Battery Test
See Also: Battery Testers, Battery Simulators, Battery
-
Product
Switch Mainframe
SW1001
-
Switch between voltmeter and battery tester while testing. 66 channels max. (2-wire) to 18 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
Mini Multi-Battery Tester
Mini-MBT
-
The ZTS Mini Multi-Battery Tester (Mini-MBT) provides a comprehensive means of testing the state of charge or state of power for more than 15 battery types. The mini-MBT’s microprocessor-based design makes battery testing simple - using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
Battery Drop Tester for Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery drop tester is used to test the drop impact performance of large, heavy-duty packaging products by simulating real surface, edge, and corner differences.
-
Product
110-250V AC Multi-Function Screwdriver Voltage Tester
5120A
-
Peaceful Thriving Enterprise Co Ltd
With CE, GS and UKCA Approval. Operates by two LR41, 1.5V batteries. Test for voltage, continuity. By contact method, check on 110-250V AC. By non-contact method, check on 110-500V AC. Detecting pulse of the high-tension ignition.
-
Product
Full-Featured Life Cycle Test System
LCV
-
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Battery Testing System
C8000
-
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
Product
Digital Multimeter
DMT 2004
-
Monacor International GmbH & Co.
*2000 digit resolution*Voltage measurement up to DC/˜ 250 V*Current measurement up to DC/˜ 10 A*Resistance measurement up to 2 MΩ*Battery test for 9V block and 1.5V cells*Acoustic continuity test*diode test*Data hold (measured value memory)*LC display with switchable background lighting*overload protection*Supplied with test leads
-
Product
Battery Capacity Analyzer
Model BCA6/12M
-
- Instant Measurement of energy stored in a storage battery- Tests 6V or 12V Lead Acid Batteries from 2Ah to 100Ah Capacity- Suitable for any SLA, GEL or Car Flooded Batteries- Displays DC Voltage and Balance available Ah capacity of the battery- Shows the Internal Resistance of the battery- Powered by the Battery under test- Micro-processor based digital control of entire testing process- Specially designed 4-terminal probing Battery Clamp of 100A capacity- Test simulates 20-Hr discharge test (C/20) with a few seconds- Bright, back-lit LED Display for test process display- On-screen User Guidance for testing on the built-in LCD Screen- Easy to use, portable and robust housing in a custom extrusion
-
Product
Battery Test Software
-
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
Product
Horizontal Battery Crush Nail Penetration Test Machine
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Horizontal Battery Crush Nail Penetration Test MachineApplication: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
Product
Battery Analyzers
-
JUNXY battery internal resistance & conductance tester is a portable and hand-held battery test and measurement instrument for daily battery maintenance. It offers users a fast and reliable principle to on-line check groups of battery bank’s battery state of health (SOH), battery performance by quickly and precisely testing each cell voltage, internal resistance, conductance, connecting strip resistance and so on.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
Battery PACK (500v-1000v)Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
PACK test equipment adopts sinexcel, firstly adopts three-level AC scheme, and the detection process supports multi-gear switching. The device integrates voltage, temperature, pressure and other auxiliary channels, and CAN also integrate various communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, etc. It supports a variety of practical and innovative functions such as data one-click automatic export, which meets all aspects of PACK battery electrical performance testing.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
Battery Analyser 12V Graphic
BA12G
-
The Battery Analyzer 12V Graphic (BA12G) is a 12V battery analyser with fully graphics display creating a clear and understandable step by step instructions solving language barrier and is marketable worldwide. Has 3 functions: Battery, Starter, & Alternator tests for 12V systems.
-
-
Product
High-Volt Storage Battery ClusterTest System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
1700VPACK test equipment adopts sinexcel advanced high frequency isolation solution, small size, high efficiency, low heat dissipation, flexible configuration, the detection process supports multi-gear switching; The equipment CAN be widely used in ESS system detection, ultra-high voltage EV PACK battery and other fields, and can also integrate a variety of communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, and support a variety of practical and innovative functions such as one-click automatic data export to meet all aspects of PACK battery electrical performance testing.
-
Product
Auto Charging System Analyzer
TE6-0604
-
Hangzhou Tonny Electric & Tools Co., Ltd.
* For battery test *l For alternator test
-
Product
Walk in Explosion-proof Chamber (Auxiliary Equipment)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Explosion-proof Chamber is mainly used to test the safety performance of lithium ion battery, battery pack. Prevent test operators and other test equipment from being burned and exploding. At the same time, the explosion-proof test chamber with the smoke exhaust system can discharge the smoke generated in the test to the outside.
-
Product
Electric Vehicle
-
Chroma Systems Solutions, Inc.
EV Automotive and Battery Test Advancements
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
130 AMP Battery Load Tester
MD4370
-
Compact, ergonomically designed tester determines a battery's charge and tests batteries, starting, and charging systems.Powerful 130 amp load capacity provides more accurate test results.Uniquely designed clamps assure a positive connection on any style battery.
-
Product
Battery Test and Analysis System
BTAS-16
-
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
Product
Battery Pack BMS Test Equipment
WA-BMS-3NE
-
Xiamen WinAck Battery Technology Co., Ltd.
The battery BMS test system can be applied to the integrated test of 1S~100S power lithium-ionbattery pack BMS with LMU and BMCU modules, such as the BMS performance andHILL test.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
Battery Formation and Testing System
BFS 2000
-
BENNING Elektrotechnik und Elektronik GmbH
For many decades now, BENNING has designed and manufactured charge/discharge converters for the battery industry. These converters are used in both the production and testing processes involved in battery manufacturing and for series-testing of batteries. BENNING's BFS battery production and testing system provides a solution which makes it easier to control and monitor production and test processes which saves both time and energy. When used in power stations and rail applications (mobile version), it can be used to test and maintain a wide range of battery types.
-
Product
All-In-One Battery Testing System
-
Integrating charge-discharge and temperature testing into one.
