LED Sensors
-
Product
Contact Temperature Sensors
-
A thermoelectric device for measuring temperature, consisting of two wires of different metals connected at two points, a voltage being developed between the two junctions in proportion to the temperature difference.
-
Product
Multipoint Temperature Sensor
TSM800
-
The TSM800 multipoint temperature sensor is ideally suited for measurement of process temperatures over multiple locations with a single access point.Typically used in process plant vessels the TSM800 provides a cost effective alternative to mounting multiple individual sensors and their associated process vessel entries.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Lightning Warning Sensors
-
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
Product
Gas Flow Sensors
ESRF-ESF Sensor
-
ESRF-ESF is one of the few gas flow sensors featuring bidirectional gas flow sensing of up to ±300 ln/min with a total error band of < 1.25% RD. ESRF-ESF gas flow sensors provide calibrated and temperature compensated output on an SPI, I2C bus or analog output making them plug & play for direct interfacing to low voltage MCUs and systems. The user is provided with a multitude of interface and output options so that the right sensor configuration can be selected based on the specific requirements for each application.
-
Product
Process RF Sensors
-
Process RF (radio frequency) analyzers using penetrating radio waves to determine the moisture content across a full sample thickness. Single point, array and hand-held analyzers provide a variety of sampling options from fully integrated in-process moisture profiling to at-line quality control. RF analyzers are widely used in gypsum, panel board, and other industrial processes.
-
Product
LED LIGHT DISTRIBUTION TESTER
-
Essential elements among LED inspection categories are the light quality and intensity. Accurate measuring for optical characteristic requires diverse photo-measurement technology which fits into production lines. This system extracts conditions necessary for optical measuring optical characteristics on production equipment through accurate measurement both of the quality and of intensity of LED light distribution characteristics.
-
Product
Clamp Sensors
-
Kyoritsu Electrical Instruments Works, Ltd.
Can measure AC current up to 1000A Flexible and light weight by the air core coil used at the sensor part Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
LT-300A Aging-Life Test System For LED Luminaires
-
Hangzhou Everfine Photo-E-Info Co., LTD
LT-300A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
Product
Capacitance Sensors
-
Designed for continuous level measurement of conductive, non-conductive liquids and other fluid types. Available in many sizes and with a variety of features.
-
Product
Inductive Sensor
Ampstik®
-
The Ampstik is easy to use and provides accurate information to anyone working with medium and high voltage. It gives line personnel the right answers so they have the ability to make decisions in the field.
-
Product
Linear Hall Sensor
-
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
Product
Optical Sensors
-
Broadcom offers a wide range of optical sensors solutions including ambient light, RGB color, proximity and gesture sensors for a broad range of applications including:*Mobile / Computing - smart phone, tablet, laptop, gaming mouse, printer*Consumer Electronics – TV displays, handheld game console, digital camera*Lightings – Industrial / commercial lightings, residential lightings, outdoor street lightings*Automotive – Instrument panel illumination*Medical Diagnostic Equipment*Industrial Instrument*Contactless switches*White Goods*Sanitary Products*Health / Fitness Products
-
Product
Single Channel, ±40 V, 100 MHz, 40 NA – 1 A
CX1101A
Power Sensor
The CX1101A single channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide common mode voltage range. The maximum current can be expanded to 10 A using a CX1206A.
-
Product
Photoelectric Sensors / Laser Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers some of the smallest Photoelectric Sensors in the world and include sensors with or without a built-in amplifier. With advanced features such as background/foreground suppression to protect against unwanted detection and the choice of built-in amplifiers that provide the same high-speed response and built-in features that can be found in high-end Fiber Optic Amplifiers, Panasonic can ensure the highest quality sensing available to meet any application requirement.
-
Product
Sound Velocity Sensors
SVP 70
-
Compact and robust, the SVP 70 features a long path length whether you install it on a survey vessel, or take it down to 6,000 metres on an ROV, AUV or submarine.The SVP 70 is an all-titanium plug -n- play system with RESON SV processors, wide input voltage and RS232 and RS422 communication interfaces for long cable runs.
