Windows
-
Product
Beagle USB 5000 v2 SuperSpeed Protocol Analyzer - Standard Edition
TP322510
-
The Beagle™ USB 5000 v2 SuperSpeed Protocol Analyzer - Standard Edition is our lowest priced USB 3.0 model, and one of the most advanced USB 3.0 protocol analyzers available. Individually selectable options allow you to configure the analyzer to your specific needs today, while the fully field upgradeable design ensures this tool can evolve with your growing needs. Free Data Center Software and cross-platform support for Windows, Linux, and Mac OS X make the Beagle USB 5000 v2 SuperSpeed Protocol Analyzer - Standard Edition a user-friendly and versatile tool for any engineer working with USB 3.0 or USB 2.0.
-
Product
Digitizer
724 Family
-
The 724 is a family of CAEN Waveform Digitizer able to perform basic waveform recording and run online advanced algorithms (DPP) of pulse height analysis and dynamic acquisition window. Data is read by a Flash ADC, 14-bit resolution and 100 MS/s sampling rate, which is well suited for high resolution detectors as Silicon, HPGe or inorganic scintillators like NaI or CsI coupled with Charge Sensitive Preamplifers. In the waveform recording mode, algorithms of zero suppression are also implemented to reduce the data throughput. The acquisition can be channel independent and it is possible to make coincidence/anticoincidence logic among diferent channels and external veto/gating. Multiple boards can be synchronized to build up complex systems.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
SOP Managemen and Quality Management
arivis BM-Windream
-
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your data and document management that can be validated at relatively low cost (configurable standard software complying with GAMP5) and is easy to use. Users access your documents using a virtual network drive in Windows Explorer, which means that little training is required. BM-windream provides a standardised user interface over the entire life cycle of a file, from creation to deletion. At all phases in this life cycle, a change history (audit trail) is recorded. BM-windream is suitable for handling all kinds of non-managed documents. BM-Flow integrates directly with BM-windream and provides the document management functions required for SOP management,manufacturing instructions etc. All general employees can then still access the documents using the familiar Windows Explorer, while those responsible for creating documents can also use the workflow interface in BM-Flow.
-
Product
USB GPIB (IEEE-488) Interface
GPIB-USB-HS+
Interface
This compact USB - GPIB interface offers full function, IEEE 488.2 interface support via any computer with a USB port. The interface can control up to 14 GPIB instruments. The small size and light weight of this interface makes it ideal for portable applications using a laptop computer or for other applications in which the computer has no available internal I/O slots. The interface works with any Windows OS.
-
Product
100 amu CIS Analyzer
CIS200
-
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
Bio-Threat Detection & Collection
IBAC 2
-
The IBAC 2 is a fully automated bio-detection sensor that can support continual, 24/7, air monitoring or can be set to targeting sampling windows to align to hours of operation. It alarms in less than 60 seconds when a bio-threat is present. IBAC can be configured to support automated aerosol sampling either in conjunction with its’ triggered alarms or at a set frequency sampling time. In wide service throughout the world, IBAC 2 is used to collect and detect aerosolized agents for all four classes of biological threats (spore, viral, cellular, and protein toxins) with low false alarm.
-
Product
Elrec Pro Switch
-
The Elrec Pro Switch is a 10 channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC Pro also offers a Cole-Cole mode and twenty fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
Product
MIL-STD-1553 XMC Interface Module
XMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
System Design and Prediction Tool
MAPP 3D
-
MAPP 3D, a free software application for macOS and Windows, is a powerful, multipurpose sound system design tool that delivers precise, high-resolution predictions of sound energy distribution in a three-dimensional sound field. From preproduction to post-show analysis, work faster and smarter with the ability to streamline processes and consolidate designs in one simple, accurate 3D model.
-
Product
Broadcast Recording And Compliance Logging System
AMR130
-
The Mividi® Broadcast Recording and Compliance Logging System (AMR130) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that utilizes GPU encoding for low-cost video transcoding. The software supports stream recording, file management, editing and playback. The recorder takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous recording of 30 streams.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Portable Water Pressure Recorder
FJN-501
-
Completely water proof air sealed mechanism. Recording can be observed through the round window when the cover is closed. Compact, sturdy construction for easy portability. Durable, designed to hold up under hard use and with-stand corrosion.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Carbon and Sulfur in Inorganic Materials by the Combustion Infrared Detection Technique
844 Series
-
LECO combined our customers' feedback with innovative engineering to develop the CS844, an elemental analyzer designed for wide-range measurement of carbon and sulfur content of primary steels, ores, finished metals, ceramics, and other inorganic materials using the combustion technique. Our exclusive MS Windows®-based software, coupled with a boom-mounted touch interface, gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.
