Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
O/E Converter
TIA-3000
-
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
Product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
Digitizer
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
Product
Ethernet & NLINE: Real-Time 1553 & ARINC Converter/Bridges
-
Alta’s Ethernet (ENET & NLINE) Avionics converters are the first and most unique Ethernet appliances in the industry. A real-time UDP server engine (no IP software stack like most other products on the market) provides direct data buffer and transmission control of MIL-STD-1553 and ARINC-429 interfaces.
-
Product
Temperature and humidity duct probe
T3113
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Coating Thickness Meter for Ferrous and Non-Ferrous Substrates
CM8829
-
- Operating principle: magnetic induction/eddy current (F/NF)- Measuring range:0-1250um/0-50mil- Resolution; 0.1/1- Accuracy: 閸?-3%n or 閸?.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm- Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AAA(UM-4)battery- Auto power off- Operating conditions:0-+45闁?/span>(32闁?/span>-104闁?/span>),闁?0%RH- Dimensions: 126x65x27mm- weight: 81g(not including battery)- Optional accessories: other range 0-200um to 15000um
-
Product
IP Gateway
SFT3508F
-
Hangzhou Softel Optic Co., Ltd.
SOFTEL SFT3508F IPTV Gateway is a device which is used for the protocol conversion scenarios and streaming media distribution scenarios. It can convert the broadcast network IP stream over HTTP, UDP, RTP, RTSP and HLS and TS file into HTTP, UDP, HLS and RTMP protocol. The system can achieve the integration by receiving a variety of commercial streaming media services. Also, the system can provide streaming media services directly.
-
Product
Controller Card
GPIB-PCI-XL
Controller
The GPIB-PCI-XL is a flexible PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
Modbus Register Converter - Serial To Modbus RTU Interface
-
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
Product
Synchro/Resolver to Linear DC Converter
DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
Product
LCR Meters
-
GAOTek LCR meters are devices designed to measure the inductance (L), capacitance (C) and, resistance (R) of an electronic component. The LCR meters are measured in term of impedance but it can be converted through the instrument’s circuitry so the meter reads L, C and R directly with no human calculation required.
-
Product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
Analog Output Module
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
Product
Process NIR Analyzers
-
Process near-infrared (NIR) analyzers continuously measure moisture, oil, coat weight and other parameters directly in manufacturing processes for responsive process control. Common industries include wood products, tobacco, snack foods, converting, and bulk materials. A variety of sample interfaces, environmentally rated enclosures, and interface options are available for easy implementation and integration.
-
Product
Polarization Controller
-
Shenzhen Golight Technology Co.,Ltd
Polarization controller integrates an all-fiber dynamic polarization controller and a mini piezoelectric ceramic actuator. As a polarization controller, it can convert any input polarization state to the desired polarization state output. As a polarization scrambler, it can effectively disrupt the output polarization state.
-
Product
Unmanaged Ethernet Switches
-
CommFront offers a range of rugged, industrial-grade, managed and unmanaged Ethernet Switches. These Industrial Ethernet Switches have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of 10/100/1000M for both Fast and Gigabit Ethernet networks. In addition, our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet Switches support both point-to-point and multi-drop (daisy-chain or self-healing redundant ring) fiber optic networks, which are designed to cover large areas. These industrial Ethernet Switches support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. When configured as a ring network (managed Ethernet Switches), the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same ring, making the entire Ethernet network more robust and reliable.
-
Product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
64 Channel 100 KHz 16 Bit ADC Module
DP-VXI-1101
-
DP-VXI-1101, the 16-bit, intelligent, 100KHz A / D converter module can be widely used in data acquisition applications requiring high speed scanning with 16-bit resolution and high accuracy of 0.01% of reading.The module occupies one slot in the VXI 'C' size mainframe.DP-VXI-1101 module uses 8 channel signal conditioner plug on modules(SCP) for accommodating various input signals. Eight such SCP modules can be plugged onto the main board to accommodate a maximum of 64 channels per A / D converter module.
-
Product
DCDC
GA Series
-
The GA series is an economically priced 15 watt DC/DC converter featuring ultra-wide input range, efficiencies to 85% and a continuous six-sided shielded case. Low ESRcapacitors are used both on the input and the output(s) to minimize the conductive noise. Other key features include: overvoltage protection, output trim adjustability, TTL and CMOS compatible remote on/off, short circuit protection and small size. The GA series measures only 1.6” x 2.0” x 0.40” and offers a power density of 11.7 watts/cu. in.
-
Product
Net Radiometer
-
An on-board 24-bit A to D converter makes measurements and provides a digital SDI-12 output. This eliminates the need for multiple analog datalogger channels to measure each of the four components of net radiation.
-
Product
Universal Manipulator
LS
-
Manage the rapidly changing production environment and achieve the lowest cost of test, converting between probe, final, engineering and service positions with ease. Rapid advancements in semiconductor test technology have resulted in highly efficient test cells, capable of device test throughputs far greater than ever before.
-
Product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Interactive Event Platform
Virtual Event Space
-
Virtual Event Space is your tailored, interactive event platform that helps you engage audiences globally and convert viewers into customers.
-
Product
Temperature Data Logger
-
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
Product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
-
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
PXI-7841, Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780337-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7841 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
-
Product
Micro-Size Power Supplies
-
Advanced Energy’s micro-size, high voltage DC-to-DC converters offer a variety features — arc limits, tight line and load regulation, voltage monitoring, and more. Get the right solution in the perfect size.
-
Product
Inverters & Chargers
-
Sensata | Magnum-Dimensions provides a comprehensive range of inverters, inverter/chargers and converters that combines the smart technology you want with the rugged and durable design structure you need.
-
Product
CHNO Combustion Services
-
Carbon, Hydrogen, Nitrogen are determined using a 2400 Perkin-Elmer CHN Analyzer. This analyzer uses combustion to convert the sample elements to simple gasses, i.e. CO2, H2O, & N2. Upon entering the analyzer, the sample is combusted in pure oxygen environment at temperatures in the range of 1200-1500 F. The product gasses are separated under steady state conditions, and measured as a function of thermal conductivity.
-
Product
Fiber Optic Camera Adapters
SilverBack Series
-
We all appreciate the dramatic flair of cinematic video. Creating high-resolution broadcast content with cinematic quality has historically been a tall order, from cost of entry barriers to workflow integration. MultiDyne developed its SilverBack Series to help content producers convert digital cinema cameras into SMPTE studio cameras for live multi-camera production. SilverBack fiber camera adapters are lightweight “cameraback” systems ideal for live concerts, sports, TV productions and worship services. There are several models to meet varied budgets, all vendor-agnostic and engineered to adapt the user’s camera of choice. SilverBack systems offer modular designs to support diverse I/O configurations, with all signals carried over a single tactical or hybrid fiber cable. Hybrid and tactical fiber conversion as well as remote powering through MultiDyne JUICE portable power supplies further empower mobility for camera operators.
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