-
Product
10 MHz To 54 GHz LAN Wide Dynamic Range Average Power Sensor
L2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Stud Sensors
-
Stud Sensors such as the MSV100 and MSV350D comprise a category of their own. Each uses electromagnetic induction to sense the presence of (and thereby locate) a stud, pipe, batten, current-carrying wire or other metallic object behind a wall or above a ceiling. The two instruments differ in their choice of the display technology (LED or LCD) used to pinpoint position.
-
Product
GS1 Acceleration Sensor
AGS11351
-
Panasonic Industrial Devices Sales Company of America
GS1 Acceleration Sensor
-
Product
10 MHz to 6 GHz/33 GHz LAN Power Sensor
U2049XA
Power Sensor
Wide dynamic range (-70 to +20 dBm) for small signal measurements LAN/ Power-Over-Ethernet (PoE) connectivity for long distance remote monitoring (up to 100 meter)TVAC compliant for operation in vacuum Best-in-class long term drift performance Internal zero and automatic calibration saves time and reduces measurement uncertainty Easy measurement start-up with new intuitive BenchVue software
-
Product
Automotive Sensors
-
Vehicle electrification (e-mobility), sustainability (zero emissions), increased safety & productivity are trends significantly impacting the role of sensors in passenger and commercial vehicles. This includes the requirement to enable greater e-motor performance and efficiency, reduced charging time, increased battery life, cleaner and more efficient internal combustion engines, reduced maintenance / vehicle down-time as well as highly robust ADAS and autonomous driving safety systems. TE offers a diverse sensor technology portfolio, combined with deep application expertise gained from extensive experience of delivering quantifiable value across a wide range of demanding passenger & commercial vehicle applications.
-
Product
Sensor
VL53L1
-
The VL53L1 is a state-of-art Time-of-Flight (ToF) laser-ranging miniature sensor. Housed in a miniature and reflowable package, it integrates a SPAD (Single Photon Avalanche Diodes) array, physical infrared filters and optics to achieve the best ranging performance in various ambient lighting conditions, with range of cover glass options.Unlike conventional IR sensors, VL53L1 uses ST’s latest generation direct ToF technology which allows absolute distance measurement whatever the target color and reflectance. It provides accurate ranging up to 4m and can work at fast speed (60Hz), which makes it the fastest miniature ToF sensor on the market.With patented algorithms and ingenious module construction, VL53L1 is also able to detect different objects within the Field-of-View with depth information (histogram) at 60Hz. Scene browsing and multi-zone detection is now possible with VL53L1, thanks to software customizable detection array for quicker “touch-to-focus” or mini depth-map use cases.
-
Product
Tailgate Sensors
-
Protect your GMC MultiPro™ or Chevrolet Multi-Flex™ tailgate from costly damage! This no-splice hitch cap sensor detects when a shank is installed in the receiver and prevents the inner tailgate from folding down. It is available in multiple hitch sizes and is perfect for any hitch accessory.
-
Product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
-
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
Sound Velocity Sensor
miniSVS
-
The Valeport miniSVS uses digital "time of flight" technology to provide the lowest noise, highest accuracy, best resolution sound velocity data available.
-
Product
PIR Sensor With LED Signal
555-28027
-
The PIR Sensor detects motion by measuring changes in the infrared (heat) levels emitted by surrounding objects. When motion is detected a LED lights up the lens dome as a visual signal, and the module also outputs a high signal on its output pin.
-
Product
Web Sensor
P2520
-
Converter Web Sensor P2520 is designed for the connection two sensors with current output into Ethernet network. The measuredcurrent (0-20mA or 4-20mA) can be converted to the physical quantity that is measured by the connected sensor. The converter isgalvanically isolated from the Ethernet communication lines, current inputs and power supply are not galvanically isolated.
-
Product
Spot Sensor
SP 1000-20R1
-
Advanced Thermal Solutions, Inc.
The SP 1000-20R1 is a single-sensor probe designed for measuring the surface temperature of solids. Its small size allows for the exact positioning of the sensor at the desired spot. The size of the sensor eliminates any conductive heat transfer that may occur through the lead wire, enhancing measurement accuracy.
