Parallel Digital Interfaces
-
Product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
Interface
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
PXIe-5624, 2 GS/s, 12-Bit PXI IF Digitizer
783132-01
IF Digitizer
The PXIe‑5624 is optimized for superheterodyne receiver architectures. It features an onboard digital downconverter, which converts IF signals to I/Q data. As a result, you can use the PXIe‑5624 either as part of a PXI Vector Signal Analyzer or as a stand-alone IF digitizer.
-
Product
PXI FlexRay Digitizer
PXD7113
Digitizer
Digitize high resolution waveforms with the fully isolated PXD series Digitizers. Minimize interference and measure "in-circuit". Measurement errors are reduced by a high input impedance.
-
Product
USB 1553 and ARINC Appliance
USB-MA4
USB Interface
The industry’s first USB 3.0 SuperSpeed Multi-channel MIL-STD-1553 and/or ARINC-429 appliance!1-2 1553 Dual Redundant Channelsand/or 8 ARINC-429 Channels (4 RX/TX and 4 RX)Supports ARINC-717 (shared with 429 channels)
-
Product
ARINC PCI Interface Card
PCI-A429
Interface Card
Alta Data Technologies’ PCI-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-01
Interface Module
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Interface Module
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2233-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Digital/Pattern/PE Card
PEMU32
Interface Card
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785595-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
PXIe Remote Control Interface Module
43-921-003
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-02
Digitizer
he NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
sbRIO-9881, Non-Enclosed, 1-Port C Series CANopen Interface Module
785966-01
Interface Module
The sbRIO‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The sbRIO‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The sbRIO‑9881 is compatible with only CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Aircraft Interface Devices
AID
Interface
Versatile Ballard Aircraft Interface Devices (AIDs) from Astronics offer a secure, open-architecture approach that empowers you to take control of your software and your data today and prepares you to leverage and incorporate the next-generation technologies of tomorrow, including the Internet of Things (IoT) for the aircraft.
-
Product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
Digital Multimeter
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-03
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module - The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
Digital IO
PA32IX
Digital I/O
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
-
Product
PXI Digitizer 16-Bit, 20MSa/s
M9217A
Digitizer
The M9217A PXIe Digitizer is a single slot with 2 isolated input channels that supports up to ±256V and a sample rate of 20MSa/s and 16-bit resolution.
-
Product
Interface
RAR-cPCI
Interface
Available in a range of configurations to match your needs, the RAR-cPCI provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols in a CompactPCI form factor.
-
Product
Interface Board for Conduction Cooled PCI Mezzanine Card Systems
EXC-708ccPMC
Interface Card
The EXC-708ccPMC is an ARINC-708 /453 interface board for conduction cooled PCI Mezzanine Card systems. The board supports two or four ARINC-708 /453 channels. Each of the channels can be programmed either as transmit or receive. Each channel implements an 8K×16 FIFO and supports polling and / or interrupt driven operation.The EXC-708ccPMC comes complete with C-driver software library including the source code.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (64-out LVDS, 8 SE, KU035)
787284-01
Digital I/O
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
GPIB User Installable Interface Module
EL34GPBU
Interface Module
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
NI-5752, 50 MS/s, 12-Bit, 32-Channel Digitizer Adapter Module for FlexRIO
781357-01
Digitizer
The NI‑5752 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
PXIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4X.4421-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
PXI Waveform Digitizer
PXD731x/70xx
Waveform Digitizer
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
M4i.4471-x8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them.
-
Product
NI-9435, ±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module
779010-01
Digital Module
±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module - The NI‑9435 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel accepts signals from ±5 VDC to ±250 VDC and 10 VAC to 250 VAC; features transient overvoltage protection between the input channels and earth ground; and has an LED that indicates the status. The NI‑9435 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
Ethernet Interface
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV moduleUp to three connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