-
Product
WiFi Communication Module
WiFi-201
-
The WiFi module is without doubts one of the most advanced and innovating elements of NeuLog. Measurements with NeuLog sensors can be performed through any device which uses the Wi-Fi technology, such as iPads and Tablets with Android, PC computers with Windows / Linux or Macintosh with OS. These can all communicate with the Wi-Fi adaptor to begin a unique experience of data acquisition.
-
Product
GL Products Online & Interactive Demos
-
*NetSurveyorWeb™ is a centralized VoIP network monitoring system. A number of GL's PacketScan™ probes and/or,PacketProbes™ are deployed in remote locations across the network to passively monitor VoIP traffic. Whenever a monitored call completes, the scan/probe calculates a variety of quality metrics (MOS, loss, delay, jitter, etc) and sends the metrics to the central Oracle database for storage.**The PacketScan™ is a feature-robust Windows® based software tool that captures and monitors live IP traffic. In the VoIP world, it can monitor and measure SIP, H323, Megaco, MGCP, T.38 and video calls. In addition to quality metricsPacketScan™ also captures signaling information and sends that to the NetSurveyorWeb™ database as well.**GL's PacketProbe™ is an advanced CPE(Customer Premises Equipment) based VoIP monitoring reporting and diagnostic appliance, stemming from GL's suite of market leading voice analysis tools.
-
Product
IoT Device/ App Energy Optimization Tool
Otii
-
Otii is a developer tool for energy optimization of IoT devices and apps, created by developers for developers. The tool is easy to use, requires minimal setup, and lets developers measure and analyze energy usage at any stage of development. The Otii solution comprises a compact and portable source measurement unit, Otii Arc, and an easy to use, yet comprehensive desktop app for Ubuntu, Windows & macOS.
-
Product
Galvanostat and Zero Resistance Ammeter
-
This instrument offers a Potentiostat, Galvanostat and Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator in one. It is based around a two Amp Potentiostat teamed with a two Amp Zero Resistance Ammeter and can be supplied as - 6 channel, with six sequential channels, 8 channel (eight sequential channels) or 12 channel (twelve sequential channels). Connection to the controlling Windows PC is via a standard RS232 port, optically isolated for full floating operation. The instrument is supplied with a full set of cables and software, user manual and application notes on CD.
-
Product
Hand-In Type Electromagnetic Anechoic Box (Shield Box)
MY3720
-
Suitable for weak electric field resistance test, out-of-service test or digital forensics for smart phone, tablet terminal or mobile PC ! !DUT can be operated directly with bare hands while placing it in the box and looking at the inside from the shield window.
-
Product
Data Acquisition and General Purpose Test Equipment
-
All Fluke data acquisition products feature unique, built-in universal signal conditioning and a plug-in Universal Input Module to enable you to measure virtually any type of signal without having to purchase extra equipment. Plus, powerful, easy-to-use Windows®-based software supports easy configuration, advanced trend analysis, professional- quality reporting, and enables you to quickly build human-machine-interfaces without any programming.
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
Controller
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
Production and Laboratory OTDR
8000
-
The 8000 OTDR is the first of a new generation of OTDRs that has been designed specifically for optical fiber and cable test applications. Its revolutionary "performance first" optical design delivers unsurpassed optical performance, and its MS Windows operating system facilitates integration of the OTDR into manufacturing networks. These features, combined with unique data acquisition capabilities, significantly reduce the time associated with many aspects of the OTDR measurement process, making it possible for fiber and cable manufacturers to increase production output and reduce manufacturing costs.
-
Product
3 Digit LCD Voltmeter
DPM 600S
-
The DPM 600S is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, bandgap reference,auto-zero, auto-polarity and a set of annunciators. The meter can be panel mounted using the bezel and window. Connection to the meter is via solder pads.
-
Product
Universal Development Board For The PCAN-MicroMod CPU
PCAN MicroMod Evaluation Kit
-
As a plug-in module, the PCAN-MicroMod represents a simple way of providing electronic circuits with I/O functionality and CAN connection. The configuration is carried out with a Windows program that transfers the configuration data to the module via CAN. Several modules can be configured independently of one another on a CAN bus.
-
Product
Data Acquisition and Analysis Software
-
Matec Instrument Companies, Inc.
Matec provides a full suite of Microsoft Windows pc-based data acquisition and analysis software for your ultrasonic testing applications. In addition to our base software packages, our team of software engineers can work with you to develop customized scan forms and algorithms specific to your application demands.
-
Product
Switchboard Meters
-
Hoyt Electrical Instrument Works Inc.
Glass window, ABS Resin frame and case, PC glass fiber base Mounting fittings included. Black base and frame, white scale plate and meter body.
-
Product
Digital "A" Flow Controller for High Flow
HFM-D-306A / HFC-D-308A
-
Mass flow techniques provide reliable, repeatable and accurate gas flow rate measurements.HFM-D-306A/HFC-D-308A mass flow instruments have flow ranges from 0-2500 slm to 0-10000 slm; provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available. Available with a variety of elastomer seals for maximum flexibility.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
