell. Adjacent to the door is the I/O filter compartment which can be customised to suit the users requirements. USB, RS232, Parallel, Ethernet, co-ax and other product specific filters can be added at time of ordering.
-
Product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD
-
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
Product
Triaxial Linear Accelerometers
-
Columbia Research Laboratories
The Triaxial Force Balance Linear Accelerometers range from general purpose, low cost sensors, capable of measuring DC and low frequency acceleration simultaneously in three axes, to Miniature Airborne, Highly Reliable Sensors that operate from +24 to +32VDC Aircraft power. Also offered are compact, premium performance, extremely rugged sensors, well suited for demanding missile and airborne applications.
-
Product
Workstation Software
LabSolutions Balance
-
When connected to an analytical balance, LabSolutions Balance can be used to perform all processes automatically, such as calculating weighing results, and then save the weighing results in a LabSolutions database. Consequently, it eliminates the need for hand-written records and eliminates transcription errors. The software not only records sample information and results, but also protects data from malicious alteration and unintended overwriting or deletion and saves all audit trail information in a LabSolutions database.
-
Product
Antenna Holders / Baluns
-
They are vital components in radio antenna systems. They enable the conversion of a balanced signal to an unbalanced one, ensuring optimal communication between the antenna and the radio.
-
Product
VME PowerPC Single Board Computer
DP-VME-0669
-
The DP-VME-0450 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with Error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces the DP-VME-0450 allows the user to perform intensive I/O while permitting rigorous computing.
-
Product
Production Spin Testing & Balancing Services
-
Test Devices provides production spin testing and balancing services of production parts for customers with a repetitive need and who demand schedule predictability along with a quick turn-around time. Whether proof testing critical rotating components before shipment, pre-spinning to achieve required rotational growth prior to finish machining or simplifying the supply chain by consolidating pre-spin with rough machining and/or NDT inspection, Test Devices offers a full range of spin testing solutions.
-
Product
100Gb/s Coherent Receiver
-
The integrated 100-Gb/s DP-QPSK receiver incorporates two 90° optical hybrids with four pairs of balanced photodetector (PD) and four linear TIAs into a single butterfly package. Unlike other technologies in which the polarization beam splitter (PBS) and/or the power splitter (BS) are not included, Optoplex’s receiver includes both of them with the optical hybrids, PDs and the TIAs to offer a fully integrated solution which will benefit users in terms of completely removing fiber routing and the skew management. The integrated receivers work at the symbol rate up to 32GBaud/s.
-
Product
Energy Meter
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
Product
PC Based Rotor Tester
GTS 1000
-
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
Product
DC Bias Current Power Supply
TH1775
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH1775 is a DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. High frequency LCR meter could be used, when the frequency response range is wide enough. MPU controlled auto current balance technology is adopted to realize AC+DC current overlap and constant current output from 0 to ±20A. Two TH1775 can be paralleled to supply a maximum current up to 40A.TH1775 permits high frequency measurement up to 1 MHz and can be directly controlled by TH2816A, TH2817A, TH2818 and TH2819. TH1773/TH1775 with its low additional error, wide frequency response range and sweep output function is widely used in DC biased inductance measurement. TH1775 also provides a perfect solution for magnetic material analysis.
-
Product
NanoVIP® CUBE™
-
NANOVIP® CUBE™ is a modern, powerful, S-Class portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (balanced and unbalanced) networks, low and medium voltage.The advanced features and analysis software supplied makes it a suitable tool to the most demanding professional needs.Your product description goes here.
-
Product
Pressure Measurement Film
Prescale
-
Prescale allows you to easily measure pressure balance, distribution, and size. Created using Fujifilm's advanced thin film coating technologies, the pressure inspection sensor on the entirety of the film allows you to confirm pressure distribution of the entire surface at a glance. The color appears red where pressure is applied, and the color density varies according to the amount of pressure. To cover a wide pressure range (0.006 to 300 MPa), we supply eight types and nine variations of Prescale.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
NanoVIP® TWO™
-
NANOVIP® TWO™ is a modern, powerful, portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (3 or 4 wires balanced) networks, low and medium voltage.
-
Product
Milliohm Meter
16502
-
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluation4 channels R scan with balance check function for fan motor (combined with A165017 option)0.001mΩ~1.9999MΩ wide measurement range with 4½ digits resolutionStandard RS-232 interfaceOptional GPIB & Handler interfaceBin-sorting functionComparator and pass/fail alarming beeper functionLarge LCD display (240 x 64 dot-matrix)Friendly user interface
-
Product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
-
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
Product
Transfer Switches
Q Series
-
The Pro/Tran Q Series features 1-inch interchangeable circuit breakers. A 30A double-pole circuit breaker and a 20A double-pole circuit breaker, to handle heavier loads on the generator side, are included on each model. The balance of the circuit breakers are single-pole 15A.
-
Product
RH850 Family (Automotive Only)
-
The RH850 is Renesas Electronics' latest automotive micro-controller family that offers high performance balanced with very low power consumption over a wide and scalable range of products. This family offers rich functional safety and embedded security features needed for new and advanced automotive applications.
-
Product
Precision Impedance Analyzer (20Hz to 10MHz)
ST2839
-
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Product
High Temperature Wettability Tester
6200Z
-
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
-
Product
Chromatic Confocal Modular Sensor
CL-MG
-
Sciences et Techniques Industrielles de la Lumière
STIL chromatic confocal modular sensor head series represents the perfect balance between technology and precision.Industrial, compact and robust sensor heads, CL-MG models are available in a dozen of models, each one adaptable to specific environments (e.g. vacuum, heat, water, dust...).
-
Product
PCI Express Graphic Card with NVIDIA® Quadro® P4000
Quadro-E PEG P4000
Graphics Card
The Quadro-E PEG P4000 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1792 CUDA cores, 8GB GDDR5 onboard memory and support for up to four 8K (7680×4320 @ 60 Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
