Flaw Detectors
See Also: Flaw Detection, Ultrasonic Flaw Detectors
-
Product
Infrared Thermal Imaging Gas Leak Detector (VOCs)
EXPEC-1880
-
EXPEC 1880 infrared thermal imaging gas leak detector (EXPEC 1880) is a non-contact leak detector for volatile organic compounds (VOCs). It adopts a high-end mediumwave cooled type-II superlattice infrared detector and has passed Ex ic nc op IIc T4 Gc explosion-proof certification, with high protection level (IP54).
-
Product
Gas Detectors
-
Great for HVAC professionals, Klein Tools’ Gas Detectors provide quick and accurate results. Whether you need to detect and measure concentration levels of CO and temperature, refrigerant gases, methane, propane, and other combustible gases, you can expect performance and durability from Klein.
-
Product
Counterfeit IC Detector
Sentry
-
The ABI SENTRY is a unique solution for the quick and easy detection of Counterfeit ICs and components. ABI Electronics has over 27 years of experience in the field of Test & Measurement equipment as well as Contract Electronics Manufacturing. Knowledge of both industries has allowed ABI to design this product around two main concepts:
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
-
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
Product
Tunnel Diode Zero Bias Detectors
-
A tunnel diode zero-bias detector is a device that converts microwave and millimeter-wave radio frequency (RF) signals into a DC voltage without requiring an external power source
-
Product
Electro-optic Test Bench for IR Detectors
BIRD 210
-
Testing detectors requires the implementation of ultra-low noise driving electronics and presenting high quality optical stimuli to the detector under test. This meets all these requirements and allows to test any type of detector by easily implementing the detector’s driving signals and providing exhaustive and accurate measurement results.
-
Product
Doorbell And Telephone Detector
ELK-930
-
he ELK-930 performs three functions. It can detect ring activation from one or two doorbell buttons and a single telephone line. It conveniently isolates the voltage and current and produces an open collector (pull to ground) output which can be used to trigger an automation controller, relay, timer, etc.
-
Product
Superior Handheld Partial Discharge Detector
PDStar
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is proud to present one of our latest innovations, the PDStar. It integrates On-Line Partial Discharge (OLPD) testing and Infrared testing for MV and HV equipment, which combines UHF, AE, Ultrasonic, HFCT, TEV, and Infrared testing technologies. It is applicable for online PD testing, as well as abnormal heating and defect detection on all types of substation equipment. PD amplitude, PRPD, PRPS, and infrared spectrums provide critical data for determining the operational condition of electric power equipment. It connects to the PMDTCloud via Wi-Fi/3G/4G to upload test data, download test tasks, and receive diagnostic results in real time. Another uniquely advanced feature of the PDStar is that it integrates with a 100 MSPS (Mega-Samples per Second) HFCT signal processor, which greatly improves the performance for power cable OLPD testing.
-
Product
Hot Bearing Detector
-
Ultra-Tech's On-Board Hot-Bearing Detection Unit is a self-contained, microprocessor based monitor specifically designed to provide an on-board Surveillance System for monitoring AC traction motor bearing and wheel bearing temperatures of railway trucks.
-
Product
Log Detector, SMA, Positive Video Out, 10 MHz to 3 GHz
PE8040
-
Pasternack log detector PE8040 is part of our extensive in-stock RF, microwave and millimeter wave components available for purchase. This log detector is manufactured with SMA female to SMA female connectors. Our SMA log detector has a minimum frequency of 10 MHz and a maximum frequency of 3 GHz.
-
Product
Voltage Detectors
-
Non-contact voltage detectors can quickly detect live AC voltage. These handy devices are great for electricians to safety and quickly check the status of electrical wires.
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Industrial Gas Detector
OLCT 60
-
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
Product
Event Detectors
EDH Series
-
Is designed to monitor electrical connectors undergoing reliability testing. This instrument detects nanosecond-range electrical resistance fluctuations characteristic of malfunctioning electrical contacts.
