Mixed-Signal Test
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed Signal Testers, MIxed Signal Test Systems
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
Product
Eggplant Test Automation
-
Keysight Eggplant Test 7.0: Test automation software designed to streamline testing and reduce associated risks with manual do-it-yourself testing on any platform.
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Test Finger Apparatus
-
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy.
-
Product
DC Insulation Testing
-
Diagnostic insulation testing today represents over a hundred years of constant development. When Sydney Evershed pioneered the first insulation tests in the late 19th century, the only measurable values were insulation at 500 volts and a basic continuity check. However, measurement techniques have continuously evolved to keep pace with new insulation technologies. From electronic design and household wiring to generators and power transmission systems, all different kinds of insulation must operate at a safe minimum value.
-
Product
NVMe Testing Software
IOL INTERACT™
-
IOL INTERACT™ software expedites and automates the testing of NVMe SSDs and NVMe-oF products. It is used to test products for inclusion on the NVMe Integrator's List. Members of the UNH-IOL NVMe Testing Services are entitled to a copy of INTERACT™ for in-house testing to ensure that their products will meet the Integrator's list requirements when submitted for testing. While most test requirements can be performed with the PC edition tool, a subset of tests specific to PCIe products are only available on the Teledyne-LeCroy tool, which require low level traffic generation capability.
-
Product
ERP Testing
-
Signing up for an ERP package is a big decision for any enterprise since it is closely related to key business processes and has the potential to significantly enhance the customer service and experience. To ensure an optimized return on investment, it is critical to have a successful roll-out with the desired features and benefits. With a high failure rate for ERP implementations, it is very crucial to have a comprehensive QA strategy and expertise. TestingXperts offers you specialist QA and solutions for ERP testing and ensures that your ERP systems function properly and meet your business needs. We have subject matter expertise on leading ERP QA packages, coupled with best-in-class QA processes, frameworks and accelerators to help you achieve your ERP goals. Our expert ERP software testing experts have the ability to test features of core applications end to end and also keep pace with the evolution.
-
Product
Concrete Testing Gauge
-
Beijing TIME High Technology Ltd.
A general term for devices used to measure properties of concrete.
-
Product
Wireless Device Testing
-
D.L.S. Electronic Systems, Inc
WI the testing and certification of your Wireless Device will be accomplished with precision and efficiency.
-
-
Product
D-Mic Testing System
BK3012V2
-
Easy to use and faster than human testers can load, the new BK3012V2 is the upgrade of our popular BK3012 D-Mic tester. Setup is even easier than for the BK3012 and you can enter specifications and be ready for testing in a few minutes. As well as testing, the BK3012V2 can be connected to a computer, so you can keep your results and analyze them for current quality and trends over time.
-
Product
EMI Test Receiver
ESR
Receiver
The R&S®ESR is an EMI test receiver build to measure electromagnetic disturbances using conventional stepped scans or ultrafast FFT based time domain scans. It also functions as a powerful signal and spectrum analyzer. The receiver features real-time spectrum analysis with a wide range of diagnostic tools for detailed analysis of disturbance signals and their history.
-
Product
ICT: In-Circuit Testing
XILS In-Line Handling Solutions
-
Designed to cover a large number of test points, with long panels for future expansion, the XILS series of Handlers, PCB test systems in the line of EIIT - Innovative Engineering Solutions, is ready for the most demanding applications.
-
Product
Lightning Test
-
Lightning testing is used to determine the ability of externally mounted electrical and electronic equipment to withstand the direct effects of a lightning strike.
-
Product
Test Pattern Generators
-
Video Test Pattern Generator, Portable Monitor Tester, Test Video Audio Signals, HDMI, DVI, SDI, Component Video, HDCP
-
Product
Measuring and Testing Equipment
-
Bott's measuring and testing equipment offers a multitude of advantages, making it attractive for a wide range of applications. Its modular and scalable design allows for flexible use – from individual workstations to fully integrated, automated test lines. It operates safely and in accordance with standards, complying with all relevant safety and industry standards such as DIN VDE and IEC, which makes it particularly reliable in sensitive application areas.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Sensors Test Cells
Integrated MEMS
-
The best technical performance, cost optimization, one-shot factory integration.A single unit integrates the modules for the handling, contacting and complete testing of MEMS devices, including the physical stimulus for functional test, and the tri-temp thermal conditioning.
-
Product
FPGA Testing
-
Silicon Turnkey Solution, Inc.
The secret to our success in the FPGA testing field is the STS hammer file, a proprietary test methodology based on our experience testing thousands of unique FPGA designs. The hammer file is designed to program the FPGA to its maximum combination and block configuration and then tests the completely programmed FPGA for full dynamic, DC and at-speed AC performance. Power and transient tests are also conducted under worst-case populated configurations. Application-specific usage configurations are also used to assist in generating the worst-case electrical specification limits at worst-case environmental use.
-
Product
Test System
2000/DATS
-
WesTest Engineering Corporation
The WesTest-2000/DATS features Teradyne's high performance Digital Test Instrument and state-of-the-art intrsuments from Agilent, Elgar and North Atlantic.
-
Product
Test Stands
-
We develop modern and flexible test stands for research, development and production. In doing so we exclusively use our own in-house imc measurement hardware and software platform that has become established in the testing market worldwide. Our experienced “customer solutions team” is at your side during all phases of project development: from planning and construction through to configuration and implementation phases. We are also more than pleased to support you in modernizing and retrofitting existing installations and protecting your investment in the future.
-
Product
Multi-Cell Test System
Cellcia
-
Next-generation wafer probing system for 300mm wafers. The multi-layer system structure maximizes the efficiency of testing, further reducing the total testing cost.
-
Product
Full-Cycle Testing
-
We perform all types of testing: Functional, GUI, Usability, Security, Database testing, Cross-platform, Cross-browser, Accessibility, Installation, Configuration, Localization, Performance/Load, Stress testing etc.
-
Product
Battery Test Packages
-
Explorer Technology Group (ETG)
ETG offers a full range of battery test kits which speed and simplify the process of collecting battery test data . This data can then be downloaded and analyzed with the included Winmeter 5.1 Battery Analysis Software, enabling the user to quickly identify batteries that are likely to require preventative maintenance.
-
Product
Electrolyzer Test Systems
-
Advanced Test System for Research & Development of PEM Electrolyzers
-
Product
Test Connector Components
-
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
Product
Fire & Flammability Test
-
Fire & Flammability testing: ASTM E119 [UL 263]; ASTM E152 [UL 10C]; ASTM E814 [UL 1479]; API 607, 6A; ASTM E108 [UL 790]; UL 1709; UL 1715; UL 2043; NFPA 286; UBC 26-2; UBC 26-3; ASTM E84 [NFPA 255, UL 723]; ASTM E162; ASTM E662 [NFPA 258]; ASTM D635; ASTM D1929; ASTM D2863; ASTM E1354; ASTM E1317; Room Burn Facility; CAL 133, 117, 129; UL 94 V/HB; IMO A.652 (16); IMO A.653 (16); ULVW I; ASTM D2859; AITM 2.0007; NFPA 701; FMVSS 302; FAA 25.853; IEEE 383
-
Product
Meter Test Systems
-
We offer a huge variety of products for meter testing. From the smallest device with the size of a single-phase meter up to customized semi-automatic systems with more than 40 test positions.
-
Product
Dynamics & Vibration Testing
-
Vibration testing ensures that your new design will survive in its intended environment. Submitting your product for vibration testing or analysis pays for itself by reducing field return costs through improved product reliability.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
