Limiters
-
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Limiters
-
A limiter catches the loudest peaks of an audio source and applies brick wall compression that prevents it from exceeding the clipping point of 0 dBFS.
-
Product
Limiters
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a complete line of RF and microwave limiters, LNA/limiters and limiting amplifiers up to 18 GHz. These products use the latest thin-film hybrid manufacturing techniques to obtain the highest levels of performance, repeatability, reliability and cost-effectiveness. Using the latest technology available in the industry for silicon and GaAs FET MMICs, these products are ideal for multi-market and aerospace and defense applications.
-
Product
Current Limiting Resistors
-
Current Limiting Resistors are designed for limiting the flow of current to some predetermined value and are used mainly to to keep flowing current within certain intervals while controlling the circuit.
-
Product
Monics 200®
-
Kratos Defense & Security Solutions, Inc.
Monics® 200 was developed to deliver advanced monitoring capabilities cost effectively for High Throughput Satellite (HTS) spot beams, fly-away environments and instances where only limited monitoring is required, such as remote teleports with a small number of antennas. Monics 200 is a fully featured and cost-effective monitoring device that integrates with the Monics system.
-
Product
Hygrometers
-
A hygrometer is a device used to measure humidity. Many hygrometer products also measure temperature. A hygrometer that measures both humidity and temperature often is referred to as a thermo-hygrometer. PCE Instruments (PCE) offers a wide variety of hygrometer products used to measure the relative humidity of the air.Since humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of hygrometer devices designed for specific applications such as measuring the humidity in bales of pressed hay or in rolls of paper. A hygrometer also can be used to evaluate heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, a hygrometer capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT). A combination hygrometer / thermometer, or thermo-hygrometer, can be used to verify the integrity of the cold chain during the transport and warehousing of refrigerated food and pharmaceutical products. This versatile and popular style of hygrometer also is ideal for evaluating the performance of HVAC systems in industrial, commercial and residential properties. If the humidity indoors is too high, mold can occur. Certain types of mold cause respiratory problems and other negative health effects for people living or working in the surrounding environment. In addition, mold that has permeated into the walls or roof of a structure must be removed for safety reasons. Mold remediation and removal, also called mold damage restoration, can be a costly endeavor, which is why preventative monitoring of the humidity indoors is preferable whenever possible.
-
Product
Failure Analysis Services
-
BMP Testing and Calibration Services Inc.
Failure analysis plays a crucial role in product development that enables industries to prevent future product failures and improve them for the end-user. It’s a multi-faceted approach to finding how and why a product failed and involves an in-depth investigation of the circumstances surrounding the failure and discovery of relevant background information, including but not limited to the type of application, environmental factors, service life, and pertinent design information.
-
Product
Tabletop Mask Aligner
Model 200
-
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
Product
Digital Micron Gauge
DMG150
-
UEi Test & Measurement Instruments
The DMG150 is a Digital Vacuum Micron Gauge with accuracy and precision required by HVAC and refrigeration technicians. Featuring measurements in 5 units including Microns, Pa, mBar, mmHg and mTorr. And is backed by a 1-Year limited warranty.
-
Product
Manpack MW Antenna
TGR-50 class
-
The TGR-50 class of rapidly deployable AM antennas is designed for easy transport and erection by limited personnel. No tower climbing or sophisticated lifting equipment are required for installation by a crew of three or four persons. Weight and packaging, according to model, typically permits transport by bearers, light vehicle, small boat, or helicopter. Disassembly and relocation is similarly convenient.
-
Product
SENSOR FOR THICK & CURVED MATERIALS
S3
-
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
-
Product
PXI High Density MUX BRIC, 2-Chan, 160-Pole
40-570-012
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI 10 x 4 to 1 RF Multiplexer 500MHz 50 Ohm Multiway Connectors
40-755-010
Multiplexer Module
The 40-755-010 is a 50 Ohm high density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a Souriau multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
Product
PXI High Density MUX BRIC, 16-Chan, 10-Pole
40-570-411
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
Product
Shock Reactance
ICR260 330
-
Lifasa - International Capacitors, SA
Shock reactors are necessary to limit the transient currents that occur in the connection of the capacitors.
-
Product
Video Autoselector
1154A
-
Consumers who own a receiver and/or TV with limited inputs can use the 1154A to add multiple A/V sources. Its exclusive Adaptive Signal SensingTM technology uses multiple criteria to decide when to switch sources, and adapts to users’ activity patterns, customizing its switching behavior over time. The high bandwidth circuitry accepts HDTV component video (YPbPr), stereo analog audio, and digital audio in both optical and coaxial formats, and switches all audio and video signals simultaneously when a new source becomes active. Digital audio signals are converted automatically to the desired format. Up to four sources may be connected to one receiver/video display system through the 1154A. A manual select button is provided to override the 1154A’s automatic selection. Multi-color front panel LEDs indicate source availability.
-
Product
Gauge Type T Thermocouple Wire
W-TW-20
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Charge-Coupled Devices ("CCD") Cameras
-
Improve limits of detection and quantification. The camera generates large amounts of data, but handles it smoothly via the new super speed USB 3.0 interface.
-
Product
Stress screening test chambers for temperature and climate
TS and CS series
-
Our based on the modular concept of the standard range of temperature and climatic stress screening test chambers allow you through increased compressor and large fan performance very high temperature change of up to 30 K / min with conventional refrigeration, or to 70 K / min with liquid nitrogen. These devices allow you to very quickly determine the load limits of your test object in fast motion.
-
Product
Condition Monitoring
-
m+p Coda is a versatile monitoring system that captures and records signals coming from sensors such as accelerometers, thermocouples, strain gauges, and pressure transducers. Limit checking and alarm monitoring is provided for every active channel. The active channels are clearly displayed in a separate window, out-of-limit data can be seen at a glance. Alarm events are entered into a log file and can be reviewed at any time. You have the option to change the alarm limits online at any time without stopping the data acquisition.
-
Product
Analog Oscilloscope
PS-1000
-
* 100MHz BANDWIDTH. * 20MHz LIMIT. *1mV SENSITIVITY. *2.0nS RESOLUTION. *CE. TUV GS, UL, CUL, IEC1010
-
Product
Osram Direct Emission Green Laser Diodes (510 - 530nm)
-
The Optoelectronics Company Ltd
The PLT3 520D laser diode can deliver 140mW pulses at 520nm with 8% efficiency, driven at 300mA at 50% duty cycle – OSRAM's previous limit was 80mW with the PL 520B. This new diode has been developed to work in MEMS-based scanners.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
Power Limiter, 0.01 to 18 GHz
N9356B
Power Limiter
The N9356B power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
Liquid Level Gauges
-
Provides a continuous indication of the liquid level inside of a transformer's main tank, conservator tank or load tap changer compartment with integrated switches that allows limit and alarm functions.
-
Product
12:1 IR Thermometer w/ K-Type Thermocouple Input
INF195C
-
UEi Test & Measurement Instruments
The INF195C offers the unique circular laser targeting showing users the exact spot being measured. This 12:1 Infrared Thermometer also offers advanced features including a wider temperature range, K-Type input, selectable emissivity levels, Min/Max, average, differential, a user adjustable alarm and backed by a 1-Year limited warranty.