-
Product
Card type, Mini Wireless Camera Detector, with vibration
SH-005V / 10127
-
This "Card type Mini Wireless Camera Detector / Hidden Camera Detector" is special made for detecting all kinds of wireless spy camera, but insensitive to mobile phone signal that leads user a peaceful mind without panic.
-
Product
Refrigerant Leak Detector w/ Solid Electrolyte Sensor
RLD15B
-
UEi Test & Measurement Instruments
The RLD15B Refrigerant Detector is designed and certified to meet the new tougher standards and detect the latest refrigerants. Equipped with a heated sensor to increase accuracy and reduce false alarms, the RLD15B displays approximate leak sizes with the digital leak size indicator to help pinpoint leak sources. Finally, the mechanical pump draws gas over the sensor faster providing a quick response in a variety of contaminated or windy environments.
-
Product
Crank Angle Detector
PP/PA series
-
The Crank Angle Detection System is composed of a crank angle detector, a slit disk and a power box with built-in amplifier. By mounting the slit disk and crank angle detector to the crankshaft end of the engine, it enables to detect the rotation angle required for various engine performance tests such with high accuracy and high response.
-
Product
Phantom Metal Detector
-
Available in aluminum or stainless steel with a wide variety of aperture sizes, Phantom Metal Detectors are built rugged to withstand the harshest applications. For heightened stability and performance in wet product applications, the IP69K certified BSH Extra Rugged Casing is utilized. An epoxy chute provides a complete waterproof seal on IP69K rated units.
-
Product
Personal Voltage Detectors
-
*Provides another level of safety for line crews, storm restoration workers and first responders*Alerts user to the proximity of electric fields or energized electrical equipment with a loud alarm and bright lights*Frequency of alarm increases as the user gets closer to the electrical hazard*Detects voltage above line-to-line*Typical initial warning distance is about 7 ft from a conductor*Warning distance increases with higher voltages*Field replaceable 9V battery with low battery indicator
-
Product
High Voltage Detector
AC HotStick
-
High sensitivity voltage detector for emergency responders. The AC HotStick is a safety device designed for professional rescuers which provides warning of exposed high voltage AC from a safe distance.
-
Product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
-
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
Product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
-
Standard Electric Works Co., Ltd
● Protection class: IP65● Bright LED visual indication● Audible indication● Non-contact voltage detection: 220Vac ~ 132kVac● Wide angle voltage detection● Frequency range: 40 ~ 70Hz ● Easy-to-prove method● Self-test function● Power source: 9V rechargeable battery ● Non-contact detection by proximity● Flashlight function● Operating temperature: 0°C~50°C● Humidity: 80% RH Max● Lightweight, robust and compact● Comply with EN 61326-1
-
Product
Remote Spectral Detector
CSS-45
-
The CSS-45 detector incorporates a powerful microprocessor which performs not only data acquisition but also all necessary lighting calculations. Both USB 2.0 and RS 485 interfaces are standard enabling the flexible configuration of single and multi-detector based systems. An optional software development kit supports integration into third party application software. With its wide spectral range from 360 nm to 830 nm the CSS-45 is ideal, for example, as a high accuracy photometric and colorimetric detector (according to CIE S023).
-
Product
Electrochemical Detector
800D
-
The Model 800C series is designed for electrochemical detection. This instrument can be used for monitoring the current passing through a flow cell in liquid chromatography/electrochemistry and in-flow injection analysis, as well as other electroanalytical applications.
-
Product
TERAHERTZ ROOM TEMPERATURE DETECTORS FROM 37.5 GHZ To 996 THz
-
Insight Product Company offers Golay cells that detect electro-magnetic waves at terahertz frequency ranges from 0.0375 to 996 THz.
-
Product
Lightwave Detector
N4377A
Lightwave Component Analyzer
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
Product
SMART Sensor Gas Detector
IMR EX440
-
IMR Environmental Equipment, Inc.
The detector uses natural diffusion as the method to detect gas. It is constructed with high strength engineering plastics composites with an antiskid rubber housing. The detector is comfortable to hold, is water-proof, and dust-proof.
-
Product
Detectors
-
Each detector is properly housed, complete with any associated circuitry and can be mounted directly at the exit slit of any of our monochromators.
