Vector Signal
See Also: Vector Signal Transceivers
-
Product
Signal Generator
MX-RFSG1800
-
The Maxcom MX-RFSG1800 signal generator is a simple low-cost device used to inject RF signals up to 1800 MHz into RF plant for the purpose of verifying those high frequencies are able to properly pass-through cables, passive and active devices.
-
Product
RR Signal Source
-
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
Product
Signal Converters
-
The signal converters from HEIDENHAIN let you flexibly adapt the encoder signal interfaces to the requirements of your applications. For some applications, additional signals, such as from temperature sensors, are processed and forwarded to the subsequent electronics.
-
Product
Quadrature Signal Generator
TE5100-PCI
-
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
Product
Vector Network Analyzers
-
RF VNA to a Broadband VNA, from a Premium VNA with the highest performance and no compromises to a Value VNA that offers solid performance with suitable measurement speeds for an R&D environment. No matter what your application, Anritsu has your VNA needs covered. Choose with confidence from the pioneers in VNA measurements, introducing the Wiltron 310 Impedance Meter in 1965, and introducing the first broadband VNA, spanning 40 MHz to 65 GHz, in 1999. The first to cover a span from 40 kHz to 125 GHz from a single coaxial connector.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
Digital Signal Processor
CHAMP-XD2
-
Curtiss-Wright Defense Solutions
Facing increasing SWaP-C demands and harsh environments, boards now need to be smaller and more powerful than ever, while still working with tight budgets. Standard cooling methods offer a low-cost, reliable solution when paired with a proven ecosystem of hardware and software.
-
Product
Signal Generator
8003
-
5 digit BCD, 1 latch control line, 25 pin female, D type connector. May take several minutes to achieve for the largest frequency steps. Normal switching mode, SSB phase noise will be degraded in the fast mode.
-
Product
I/P Electro-Pneumatic Signal Converters
TEIP11 / TEIP11-PS
-
Electro-pneumatic signal converters are the link between the control rooms and pneumatic actuators. I/P converters are available with and without booster stage.
-
Product
USB Signal Conditioning Products
-
Signal conditioning can include amplification, filtering, converting, range matching, isolation and any other processes required to make sensor output suitable for processing after conditioning. It is primarily utilized for data acquisition, in which sensor signals must be normalized and filtered to levels suitable for analog-to-digital conversion so they can be read by computerized devices.
-
Product
Signal Conditioners
SC-7400
-
The SC-7400 handles a variety of temperature and process inputs and offers combinations of analog and relay contact outputs. All parameters - such as input and output range, set-points, deadband and burnout - are customer-selectable via software.
-
Product
Digital Signal Processor Card
CHAMP-AV9
-
Curtiss-Wright Defense Solutions
The CHAMP-AV9 combines the floating point performance of the Intel Core i7 processors, with the substantial bandwidth and system-enabling features of the 6U OpenVPX form-factor. Providing a pair of quad-core 4th generation Core-i7 (Haswell) processors, featuring the updated AVX 2.0 instruction units and redesigned on-chip graphics execution units, the CHAMP-AV9 offers a 2-4X performance per size, weight and power improvement over previous DSP modules.
-
-
Product
MW Signal Generators
-
The Lucid analog signal generator Desktop platform offers all the functionality of a fully featured full-size RF/MW signal generator in the smallest size module. You can use it as a desktop unit or easily scale up to hundreds of channels. Being a modular platform the Desktop signal generator is a solution for enabling customizing according to customers’ requirements and applications’ needs.
-
Product
FPGA Signal Processor
372
-
The Model 372 is designed around the Texas InstrumentsADS42LB69 16-bit ADC and the Analog Devices AD9788DAC. The 250 MHz sample clock is supplied by either theon-board frequency synthesizer or an external source. Thefrequency synthesizer can be phase locked to the local10 MHz TCXO or an external reference can be used toachieve system-wide phase coherence.
-
Product
Signal Conditioning Modules
-
Signal conditioning modules provide signal conditioning on a per-module basis for various types of sensor or signal.
-
Product
Signal Converters
-
ams signal converters contain four or eight signal channels, and can be dynamically programmed in-process by means of multiple amplification levels. This makes them very well suited for multi-channel sensor systems in applications with dynamic amplification and a high sensor bandwidth. All the converters small: they are available in space-saving (Q)SOP packages or as Chip-on-Board(COB) packages.
-
Product
PXI Vector Component Analyzer, 100 kHz to 32 GHz
M9816AS
-
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 22-24 AWG
610138109
-
Primary mating contact 610138216. (May mate with other ITA contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2-ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Signal Generator
-
Digital Signal Technology, Inc.
Electronic devices that generates electrical signals with set properties of amplitude, frequency, and wave shape.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
SSA Signal Source Analyzer, 10 MHz to 7 GHz, 26.5 GHz, or 110 GHz
E5052B
-
RF Input frequency range: 10 MHz to 110 GHz Analysis offset frequency range: 1 Hz to 100 MHz Phase noise measurement with ultra low noise floor and a cross-correlation method Frequency transient capture range: up to 80 MHz in narrow band, up to 4.8 GHz in wide band
-
Product
PXI Signal Conditioning
-
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
Product
Signal Chain µModule Receivers
µModule®
-
Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.
-
Product
High-Speed Signal Recording Systems
-
GaGe has a long history of providing high-speed, real-time signal acquisition, processing, and recording systems on PC-based platforms. This expertise saves customers time and eliminates uncertainties and risks with self-integrated systems.
-
-
Product
RF Signal Generators
-
As Rigol's RF first signal source, the DSG3000 series offers standard AM/FM/ØM analog modulation, as well as options for I/Q modulation and I/Q baseband output. The instrument is available with maximum frequencies of either 3 GHz or 6 GHz. Featuring a high signal purity with phase noise measuring <-110dBc/Hz@20kHz (typical) and a wide output range of -130dBm to +13dBm, the DSG3000 RF signal generator has standard pulse modulation with an on/off ratio of up to 80dB, with optional pulse train generator available. The DSG3000 series also has an amplitude accuracy of <0.5dB (typical).
-
Product
Minimal Signal Noise
SCSI Quiet Cables
-
Paralan Corporation was one of the first companies to recognize that 90% of the problems with SCSI Bus installations lie with the cables. To address this problem, Paralan developed its own line of high-quality shielded Quiet Cables.
-
Product
Digital Signal Processing (DSP)
-
Digital signal processing (DSP) affords greater flexibility, higher performance (in terms of attenuation and selectivity), better time and environment stability, and lower equipment production costs than traditional analog techniques. Components available today let DSP extend from baseband to intermediate frequencies (IFs). This makes DSP useful for tuning and signal selectivity, and frequency up and down conversion.
