AC Clamp Meters
measures AC voltage and current without contacting condutors.
-
Product
DC/AC Clamp Meters
-
ACA/DCA measurement up to 999.9A.All of function from new microprocessor technology.Inrush current(100ms) mode, for measuring start current formotors, lighting, etc.
-
Product
AC Clamp Meters
-
Power measure of Active power (KW), Reactive power (KVAR),Apparent power (KVA), Power Factor (PF)PF (cosØ), for 3Ø4W, 3Ø3W, 1Ø2W, 1Ø3W.Triple display: KW+V+A easy to read.Recorded each wire parameters of V, A, KW, KVA, KVAR, PF, Hz,total 25 parameters.AC current up to 1000A, AC voltage up to 600V.INRUSH (100mS), HOLD and PEAK functions.MAX and MIN recorded functions.MAX. Cable size: Ø34mm.Auto power off (10 mins), Black-light.EN61010-1, 600V CAT IV, 1000V CAT III.Dimensions: 246mm (H) x 80mm (W) x 43mm(D).
-
Product
AC Clamp Meter
2950 CL
-
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
Product
Mini 200 Amp AC Clamp Meter
DL6505
-
A compact clamp meter for use where access to cables is a problem. This instrument fits neatly in the hand and with a clamp opening of 18 mm it is ideal for those instances where it is hard to reach cables.
-
Product
Wireless Connectivity AC Clamp Meter
MS-W364
-
This is a external wireless connectivity Digital Clamp Meter with 4000 Count, True RMS, auto and manual measurement.
-
Product
1000A AC Clamp Meter
CM55
-
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
Product
Bluetooth Integrated Clamp Meter
-
This is a Bluetooth with memory Integrated Wireless Connectivity AC Clamp Meter
-
Product
AC Clamp Meter
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Measures AC voltage and current without contacting condutors.
-
Product
AC Current Clamp Meter
3280-10F
-
AC Current Clamp Meter with Broad Operating Temperature Range, Attachable Flexible Sensor, and Drop-Proof Durability
-
Product
AC Clamp Meter
ST-3620
-
Standard Electric Works Co., Ltd
● 3½ digit liquid crystal display with maximum reading of 1999.● Over range indication : "1" is displayed on highest digit.● Low battery indication: "B" sign appears on the display.● Response time: approx. 1 second.● Data hold: for all ranges
-
Product
TRUE RMS AC Clamp Meter
2960 CL
-
Standard Electric Works Co., Ltd
● True RMS measurement.● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).● Re-power on by pushing any of the push buttons or by changing the rotary switch mode after auto power off.
-
Product
AC Clamp Meter
CM3289
-
Use in even more applications with an optional flexible sensor. Measure both wires in confined spaces and thick wires with a single instrument.
-
Product
Clamp Meters
-
Clamp meter is a rugged high end AC clamp meter. With a UL listed safety rating of CAT IV 600V / CAT III 1000V, this clamp meter is built to get the tough jobs done.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
AC Emulator
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 1200 VAC, 32 A, 45 KVA, 3‑Phase
SL1212A
AC Emulator
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
AC Emulator
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 45 KW / 66 KVA
SL1214A
AC Emulator
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
MSO Cable Kit, 16-Channel
N2756A
Cable Clamp Kit
The N2756A is a low-cost 16-channel MSO cable kit for InfiniiVision Series oscilloscopes. The kit includes 1 flying lead cable, 5 right-angle grounds, 5 ground extenders, and 18 grabbers.
-
Product
Serial AC Power Sequencer
90-200-001
AC Power Sequencer
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
Product
EPM-P Series Single Channel Power Meter
E4416A
Power Meter
The E4416A single channel EPM-P series power meter, for peak, average, peak-to-average ratio and time-gated measurements, using the E9320 peak and average power sensors.
-
Product
Capacitance Meter
E4981A
Capacitance Meter
The E4981A capacitance meter offers a high-speed with reliable measurements for ceramic capacitor testing in the production lines. The E4981A realizes the measurement capabilities of capacitance from small to large values with accurate measurements. The E4981A capacitance meter contributes improvements of the test throughput, while attaining excellent component quality for ceramic capacitor testing.
-
Product
EPM-P Series Dual-Channel Power Meter
E4417A
Power Meter
20 M sample/s per second sampling rate for reliable continuous and single shot measurements on wide bandwidth signals Time-gated and free run power measurements Free Analyzer Software software for complete pulse and statistical analysis, software is located In the Library8 pre-defined wireless configurations (GSM, EDGE, NADC, iDEN, Bluetooth, IS-95 CDMA, W-CDMA and cdma 2000)
-
Product
EPM Series Dual-Channel Power Meter
N1914A
Power Meter
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
Product
P-Series Modular Power Meter (LXI Compliant)
N8262A
Power Meter
The Keysight N8262A P-Series modular power meter enables LAN-based automated measurements of peak, peak-to-average ratio and average power. The N8262A enables fast, efficient, and cost-effective creation and reconfiguration of your ATE system. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
Product
Optical Multiport Power Meter
N7745C
Power Meter
Keysight's popular N7745A optical power meters with eight power-sensor channels provide increased throughput and operational efficiency to meet today's challenges in manufacturing. Designed for characterizing optical multiport components, these optical power meters offer industry-leading solutions for device connectivity, high-speed measurement data acquisition and fast data transfer for post-processing. The multiport power meter enables fast measurement solutions for all multiport devices; for example multiplexers, PON splitters, wavelength selective switches (WSS) and ROADMs, as well as compact setups for simultaneous testing of multiple single-port devices.
-
Product
EPM Series Dual-Channel Power Meter
N1914B
Power Meter
The N1914B EPM series dual-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
Product
Wavelength Tracker
10717A
Wavelength Meter
The Keysight 10717A Wavelength Tracker tracks changes in the air's index of refraction to optically compensate for environmental changes. It uses one axis of a laser measurement system to report wavelength of light changes, not changes in position. It is used to correct displacement values reported by other measurement axes in the system, hence improving measurement accuracy. It provides a higher degree of accuracy than environmental sensors such as the 10751C and 10751D Air Sensors.
-
Product
LCR Meter 10Hz - 100 kHz High Precision
T3LCR1100
LCR Meter
LCR Meter 10Hz - 100 kHz High Precision.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
LCR Meter
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
LCR Meter 10Hz - 300 kHz High Precision
T3LCR1300
LCR Meter
LCR Meter 10Hz - 300 kHz High Precision.
