CW
Wave having a constant amplitude and frequency.
-
Product
Power Meters
-
The Krytar Model 9000B is a low cost, high performance CW power meter using a diode based power sensor. The power meter can measure power levels from -39 to +20 dBm and cover frequencies from 100 kHz to 40 GHz. With bench and field service applications in mind, the power meter was designed to be completely portable. The power meter can be used for swept measurement.
-
Product
General Purpose Multimeter c/w Temperature
DL9102
-
Double moulded housing with an oversized high contrast 2000 count LCDdisplay. Manual ranging with current range up to 20A, temperature and frequency test.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Ultra-Narrow Linewidth, CW TI: Sapphire Laser with Integrated Green Pump Laser
SolsTiS PI
-
An evolution based on our heritage in industrial semiconductor applications, SolsTiS PI combines our award-winning SolsTiS titanium sapphire laser with our Equinox green pump laser into a single, integrated platform offering unprecedented levels of stability, compactness and ease of use while retaining all the benefits of the continuous-wave, ultra-narrow linewidth and broadly tunable architecture that SolsTiS is known for.
-
Product
Double Ridged Waveguide Horn
DRH20E
-
Frequency range: 1.6 GHz - 20 GHz VSWR (max): < 1.5:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 50W / 100 W
-
Product
Torque Gauges
-
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
Product
Double Ridged Waveguide Horn
QRH20E
-
Frequency range: 1.7 GHz - 20 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 20W / 40 W
-
Product
Visual Fault Locator
HW-205
-
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
Product
Wide Dynamic Range Power Sensor, E-Series
E4413A
Power Sensor
E4413A - The E4413A CW diode power sensor measures average power over the frequency range 50 MHz to 26.5 GHz and power range -70 to +20 dBm (90 dB dynamic range).
-
Product
Waveguide Power Meters
-
Start Frequency (MHz) 2400Stop Frequency (MHz) 2500Power (Watts CW) 5000Connectors TBR
-
Product
Visual Fault Locator
FFL-310-U
-
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
Product
Double Ridged Waveguide Horn
QRH40
-
Frequency range: 4 GHz - 40 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xK female Power (CW / Peak): 10W / 20 W
-
Product
Room Temperature Gyrotrons From 15 GHz To 35 GHz
-
Insight Product Company offers "Room Temperature" Gyrotrons and "Gyrotron Systems" within frequency range from 15 to 35 GHz and CW output power up to 10 kW.
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
Product
Camera Based Beam Propagation Analyzer: M2
BeamSquared
-
The BeamSquared® system is a compact and fully automated tool for measuring the propagation characteristics of CW and pulsed laser systems from the UV to NIR to Telecom wavelengths. Users can also measure wavelengths above 1.8 microns, including CO2 and terahertz in manual mode (a bench set-up; without the automated optical train) with a Pyrocam IV or IIIHR. Our longer optical train and patented Ultracal™ Calibration makes BeamSquared the most accurate product on the market and is ISO 11146 compliant. Its operational robustness and reliability ensures continuous use applications in industry, science, research and development.
-
Product
Double Ridged Waveguide Horn
H-A50
-
Frequency range: 33 GHz - 50 GHz VSWR (max): < 1.35 :1Impedance: 50 O (Ohm)Connector: 2.4 female Power (CW / Peak): 10 W / 20 W
-
Product
Coaxial Power Dividers
-
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
-
Product
Instrumentation HPAs
-
Communications & Power Industries
CPI SMP Division provides a complete line of high-powered continuous wave (CW) and pulsed instrumentation amplifiers for EMC testing, available in octave and multi-octave bandwidths from 1.0 GHz to 95.0 GHz and power levels exceeding 2.0 kW to meet the new military and automotive standards. CPI is the only supplier that manufactures both the traveling wave tube (TWT) and the TWT amplifier.
-
Product
Socket Tester c/w Buzzer
DL1090
-
Clear visual and audible indication of wiring status LED indication of a wide range of wiring conditions Designed to EN 61010 and IP30
-
Product
Gyrotrons
-
Communications & Power Industries
• Frequencies up to 600 GHz• Power levels up to 1.5 MW CW
-
Product
PSG Signal Generators
-
Generate trusted microwave signals: get metrology-grade frequency & level accuracy with excellent distortion & spurious characteristicsRely on the highest quality signals from pure CW tones with 1 W of power to complex, vector-modulated signals with 4 GHz bandwidthReduce the time you spend on signal creation with Signal Studio softwareTake advantage of increased performance, flexibility & speed when you replace a legacy source with the code-compatible PSG
-
Product
DCDC
SW/CW Series
-
The SW and CW Series are highly efficient, single output DC/DC converters. Proportional energy transfer techniques enable these encapsulated modular converters to maintain well regulated outputs despite large variations in input voltage. The 2:1 input range makes the SW and CW Series ideal for applications where the input dc power is derived from abattery, a motor generator or other types of poorly regulated power sources.
-
Product
Wavelength Meters - Scientific
-
Bristol Instruments'' wavelength meters are for scientists and engineers who need to know the exact wavelength of their lasers. These systems use proven interferometer-based technology to measure absolute wavelength to an accuracy as high as 0.0001 nm. To achieve the reliable accuracy that is expected from Bristol Instruments, all of its wavelength meters include a built-in wavelength standard for continuous calibration. Systems are available for CW and pulsed lasers that operate at wavelengths from 350 nm to 12 m.
-
Product
Power Sensors
-
Measure CW power from 10 MHz to 50 GHz. Modulated Average Power Measurement. Peak Power Measurement.
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
Carbon / Water Analyzer
CW‑800M
-
ELTRA’s CW-800M analyzer is designed for fractional analysis of carbon and water in one single operation. It is based on the proven technology of the CW-800 but has a modified furnace which allows fast adjustment of the temperature in the furnace. Different fractions of carbon and water of the sample are analyzed by applying different furnace temperatures. ELTRA’s CW-800M analyzer is designed for the precise, simultaneous determination of carbon (released as CO2) and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil, minerals, slags and waste.
-
Product
WeighVault™
CW-90/90X
-
This specialized PC software for use with Rice Lake’s CW-90 and CW-90X checkweighers makes data entry easier than ever while expanding data storage and reporting abilities.As weighing occurs, WeighVault stores the details of each transaction for either a single scale or multiple scales. A variety of transaction and productivity reports can then be exported into word processing, spreadsheet or PDF formats for better control over weight data and overall business performance.Predicting growth? There’s no better reason to explore WeighVault software. WeighVault users can boost their checkweigher’s 50 product ID storage limitation to nearly limitless potential, and manage as many scales as necessary. And with a direct connection to your PC you’ll be able to quickly program, edit and manage each checkweigher and each unique product ID right from your PC’s keyboard!
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
Fibolocator
-
Fibolocator is an innovative device for measuring and characterizing breaks and other backscattering-causing faults in optical fibers. Time-resolved correlation reflectometry is the principle on which the device is based. It analyzes the backscattered light like a pulse OTDR, but unlike such OTDRs, cw laser diodes are used. The requirements for the test signal and the complexity of the system are low, which leads to very low costs for OEM subsystems.
-
Product
Precision Low-Loss Multiplexers
-
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
