IRIG
Inter-range instrumentation group time codes.
-
Product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
-
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
-
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782110-01
Synchronization Module
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module—The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
Flight Termination Test Set
-
Kratos Defense & Security Solutions, Inc.
The FTTS accepts AC power and generates a modulated RF output suitable for interrogation of flight termination receivers and/or command receiver/decoders. The FTTS can transmit up to 6 tones simultaneously and the RF output power is adjustable from 0 to -127 dBm. The IRIG tones can be switched ON/OFF independently from the control panel. A 20 Tone version of the FTTS is also available.
-
Product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
Product
8" Cable
CONW1553-1
-
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
Product
VME Time & Frequency Processor
VME635091-SyncClock
-
Brandywine Communications’ VME635091-SYNCCLOCK is a time and frequency processor module that provides precision time and frequency reference to the host computer and peripheral data acquisition systems. Time is acquired from time code signals, typically IRIG B. Time is displayed on the front panel (hours, minutes, seconds) via LED digits.
-
Product
Countdown Or Countup Clock Controller
RC600
-
The RC600 is a remote control that adds both countdown and countup timer control features to our NTDS and TCDS clocks. Reference or generate time input from NTP or time code (IRIG & SMPTE). Control a virtually unlimited number of time code clocks and network clocks.
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
Receivers
-
Designed to demodulate IRIG destruct tones, this receiver uses an up-converting superheterodyne configuration for high dynamic range and image rejection and has a receive sensitivity of better than -107 dBm. Originally developed to monitor/verify Range Safety Command Destruct Transmitters, it is a compact rugged design usable wherever a high tolerance to shock, vibration and temperature is required.
-
Product
Aerospace Testing Solutions
-
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
Product
CPCI timing plug-in
CPCI-SyncClock32
-
The CPCI-SyncClock32 from Brandywine Communications provides precision time with zero latency to the host computer over the CPCI bus in the 3u form factor. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or Have Quick.
-
Product
ARINC 429 XMC Interface Module
XMC-429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable high/low speed operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - IRIG‐B time code encoder/decoder for data correlation - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - ANSI Application interfaces supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, and VxWorks (others provided upon request)
-
Product
Aerospace Interfaces
-
Aerospace InterfacesDecode and visualize data from ARINC 429, MIL-STD-1553, IRIG CHAPTER 10, iNET and IRIG Chapter 4 PCM telemetry data interfaces.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
-
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Dual Channel Multi-function Decommutator
LS-55-DD
-
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
Product
Automated Telemetry Test Station
ATTS5000
-
Systems Engineering & Management Company
The ATTS 5000 was developed by SEMCO to ensure that receiver systems successfully perform at both IRIG 118 Chapter 4 recommended tests, as well as additional customer-specified performance parameters. The ATTS 5000 ensures that the highest quality test data is consistently and repetitively collected on each and every system.
-
Product
GPS Master Clock
-
Signals & Systems India Private Limited
GPS Master Clock System – MCS-GPSMC-1010 is a 3U Card rack type, 19” Rack-mountable Redundant GPS Time Server which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from any one of the sources like GPS or GLONASS or Time protocols such as NTP and IRIG. It distributing the same time signal through several types of interfaces. It provides redundancy for Power and GPS receiver to increase reliability and offers protection against time synchronization failure. The system is field-upgradeable and an extremely flexible system, designed to handle time synchronization requirements today and in the future. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, DCF77, BCD parallel data, Ethernet Fiber Optic & RS485/RS232 outputs. System enables configuration and monitoring through Web-based application. It supports a wide range of power supply either 90V-260V AC/DC or 18-36VDC or 36V-72VDC. Power supply model can be mixed and matched as required by the user, depending upon power supply options available at the installation site.
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782109-01
Synchronization Module
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module - The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified … synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
PCI Express Timecode and GPS Reader Generator
PCIEX-SyncClock
-
The PCI-Express time code reference timing card with standard options such as IRIG B and optional GPS receiver provides an extremely accurate time source to the PCI-Express bus.
-
Product
IDM+
-
Multi-functional fault recorder including: -- Disturbance fault record (DFR)- Dynamic disturbance recording (DDR) - Phasor measurement unit (PMU C37-118)- Power Quality (PQ Class A)- Travelling wave fault location (TWS to +/-60m) - Impedance fault location- Protocols (61850, Modbus, DNP3) - Sequence of event recording (SOE)- GPS, IRIG and NTP time sync- iQ+ masterstation software.
-
Product
IRIG Time Code Receiver & Generator Module
TCR180
-
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
Product
GPS synchronized NTP Server
NTV-100
-
Brandywine Communications NTV-100RG is an affordable, convenient and flexible NTP Server. This network time server accurately time synchronizes computers, time displays, PBX’s, and a wide variety of other equipment. The NTV-100RG is a small, rack mounted NTP Server that can synchronize to GPS or to the IRIG B time code to provide NTP time.
-
Product
Time Measurement Equipment
TimeSpy
-
The TimeSpy precisely measures the time accuracy of a wide range of inputs (such as: NTP, IRIG B, 1PPS, and ASCII) against an internal precision GPS-controlled oscillator, displayed on the large, full color windows-based touch screen. The TimeSpy can precisely measure the time error at the point of use for systems where time is distributed over large distances. The TimeSpy can also measure free-running clocks and timing systems which are synchronized from untraceable sources, such as television and radio broadcasts, electrical power lines and the internet.
-
Product
Rack-Mounted Timing Systems
CommSync II Family
-
The CommSync II family of modular systems provide GPS time and frequency outputs to meet your synchronization requirements. All systems include support for multiple input and output modules including 1PPS, IRIG, HAVE QUICK, PTTI, IEEE-1588 PTPv2, low phase noise 1, 5, and 10 MHz sine wave as well as custom outputs.These systems are available with military SAASM MPE-S GB-GRAM, SAASM Force 22E MRU or civilian C/A GPS receivers. Rubidium or OCXO oscillators provide for excellent holdover performance in the event of failure of the reference inputs. In addition, they may be configured as Distribution Time and Frequency (DTF) systems that are synchronized by an external reference. Dual Redundant systems (CommSync II & CommSync II-D) may be configured with two GPS Time & Frequency (GTF) modules and two power supply modules (AC and/or DC power) for redundancy with uninterrupted automatic switchover.
-
Product
IRIG B Booster
-
Signals & Systems India Private Limited
IRIG B Booster – SIB-1010 is used to boost the IRIG-B AM and PWM/TTL signal which is received from the GPS unit. It provides easy and affordable connectivity to substation equipment and power generation and distribution equipment. With this Plug-N-Play unit, you can expand your IRIG B connections to multiple devices instantly. It is rugged and surge-protected equipment. Its cabinet can be mounted directly on a wall, panel or DIN Rail, without the need for additional brackets. It has an inbuilt power supply module, therefore, doing away the need for an external power adapter.
