Pulse Current
-
Product
Hand-Held, Battery-Operated Multi-Frequency Eddy Current Instrument
US-454A
-
United Western Technologies Corp
The US-454A is a portable, hand-held, battery-operated multi-frequency eddy current instrument that can be connected to a laptop, PC and motion controllers for use in semi- or fully automatic data collection applications. Two encoder inputs enable position stamping of data. Pulse-on position input is ideal for motion control applications. Ethernet and USB capabilities allow instrument control along with time- and position-stamped data transfer to the client computer. Built from the rugged US-454 architecture, the US-454A offers single- and multi-frequency inspection, frequency mixing capabilities, enhanced signal-to-noise ratio, USB, Ethernet and data storage capability, and unprecedented digital strip chart data collection.
-
Product
THz Pulsed Imaging and Spectroscopy
TeraPulse 4000
-
TeraView’s proprietary semiconductor technology gives the TeraPulse 4000 a market leading signal-to-noise specification with over 90 dB at peak. As standard, the TeraPulse offers a bandwidth of 60 GHz up to typically 4.5 THz; with an option to extend this beyond 6 THz.
-
Product
Thin Film Current Sensing Chip Resistors
CSTN
-
*Thin film process*High power rating up to 3 watts in 2512 size*Resistance values from 50m to 1ohm*High purity alumina substrate for high power dissipation*Power management applications*Switching power supply*Over current protection in audio applications*Voltage regulation module (VRM)*DC-DC converter, battery pack, charger, adaptor,*Automatic engine control*Disk drive
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
43-752A-901
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-02
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Primary Current Injection Kits
-
During installation,testing,especially if the protective gear is connected to the power line via a current transformer it is advisable to use our Primary Injection Test Set. Keeping this in mind a wide range of Primary Current Injection Test Sets are being manufactured by "NMC”.
-
Product
Leakage Current Clamp Mete
-
Basic functions:AC current:20mA resolution: 0.01mA, ± (2.5%, +5)200mA resolution: 0.1mA, ±(2.5%, +5)2A resolution: 1mA, ±(2.5%, +5)60A resolution: 100mA, ±(3%, +8）AC voltage: 600V, ±(0.8%, +5)DC voltage: 600V, ±(0.8%, +5)Special functions:Auto ranging Low battery display Data hold Auto power-off Over-load protection Input impedanceDC voltage measurement: ≥10MΩ Sampling frequency: 3 times/s Maximum display: 1999 Maximum distance between clamps: 30mm General characteristics:Product colors: iron-gray and redProduct net weight: approximately 136gLCD size: 25x36mmProduct size: 183x63x29mmPower: 2x1.5V, 7#Standard accessories: packing carton and handheld bag English user's manual and battery
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
Magnetic & Current Sensors
-
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable
T3RC0060-LF
-
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable.
-
Product
True RMS Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Current clamps are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. In addition, this model has extensive multimeter functions for voltage, resistance, frequency, capacitance and temperature measurement.
-
Product
Eddy Current Dynamometer
EC Series
-
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
Product
Laboratory EM current meter / water level and wave height meter
-
ACM2-RS and ACM3-RS are 2-D and 3-D electro-magnetic current meters for laboratory experiments. The models provide digital output, a high-speed sampling rate and insusceptibility to electro-magnetic noise. ACH-600RS is a highly sensitive capacitance water level meters. With the new system, a maximum of four different sensors can be connected to the compact interface unit, enabling simultaneous recording on a personal computer. Additionally, the system can provide analog output as well as necessary. While conventional water level and wave height meters cannot be used near velocity sensors, our instrument can be as near as 5 cm without increasing noise, due to its special isolated circuit. The result is an innovative system that is capable of achieving highly accurate data.
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
-
Product
PXI/PXIe Wide Current Range Matrix Module, 6x4, 2-Pole, X & Y Loop-thru
42-514-002
Matrix Switch Module
The 40-514-002 (PXI) and 42-514-002 (PXIe) are low density matrices in 6x4 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-100
-
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
Frequency-Resolved Optical Gating Pulse Analyzer
IQFROG
Analyzer
The IQFROG measures pulse intensity and phase in both spectral and temporal domains, yielding a complete pulse characterization. With its long delay arm and high resolution spectrometer, it measures chirped pulses up to 50 ps wide, or up to 10 ps wide if the pulse is transform limited. The IQFROG is available in 1.0 and 1.5 micron wavelengths.
-
Product
Triaxial Cable For Current Higher Than 1 A (1.5 M Or 3 M)
16493L
Coaxial Cable
16493L can be used as a general purpose triaxial cable for high current applications up to 4.2 A DC and 200 V. It can also be used for low current applications down to the sub-pA level.
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Split type AC Current Transformer
CTS-200
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
Product
Calibrator, Calibrated w/Data, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL D
-
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
Product
Flex Power Right Angle Non Shut-Off Pulse Tools
-
The non shut-off right angle pulse tools are ideal selection when the operator needs to control the fastening process. It offers access for hard-to-reach fasteners in tight spaces. The drive on a right-angle tool is mounted at a 90-degree angle to the tool body. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Profiling Current Meter and Wave
SeaGuardII DCP Wave
-
The SeaGuardII DCP Wave is a 600kHz Doppler Current Profiler able to measure directional wave parameters and currents from a bottom mounted installation.The Acoustic Wave software 5759 used by the DCPS implements unique features to improve the wave measurement accuracy by optimizing the signal to noise ratio.Maximum deployment depth is 40m in normal scatter conditions. The Profiling Current Meter and Waveis available as a self-recording instrument. It can be easily integrated into a real-time system offering reliable two-way communication.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ALCL-40D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for micro ampere current measurements.*Super high accurate sprit type ZCT sensor.*High sensitivity and least affection from external magnetic field. (less than 10μA for 400A nearby conductor)*For leakage current measurements of arrester.*Stable measurements under high electric field and strong magnetic field.
-
Product
DC Earth Leakage Current Measurement
DCZCT-11M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC Earth Leakage Current Measurement *Bipolar DC ±12V Power Supply*Output DC ±1.5V at DC 10mA *Isolated Housing Case based on UL94V-0*Through Hole PCB Mount Type, Exciting Current Method
