Headers
-
Product
Ribbon Cable Headers
DINterm64
-
Ribbon cable headers are commonly used with VME compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The DINterm64 converts from 64 pin ribbon cable to a 64 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Product
SparkFun Qwiic Micro:bit Breakout (with Headers)
-
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
CB-50LP Low-Cost, Unshielded I/O Connector Block
777101-01
Terminal Block
50-Pin Male IDA to 50-Pin, Female Screw Terminal, Panel Mount Terminal Block - The CB-50LP provides 50 screw terminals for connection to I/O signals from 50-pin NI data acquisition devices. The CB-50LP includes one 50-pin header for direct connection to 50-pin cables and metal standoffs for use on a desktop or for mounting on a custom panel.
-
Product
Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle
FE-5121
-
* Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle * 16K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 16MHz/ 3V, 5V * X1 and X2 Mode Support * MS-Windows Debugger for C and Assembler * Keil mVision2 Debugger Compatible * PLCC-52 and SSOP-24 Emulation Headers * Serially Linked to PC at 115Kbaud
-
Product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
SIM Insert
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
Product
JTAG Emulators
XDS100v2 Series
-
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
Product
Board-to-FPC Connector for 5G Millimeter-Wave Antenna Modules
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-To-FPC Connector for 5G Millimeter-Wave Antenna Modules offer good SI/EMI/EMS characteristics for high-frequency applications and features our industry-leading Tough Contact construction that achieves high contact reliability and retention force. Tough against shock impact by misalignment, the fully-shielded structure in both socket and header significantly improves EMI characteristics necessary for RF applications such as 5G.
-
Product
Interface for Two Dual-Redundant 1760 Channels
EXC-1553PCMCIA/Px-1760
-
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers. Each channel of the EXC-1553PCMCIA/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.The EXC-1553PCMCIA/Px-1760 card is supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 1m
40-971B-200-1m-MF
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
TMD37003 cRGB Color and Proximity Sensor
SEN-36004
-
Fully integrated carrier board designed to get the most out of the TMD37003 cRGB (color with IR compensation) and Proximity Sensor from AMS. This means that the board includes a 1.8V-5V input range LDO and high-speed signal voltage translation on all IO pins. In addition, we've added a high output white LED that is tuned to the light temperature range of the TMD37003 IC. This makes sensing color of close-proximity objects possible, such as in robotic color sorting operations. As on many of our boards, we've included 4-40 sized mounting holes to make installation easy. The IC functions are interfaced via a 0.1" header, which includes power (Vdd and GND), I2C interface (again, fully translated) and a 3.3V input to power the proximity (IR) LED. The on-board LED is turned on with a logic 'HIGH' applied to the LED pin and is powered with Vdd.
-
Product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
-
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Debug probe for ARM Cortex processors
USB Multilink ACP
-
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Connectors, Header - Male
INT-10040
-
1x40 pin breakaway header. These headers have square pins and fit intostandard 0.1" breadboards. Scoring makes for convenient breaking into smaller headersfor all of your projects. Gold plated and RoHS compliant.
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
Signal Module, ITA, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 151 107 And 510 109 316)
510151121
ITA Module
This kit has everything you need to attach a VPC ITA Module to a custom designed PCB. This includes the right angle header (P/N 510 109 316) and the ITA Module (P/N 510 151 107).
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
Product
Compressed Air Monitor and Alarm
SENTRY
-
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, To PCB-Mounted 6x32-Pin Ribbon Cable Headers
510150155
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 6x32-Pin Ribbon Cable Headers
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 1m
40-971B-200-1m-MM
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
Connectors, Jumper - Black
INT-10901
-
Jumper for 0.1" (2.54mm) spaced headers. These are also known as a 'shunt'. These mate with the 0.1" square-pin headers and are the 'open' frame style. RoHS compliant.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-MF
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
VTAC Vertical Header Insert
-
The VTAC vertical header insert is designed to mount on custom PCBs. Can be configured as a backplane connector and daughterboard connectors. Also sold as a set under 610151108.
