-
Product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
-
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
Rugged Aircraft Interface Devices
AB2-AID
Interface
The AB2-AID is ready to go with high-performance avionics I/O combined with valuable built-in features such as a 9-port Ethernet switch, Ethernet to serial bridge, and 8GB flash memory. All in a compact, rugged package for easier integration and longer life.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Dynatrol® Level Switch for Light Bulk Solids
CL-10GJ
-
Dynatrol® CL-10GJ Level Sensor is designed for sensitive or problem applications of materials that have a tendency to bridge or pack. It handles difficult products such as flour, cocoa, sugar, pharmaceutical powders, powdered lime and additional bulk solid materials for high, intermediate or low-point level detection. The CL-10GJ is typically used with bulk solid materials in the density range of 10-15 lbs/ft3.
-
Product
Memory And Storage
-
Intel provides technically advanced products that support every level of computing—from data center workloads to enthusiast usage. Intel® Optane™ memory creates an accelerated bridge between memory and storage. Intel® Solid State Drives (Intel® SSDs) provide storage flexibility, stability, and efficiency.
-
Product
2 PRI + 8 Port FXS PSTN Simulator Adv
CH-8FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
49 lane, 13 port, PCI Express
PEX 9749
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Ultra-low Noise Phase Inverter - Buffer
WMA-IB-LN
-
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
Product
Prefabricated Torque & Thrust Sensor
-
Teledyne LeCroy Test Services patented Quick Sensor is a pre-fabricated Torque & Thrust Strain Bridge that is applied to a shaft much the same way as a strain gage. This time-saving device was developed for the Nuclear Power Industry to reduce the time and effort required to install strain gages in a radioactive environment. Since it's introduction in Nuclear Plants, the Quick Sensor has become popular in many other industries and applications where gaging time and cost is a concern.
-
Product
PXIe Full Hybrid Chassis, 21-Slot (Gen 2)
42-927-101
Chassis
This 21-slot PXIe Chassis provides one PXIe system slot and 20 hybrid-compatible slots for application flexibility. The chassis utilizes three PCI segments with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI-specific high-accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane.
-
Product
8-Ch, 24-Bit, 25.6kS/s, Quarter Bridge Input IDAQ Module
iDAQ-873
Data Acquisition Module
High resolution (24-bit)Quarter-bridge supportedSynchronization along with other iDAQ modulesMultiple trigger modes for flexible configured acquisition timingBuilt-in digital filter for higher SNR
-
Product
Measurement
Multichannel Strain Gauge Meter
-
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
Product
PMC Module Carrier
SK1-CHORD
-
SK1-CHORD is equipped with a PCI Express® to PCI® bridge for conversion of data from the CompactPCI® Serial backplane, to the on-board PCI® parallel bus.
-
Product
VME to USB 3.0/Ethernet/Optical Link Bridge
V4718
-
The V4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
Product
Rapid Prototyping and Manufacturing
-
We work closely with you in the early in the life cycle of your product development. Our extensive knowledge of the latest innovative prototyping tools enables us to design and produce initial designs quickly and to specification. Once the prototype has been tested and the design accepted, we are able to provide full small scale manufacturing options to bridge the gap to full outsourced manufacturing.
-
-
Product
Arc System
ACQUITY
-
The ACQUITY Arc System is a quaternary-based, modern LC system for scientists working with established methods who are looking for the versatility and robustness required to bridge the gap between HPLC and UHPLC while continuing to support validated assays.
-
Product
VME to USB 3.0/Ethernet/Optical Link Bridge
VX4718
-
The VX4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
Product
PXI Strain/Bridge Input Module
Strain/Bridge Input Module
PXI Strain/Bridge Input Modules feature up to eightchannels that support quarter-, half-, or full-bridge sensors at speeds up to 102.4kS/s. The modules provide increased accuracy, high data throughput, and a range of synchronization features. Optional features include remote sensing, internal bridge completion, and shunt calibration options per channel. PXI Strain/Bridge Input Modules are ideal for dynamic strain, load and pressure measurements, and test cell installations requiring accuracy and flexibility.
-
Product
65 lane, 17 port, PCI Express
PEX 9765
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
FlexVPX Backplane
-
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
Product
TMR Gear Speed Sensors
-
MultiDimension Technology Co.,Ltd.
Magnetic gear tooth sensors utilize a unique push-pull Wheatstone bridge design, including one or two Wheatstone full bridges, with four or eight unshielded high sensitivity TMR sensing elements. The Wheatstone bridge creates a differential voltage output with respect to the magnetic field gradient along the sensor’s sensitive direction.
-
Product
Free Serial-TCP (More Than Just A Device Server)
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and speed. The Serial-TCP program (more than just a Device Server) bridges your existing Serial COM port and TCP/IP without the need for changing existing protocol. It works seamlessly and transparently, just like passive RS232 / RS485 / RS422 converters, repeaters, and hubs, while the difference is that one requires installation of cables and converters with limited distance; and the other simply makes use of the existing computers and networks with an unlimited transmission distance
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
System
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
Product
Oil Resistivity Test System / Million Meg Ohm Meter (MM1)
OTD-45
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Model : OTD-45OTD-45 is single self contained unit containing oil test cell, high frequency induction heating with temperature controller/sensor; dielectric loss measuring bridge, AC test voltage source, SF6 filled standard capacitor; high resistance meter; DC voltage source and all digital circuits.
-
Product
Hydraulic Pulse Fatigue Testing System
PFT-500
-
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
-
Product
PCI CONET Controller
A2818
-
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
