Battery Impedance
-
Product
Battery Monitor
BAF-M2
-
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Heavy Duty Wheeled 12V/24V Battery Powered Jump Start Systems
Boost-All
-
A jump starting solution for repair shops, parking lots and garages. While not designed for continuous jump starts, the Boost•All® offers economy without skimping on quality. This unit provides 12/24V, battery powered jump starting in a narrow, 20” wide portable unit with makes maneuvering between rows of parked vehicles a snap.
-
Product
Handheld Battery Powered Digital Synchro Meter
DSM-4
-
The DSM-4 is the handheld battery powered digital synchro meter with a large four digit LCD display. It is auto-ranging to accept virtually all standard military synchro signals. The DRM-4 is a handheld battery powered digital resolver meter. A dual range switch provides compatibility with all low-level resolvers ranging from 3.5V to 14V.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
-
Product
Automatic Battery
BATLV800
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Car Battery Analyzer
TE6-0602
-
Hangzhou Tonny Electric & Tools Co., Ltd.
For DC12V car battery test. Plugs conveniently into any vehicle cigarette lighter socket, Measure remaining power, Compact and easy to store, Easy to read light meter
-
Product
Consumer Battery Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
Many electronic products are around our daily life nowadays, smartphones, tablet, wearable devices, laptops, home robots, etc. The rechargeable battery, mainly Lithium-ion battery are widely adopted in such products. There is a greater demand for battery safety testing from both battery and product manufacturers. They should make sure the battery is qualified before delivering it to customers. As a lithium battery test chamber supplier, DGBELL dedicated to the R & D of battery safety tests in China with many technical patents. In this 10 years experiment of researching and manufacturing, we keep developing new equipment and improving the battery test system from cooperating with thousands of customers. DGBELL dedicates to provide a reliable and comprehensive solution for lithium battery test chambers, matching the standard IEC 62133, UN 38.3, and UL 1642. Including mechanical, electrical and temperature environmental test chambers.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Known impedance for use in loudspeaker measurements
Impedance Box
-
An impedance box is necessary for measuring the impedance of a loudspeaker. Listen Inc.’s impedance box contains a 0.25Ω resistance. This value is suitable for most loudspeakers, but may be easily swapped out for a different value by the user if speakers with a particularly high or low impedance are being tested. It is available with either XLR or 1/4″ balanced connectors. Please specify type of connectors when ordering.
-
Product
Lipo Battery Power Level Tester & Alarm to Indicate Low Power
#52023
-
Can be used for 7.4V (2S pack)and 11.1V (3S pack).Red LED will flash when cell is below 3.3V and an Alarm will sound when cell is below 3.0V indicating the Lipo Battery pack should be recharged.
-
Product
High Impedance Differential Relay
-
High impedance protection schemes are widely used for the protection of BUS bars, generators, motors & power transformers. BUS bar protection schemes utilizing electromechanical high impedance differential relays are often used due to their simplicity, reliability & comparatively low cost.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
Battery Test Software
-
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
Product
Battery Electrical System Analyser
-
We invented the “Resistance method” which uses a series of shorting pulse to measure the voltage drop in order to calculate the plate’s internal resistance. Unlike other patented “Conductance method” which generates an AC pulse across the battery terminal to measure impedance.
-
-
Product
Battery Discharge and Capacity Testers
-
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
Product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
-
Standard Electric Works Co., Ltd
● Protection class: IP65● Bright LED visual indication● Audible indication● Non-contact voltage detection: 220Vac ~ 132kVac● Wide angle voltage detection● Frequency range: 40 ~ 70Hz ● Easy-to-prove method● Self-test function● Power source: 9V rechargeable battery ● Non-contact detection by proximity● Flashlight function● Operating temperature: 0°C~50°C● Humidity: 80% RH Max● Lightweight, robust and compact● Comply with EN 61326-1
-
Product
Battery Capacity Analyzer
-
Foresight Electronics Co., Ltd.
At present, Iead acid storage battery’s maintenance is applied for the check of Float voltage of battery at home, it has been found that Voltage is irrelevance with Capacity of battery, because Voltage is only to show battery’s basic parameters.Internationally, Resistance test is widely applied in daily battery maintenance instead of Voltage check, because Resistance is reflection to internal parameters of battery with high precision worldwide.
-
Product
Fixed Batteries (Constant Function)
-
Lifasa - International Capacitors, SA
Fixed compensation equipment has different variants depending on the type of enclosure / support and the configuration of the equipment (type of capacitor).
-
Product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
-
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
Product
Battery Maintenance & Test Equipment
-
Fuzhou Fuguang Electronics Co., Ltd.
Battery Maintenance & Test Equipment
-
Product
Battery Module/Battery Pack Test
-
The battery test system CT3001B and CT3001D provide solutions for battery module/battery pack test with higher current/voltage. They can also be used in situations that batteries are charged/discharged at high rates. Different current/voltage range and channels numbers can be custom made based on the requirement.
-
Product
Battery Discharge Capacity Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Impedance Monitors
-
Single channel impedance monitorA flexible frequency generator/analyzerSupporting external load/potentiostat - TDI Dynaload RBL488 series & XBL series - WonATech WEL Load - Other 3rd parties potentiostat/galvanostat
-
Product
Battery Test System
WBCS3000Ls32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
