Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-104962000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
Product
Regulated Power Supplies, Output 0 to 24 VDC, 400 AMPS, 9.6 KW, P/N 5944C2
-
- Regulated Power Supply, 9.6 KW P/N 5944C2- Input: 220 VAC, 3 PH, 50/60 Hz- Output: 0 to 24 VDC, 400 Amps max- Duty factor: 100%- Ripple voltage: <3% across full output range- Setting: 0 – 100% current and voltage- Control: Constant current and voltage control- Ambient temperature: up to 95 degrees F- cooling: Forced air-cooled- Dimension: 17.6″H x 19.9″W x 21.6″D- Weight: 175 lbs.- Degree of protection: NEMA 2
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White Teflon, Single Ended (1.5 Amps)
7-121926000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White Teflon, Single Ended (1.5 Amps).
-
Product
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps)
7-235916000-036
Power Patchcord
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps).
-
Product
48V / 250 Amp Load
BD15-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
PXI Solid State Multiplexer, 30 Amp, Single 6-Channel
40-667A-012
Multiplexer Module
The 40-667A-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110145
Signal Contact (ITA)
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap.Plated in 50µ" gold
-
Product
1000 Amp AC True RMS Digital Clamp Meter
DL6403
-
True RMS reading on AC current and AC voltages provide accurate measurement regardless of the wave form, which makes this the ideal instrument for commercial and industrial applications where no linear loads are present.
-
Product
PXI 2 Amp MUX, Quad 8-Channel 2-Pole
40-635-009
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps)
7-241914000-036
Power Patchcord
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps).
-
Product
PXI Solid State Multiplexer, 30 Amp, Dual 3-Channel
40-667A-011
Multiplexer Module
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Open Pluggable Specification (OPS) Digital Signage Player With Socket G2 Intel® Core™ I5/i3 And Intel® HM76 Chipset
OPS870-HM
-
OPS870-HM Open Pluggable Specification (OPS) compliant signage player is powered by 3rd Generation Intel® Core™ processors. The high performance OPS870-HM is based on Mobile Intel® HM76 Express chipset and features 3rd Generation Intel Core processors based on the leading edge 22nm process technology. Axiomtek's OPS870-HM is engineered to be installed into any OPS-compliant digital signage platform to enable faster and easier installation, and straightforward upgrading and maintenance. It significantly provides superb graphics performance, full HD content playback, and dual display presentations. Equipped with the OPS870-HM, users can apply a variety of DOOH (Digital Out Of Home) applications with ease!
-
Product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 1m, 250 Port
A500RMR-C-4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
High Amps, Contact, ITA, 500+ Amps, 350 MCM
610153102
Power Contact
High Amps, Contact, ITA, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610152101. (NOT compatible with other VPC contacts)Contact ONLY compatible with 410105174 ITA.
-
Product
Electrochlorination Power Supply, Output 0 to 10.5 VDC, 130 Amps, P/N 4085C
-
Shown below is an Electrochlorination power supply with a 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced with a PLC system. These units are custom units, built to order.
-
Product
30 Amp Fuse Buddy
305M
-
*Fuse Buddy Testers can test circuit current up to 30 Amps. *Two 30 Amp models, #305M used with Mini size fuses and #306B used with ATC size fuses. *Blowing fuses? Get the Fuse Buddy, a great new product. *Clever design allows for easy connection into fuse sockets. *30 Amp models have resolution of .1A, while 20 Amp models have .01A resolution. *Fuse Buddy ends are molded into the shape of the fuse itself. *During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. *The Fuse Buddy stays put and won't fall out of the socket, like test probes do. 305M & 306B Specifications *Tests circuit current from 0 to 30 Amps/48 Volts *Resolution .1A (100 milliamps), accuracy + 2%
-
Product
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
7-245436673-036
Power Patchcord
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 26 AWG Twisted Pair White/Black, Single Ended (1.5 Amps)
7-105426000-036
Signal Patchcord
Signal, ITA, TriPaddle (7 Amps) 26 AWG Twisted Pair White/Black (1.5 Amps)
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Signal Contact (Receiver)
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
Product
High Amps, Contact, Receiver, 500+ Amps, 350 MCM
610152101
Power Contact
High Amps, Contact, Receiver, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610153102. (NOT compatible with other VPC contacts)Contact ONLY compatible with 310105172 Receiver.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 0.5m, 500 Port
A500RMR-500RMR-1B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
Product
1000 Amp AC/DC Inductive Amp Clamp
6043
-
• A great tool for accurate measurement of current sources up to 1000 amps• Use with most digital multi-meters• 1mV/Amp output guarantees easy reading on your meter• Ideal for checking starter draw, alternator output or parasitic battery drain testing• Design allows accurate current readings without breaking the circuit• Low battery indication – auto power-off• Switch settings OFF/200A/1000A• Large jaw opening, 2.2″ and large jaw space, 2.2″ x 2.75″• Imported
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
50-635A-006
Multiplexer Module
The 50-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
48V / 200 Amp Load
BD12-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin SGMC Connector, With Interlock
42-158-003-HI
Relay
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 24 AWG White, Single Ended (5 Amps)
7-124924000-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 24 AWG White, Single Ended (5 Amps).
-
Product
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module
310105172
Receiver
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module.Contacts rated to 1500VDC for low duty test applications.Mating ITA 410105174. (NOT compatible with other VPC Solutions)
