Serial Data
-
Product
Handheld Serial Data Analyser
SDA-02
-
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
Product
Interface Adapters and Serial Data Repeaters
-
Designed to provide a fan-out of up to ten RS-232 compliant outputs from a single input, the SSD120-100N-SDR is an all solid-state Serial Data Repeater. This device provides a simple and robust means of transmitting serial data to multiple aircraft systems in a small package.
-
Product
Serial Data Converters
CONV232/485 and CONV232/422
-
CONV232/485 and CONV232/422 convert between RS-232 communications (as used by the COM1 and COM2 ports standard on most motherboards) and balanced-mode, long distance RS-485 and RS-422 communications. CONV232/485 was designed for use with our REMOTE ACCES line when there is no RS-485 port on your PC, but may also be used in other, similar applications.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
Digital Serial Data Audio Interface
PIO-9216
-
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
Product
Compatible Bi-Directional Serial Data Interface
PMC-BiSerial-IO-II
-
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
ULI-211E - Heavy Industrial RS-232/422/485 (Terminal Block) To Multimode Fiber (ST Connector). Panel Mount Metal Chassis
BB-FOSTCDRI-PH-MT
Terminal Block
Converts serial data signals to multi- or single-mode fiber2 KV, 3-way isolation (input, output, power circuits)Data rate: 9.6 to 115.2 kbps (bit-wise enable)-40 to +85°C wide operating temperatureIP30 metal panel mount case (DIN rail adaptable)FCC, CE, IEC-61850-3, IEEE 1613, UL C1/D2Note: 2 units required to extend data via fiber optic connection (see datasheet)10-48 VDC power source required (not included, sold separately)
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
3U Processor Board
CP39104
-
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
1553Guard
-
MIL-STD-1553 bus architecture is a threat that adversaries can leverage to compromise your equipment and spread malicious software through your Serial Data Bus (SDB) system. You need a solution that can not only identify current and future cyberattacks in real-time but also instantly eliminate those threats before they wreak havoc and interrupt the mission.
-
Product
Ethernet to CAN Bus Gateway
YAV90090
Ethernet Interface
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
PXI 18 Channel Data Comms MUX, 96-pin SCSI
40-735-902
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Jitter Noise Generator
J7000
-
The J7000A Series instruments high crest factor output is used as a random jitter source for serial data bus applications, including PCI Express Gen I & II, Serial ATA, and Fiber Channel. The noise source is designed for the PCI-SIG total jitter (Tj) model serial data application, but can be used for any random jitter noise application.
-
Product
PC/104p Compatible Bi-Directional Serial Data Interface
PC/104p-BiSerial
-
The PC/104p BiSerial has been ported from the PMC BiSerial II. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PC/104p--BiSerial. The BiSerial features completely isolated FIFOs with 32 bit ports for increased adaptability and performance
-
Product
WaveMaster Oscilloscope, 6 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 806Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
VME Module
ICC-8-xxx
-
The ICC-8-xxx is the second generation of the ICC-8 board. Enhancements includes true RS-485 communications with jumper configurable I/O by the user. The ICC-8-xxx is a VME based, 8 channel intelligent and versatile solution to serial data communications designs.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
WaveMaster Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 804Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
-
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
Product
Oscilloscopes
Oscilloscope
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities - typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
-
Product
RS232 / RS485 / RS422 / TTL Serial Repeaters & Hubs
-
CommFront offers a range of rugged, industrial-grade RS232 / RS485 / RS422 / TTL repeaters and hubs to meet serial communications' data distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
PAM analysis upgrade for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-UPG-PAM
Analyzer
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
Product
Serial to Parallel Analysis Package
B4601C
-
Your system uses serial buses to communicate between ICs and transfer data to and from peripheral devices. Sifting through thousands of serial bits by looking at long vertical columns of captured 1's and 0's can be very tedious, time-consuming, and error prone. The Keysight Technologies B4601C serial to parallel analysis package is general-purpose software that allows easy viewing and analysis of serial data.
