Media Converters
-
Product
HCU/DC-DC Converter ATS
8900
DC Converter
Low power testSleep mode current testInput overvoltage limit testLine regulation testEfficiency testLoad regulation testOutput ripple voltage testDC-DC load testOvercurrent testPower doen and isolation test
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Synchro/Resolver to Linear DC Converter
DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
DC Converter
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
16 channel 16 bit Digital to Analog Module
CPCI-DA16-2
Digital / Analog Converter
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Optical-Electrical Converter - MATRIQ
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
600-Watt DC/DC Converter, 6U VME
64PS1
DC Converter
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
Product
75-Watt DC/DC Converter; Single Output
55KS1
DC Converter
NAI’s 55KS1 is a 75-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +100° C.
-
Product
50-Watt DC/DC Converter; Single Output
55JS1
DC Converter
NAI’s 55JS1 provides full-power, single output at a baseplate temperature of +100° C.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Digital / Synchro Converter
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
Product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
Product
PXI 8/16-Channel Isolated D/A Converter
M9185A
Digital / Analog Converter
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Product
Multi-Function PXI Card
GX3788
Digital / Analog Converter
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
Product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
Digital / Analog Converter
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
16 channel 16 bit Digital to Analog
CPCI-DA16-1
Digital / Analog Converter
The CPCI-DA16 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA16 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
125-Watt DC/DC Converter, 3U cPCI
55LQ3
DC Converter
NAI’s 55LQ3 is a 125 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
Product
50-Watt DC/DC Converter; Dual Output
55JD1
DC Converter
NAI’s 55JD1 is a 50-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power output, dual at a baseplate temperature of +100° C.
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
AC-DC Rectifier / Converters
DC Converter
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
Product
Ethernet Media Switch
-
Ethernet media switch is a layer 2 switch running on Ethernet or Fast Ethernet. It equips with one or two fiber ports and four copper UTP ports and hence acts as easy-to-use add-drop equipment for connecting network devices into optical fiber network. Ethernet media switch meets corresponding IEEE 802.3 standards.
-
Product
100-Watt DC/DC Converter
55LS1
DC Converter
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
Mobii Media Encoder
-
The Smart Encoder is designed for semi and permanent based on-site installation. Deployed into sport stadiums/arena’s, Broadcast production sites, Data Centers and Outside Broadcast vehicles, the Smart Encoder will ingest a variety of input video sources such as SDI, NDI, SRT, MPEG-TS. The encoder will ingest, synchronize, encode and upload Microblock streams to the nearest cloud regional edge cluster for global distribution via the Co-Ordinator, or output a variety of streaming formats to local network for on-site usage.
-
Product
Internet based Media Solutions
-
The internet has reduced the financial outlay required to reach the globe with media. Now anyone with a web cam can start streaming content. These solutions are good for a handful of simultaneous viewers and collapse to stuttering video as the number of simultaneous users increase. At Ideabytes, we believe that video quality at an affordable rate is what producers and distribution technology require. Ideabytes has answered the Challenge with Qezy solutions that enable a broadcaster to eliminate satellite uplinks and rely on the internet to reach its audience with no geographical limitations. More at www.QezyTv.com
-
Product
Media Meter Software Tool
-
Dolby Media Meter is an innovative software tool that accurately measures loudness the way your viewers experience it in programming for broadcast, packaged media, cinema trailers, video on demand (VOD), and games. Differences in audio levels between programs and channels, or between programs and commercials, are a major annoyance to TV viewers. Although easy to hear, these differences are much more difficult to measure. And without accurate measurement, you can't regulate these irritating shifts in sound level.
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
